Question about 2004 GMC Yukon

1 Answer

Air vent not working on two lowest settings. started about a year ago with only the lowest setting not working. now the second to the lowest setting is not working either. could this be a faulty blower resister/relay?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

CHECK YOUR WIRING BEHIND YOUR HEATER CONTROL RESISTOR AND CONNECTOR MAY BE BURNT

Posted on Jun 22, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1975 k5 blazer and it blows cold air it worked fine last year but now it only blows cold air even on the defrost setting what can the problem be and how can I fix it?


A vent flap actuator probably needs to be replaced. It's what moves your vent flaps from heat to A/C or to plain "vent air" when you change settings.

The discussion in the link includes vent flap actuators. Unfortunately, they also include the infamous no low speed fan problem too.

Cannot get any air from dash vents while defrost and floor vents work fine...

Your particular actuator will be a different one than they found.
They're all a absolute pain to get at because they can be well buried in the dash. I would start looking under the dash on the passenger side, that's where most of the air control is. Cannot get any air from dash vents while defrost and floor vents work fine...

Nov 14, 2016 | Cars & Trucks

1 Answer

Montana ac problem


some external sensor has taken a knock etc
sounds like its not getting whats going on outside
or the evaporator has an issue with its drains
perhaps something in the air intakes

Dec 23, 2014 | 2001 Pontiac Montana

1 Answer

My air condition and heat works on defrost only sometime comes out vents last seconds didn't matter were controller set


Not sure what year, make or model vehicle is in question, but the issue is due to an actuator that has gone bad. Sometimes referred to as a mode actuator or blend door actuator. This actuator controls where air/heat will blow from (defroster vent, forward vents, floor vents or combo, etc.). Good luck. Ron @ Speed-O-Repair.

Aug 24, 2014 | Cars & Trucks

1 Answer

Replace blend door actuator motor


Could be, check the door and see if it works correctly

Aug 17, 2013 | Mitsubishi Cars & Trucks

1 Answer

No air/heat coming through vents


u more then likely have a bad blower motor resistor

Jun 20, 2013 | 2000 Chevrolet Blazer

1 Answer

Heating system do not work. It started a couple of weeks ago. When set at 70, it produced no warm air. cold air would come from the vent/duct. when increasted to about 76, it would produce heat. Now it do...


I have the exact same problem. Started occasionally blowing cold air. Now I can't get the hot air to come through. Could it be a flapper door that open and closes depending on the tempurature setting?

Jan 04, 2011 | 2006 Lincoln Mark LT

1 Answer

2001 Nissan Sentra Air Conditioning problem


good day, try to check the compressor maybe thats the problem. i hope this tip will help you.

Jun 05, 2009 | 2001 Nissan Sentra

1 Answer

2002 New VW Beetle is only blowing hot air out of vents even when set on cool. I was driving and I made a turn at an intersection and all of a sudden the cool vent air turned to hot air like I had the heat...


On the bottom of the air unit is the lever that changes temps. It likes to fall out of place.I propped mine back with a piece of half-inch copper pipe a couple of years ago.Remove glove box then panel on front side of console to access.

Apr 09, 2009 | 2003 Nissan Altima

Not finding what you are looking for?
2004 GMC Yukon Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...