Question about 1999 Mercury Cougar

Open Question

Removing the door panel of a 1999 mercury cougar

Trying to remove the panel to remove the motor for the power window

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: electic window motor removal

There are 2 torx head screws on the inside trim piece where the door latches (right side) and one on the left and you will need to pry off the cougar logo on the handle and remove the screw. Now remove the two plastic covers off the lower, carpeted area of the inner door trim and remove the screws. I couldn't remove the left one so I ended pulling off with it attached which did not cause any harm for me. the trim then just 'pops' off the sides and bottom then you need to lift it up off clips on the top. Remove the insulating cover, which will probably just rip anyway. You will then see 3 large silver torx head screws which hold the motor on. I had to jostle the motor a very little to loosen it up after the years of being screwed on but it came of very easy. Good Luck!

Posted on May 27, 2009

Ad
  • 490 Answers

SOURCE: POWER WINDOW 91 MERCURY GRAND

You have the ribbit on type,they have to be cut off to remove or drilled out.This should be done by a professional as these are dangerous and can take off you fingers if you dont know what your doing.

Posted on Jul 24, 2009

ZJLimited
  • 17970 Answers

SOURCE: how to remove the door panel on 1991 mercure

DOOR TRIM PANEL

1989-92 Models
(see Figure 8 - click over pic for zoom)

  1. Remove window regulator switch housing.
  2. Remove the door inside handle cup (snaps out).
448e137.jpg

Fig. 8: Door trim panel-1989-92 models
  1. Remove the self tapping screw retaining door trim panel upper front extension assembly, and remove assembly.
  2. Remove the two self tapping screws retaining door trim panel to the door inner panel.
  3. Lift the door trim panel upward and snap out trim panel.
  4. Disconnect the wire harness for courtesy lamp.
To install:
  1. Attach the wiring harness to the courtesy lamp.
  2. Place the door panel into position, then tighten the panel to the inner panel.
  3. Attach the upper front extension assembly.
  4. Snap the door handle cup on the door assembly.
  5. Install the window regulator switch housing.


Electric Window Motor
REMOVAL & INSTALLATION
  1. Remove the trim panel and watershield.
  2. Remove the speakers.
  3. Disconnect the negative battery cable.
  4. Disconnect the motor wires and the connector.
  5. Using the dimples located on the inner door panel, drill 3 / 4 in. (19mm) holes for access to the motor.
WARNING When drilling the holes, the glass must be in the up position. The hole saw pilot must not extend more than1/4in. (6mm) beyond the hole saw.
CAUTION Secure the regulator in a vise and drill a5/16in. (8mm) hole through the regulator sector gear and the plate. Install a1/4in. (6mm) bolt and nut in the hole to prevent the sector gear from moving when the motor and drive assembly is removed.
  1. Working through the holes, remove the 3 motor and drive-to-regulator attaching bolts. Remove the motor and drive from the door.
To install:
  1. Clean the chips of metal from the surrounding area. Then coat the bare metal to avoid rust.
  2. When installing the motor and drive to the regulator and install the 3 screws just snugly enough to hold it. Remove the regulator restraining bolt and nut if the old regulator was re-used.
  3. Connect the negative battery cable.
  4. Connect the wires and cycle the glass through its run to ensure gear engagement. Then, tighten the attaching screws to 50-85 inch lbs. (6-10 Nm).
  5. Install the speakers and door trim panel with watershield.

Hope helps (remember rated this).

Posted on Jun 25, 2010

  • 1 Answer

SOURCE: how do i remove the door panel on my 1999 mercury

****'D

Posted on Oct 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I am having trouble with my 1990 Mercury Cougar window. The power window was running and would not go down so I forced it down half way. The motor is running but nothing is moving... Since I pushed it down...


You'll have to replace the regulator/motor assembly with a new one if the mechanism was damaged, which sounds like it was. Plastic parts break on these systems. If it is snowing and you don't have the resources to replace it right now, try to tape some plastic over the window using duct tape. But, this is only a temporary solution.

Nov 04, 2011 | 1990 Mercury Cougar

1 Answer

99 mercury cougar replaced power window motor and switch window still does not work


That doesn't seem possible does it ?

You remove the inner door panel

You think the motor may be bad,so you unplug it,
knowing it is a DC Motor & can be hooked up either
way & will run in either direction
You put 12 volts to it. Doesn't work ,sounds bad,you
install a new one

Now you need power from the switch to run the new motor,
so you work on that
The switch can be disconnected & tested with an OHM Meter
& if worn,you replace that
You checked the fuse before you started & knew that wasn't an issue,
because all the other windows worked

So what did you mis ,short of having no wiring diagram, to make
things a lot easier?

Aug 04, 2011 | 1999 Mercury Cougar

2 Answers

Blower motor removal in a 1999 mercury cougar


SECTION 412-02: Heating and Ventilation 1999 Cougar Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 02/8/2001 Blower Motor Removal
  1. Remove the footwell upper trim panel (passenger side).
    • Remove the pushpins.
    m3401035.jpg
  1. Remove the blower motor.
    1. Disconnect the electrical connector.
    1. Lift the securing tab, turn the motor approximately 30 degrees counter-clockwise and remove the motor.
    m3401077.jpg
Installation
  1. NOTE: Engage the securing tab for the blower motor.

Nov 12, 2010 | 1999 Mercury Cougar

1 Answer

How do i change a blower motor in a 1999 mercury cougar


Blower Motor Removal
  1. Remove the footwell upper trim panel (passenger side).
    • Remove the pushpins.
  1. Remove the blower motor.
    1. Disconnect the electrical connector.
    1. Lift the securing tab, turn the motor approximately 30 degrees counter-clockwise and remove the motor.

Jan 10, 2010 | 1999 Mercury Mountaineer

1 Answer

How to remove a door panel on a 95 Mercury Cougar


find any screws and take them out first then u want to slide the panel upwards until it releases

Jul 31, 2009 | 1994 Mercury Cougar

1 Answer

Electic window motor removal


There are 2 torx head screws on the inside trim piece where the door latches (right side) and one on the left and you will need to pry off the cougar logo on the handle and remove the screw. Now remove the two plastic covers off the lower, carpeted area of the inner door trim and remove the screws. I couldn't remove the left one so I ended pulling off with it attached which did not cause any harm for me. the trim then just 'pops' off the sides and bottom then you need to lift it up off clips on the top. Remove the insulating cover, which will probably just rip anyway. You will then see 3 large silver torx head screws which hold the motor on. I had to jostle the motor a very little to loosen it up after the years of being screwed on but it came of very easy. Good Luck!

May 18, 2009 | 1999 Mercury Cougar

1 Answer

Blower motor fuse is located 99 mercury cougar


SECTION 412-04: Control Components 1999 Cougar Workshop Manual REMOVAL AND INSTALLATION Blower Motor Resistor Removal
  1. Remove the upper footwell trim panel (passenger side).
    • Remove the pushpins.
  1. Disconnect the blower motor resistor electrical connector.
  1. Remove the blower motor resistor.
-------------------------------------------------------------------------
f9d16f6.gif

May 06, 2009 | 1999 Mercury Cougar

2 Answers

1993 Mercury Cougar power window, driver side, will not move


It could be one of about 3 things, the switch could be bad, the motor, or the window regulator. Sometimes you can hit the lower part of the door a couple of times wile holding the window switch to check the motor. I don't know how to check the switch but the cable on the regulator can brake and wrap around the motor not allowing it to run. The only way to check this is to take the door pannel off and see if the cable is broke.

Jan 01, 2009 | 1993 Mercury Cougar

2 Answers

1995 Mercury Cougar Door Panel Removal


This nearly drove me crazy on our 1994 Cougar.
First remove the electric switch cover(window and mirror controls). Just pops out with a pry. Remove the harness attachments You will see a single screw into the door holding a bracket between door pad and door frame. Remove it.
Second, remove the door lamp plastic cover at the bottom rear of the door. You will find a second screw in there on the upper right corner. Remove it and you are ready. Pull the whole door pad upward and it comes right off. No popem plastic clips or anything else. Just 3 or 4 quarter circle retainers that pop over into the door when you push the pad back down

Oct 26, 2008 | 1995 Mercury Cougar

1 Answer

1999 mercury cougar bloswer motor removal


Yes there is a samll tab located on the bottom, if you bend it down and twist it should spin right out.

Jun 20, 2008 | 1999 Mercury Cougar

Not finding what you are looking for?
1999 Mercury Cougar Logo

Related Topics:

686 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

fordexpert

Level 3 Expert

5546 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...