Question about 2000 Chevrolet Cavalier

1 Answer

Rear rotors front shoes

I was just wondering how much would i should be looking to pay for the repairs.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 50 Answers

Pads rotors drums shoes kombi kit 600+tax

Posted on May 31, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lack of braking since new. Have tried best combo's of rotors, front disk brake pads & best rear drum shoes !


Bleed the breaks untill you get clean clear fluid out of each one. start with the right rear, left rear, right front, left front. DO NOT let the reservor get low while bleeding. You can suck air into the lines and have the same problem. You need to do this immediatly as your brakeing ability is uncertain and can be un reliable.

Jan 31, 2013 | 1998 GMC Suburban

1 Answer

Emergenct brake will not hold


The linkage could need to be adjusted. Or the brake shoes inside the rear drums are worn out and need to be replaced. If you accidentally drive the brake on. It doesn't take long to wear those brake shoes out. You can normally smell them when that happens. On today's vehicles they are actually designed with 3 different brake systems. Front brake disc and rotors, rear disc and rotors, and inside the rear brake rotor their is a small brake drum where the emergency brake shoes are located. The only purpose for the shoes and drums is emergency brake only (normally). Hope this helps.

Nov 27, 2012 | Cars & Trucks

1 Answer

Is there a certain way to change rear brake rotors. They seem to be frozen and will not come off. I did not see a set screw in the rotors like some of the new models have.


ok i have been doing the for 22 yrs..heres the prob...inside the rear brake rotors r ur parking brake shoes..there is either a rust lip the built up on the inside of the rotor causing the parking brake shoes to grab the rust lip when u try to remove the rotor..if this is the case u will also need to repalce the rear parking shoes and the parking brake shoe holddown spring kit since it will probably break when u have to pry the rotor off....or u maybe able to de adjust the rear shoes by the self adjuster...look on the back side of the other side of the brake rotor an u should see a over slot just below the control arm...if it there use a brake spoon or straight slot screw driver to de adjust the rear park shoes.move it up or down ..one way will tighten them the other way will loosen them...if ur rotor doesnt move at all take off the rear caliper an hit the back side of the brake rotor to knock it off

Jul 16, 2011 | 1998 Ford Explorer

1 Answer

Need instructions for installing parking brake shoes on a 2001 Dodge 3500 pickup


This is a big job for such a small part. I suggest you repair/replace rotors, pads, and anything else back there while you are at it. You will need to remove both wheels on both sides, as well as the axles (I think). See my earlier post on Rear Rotor removal to see how this is done.

You will need a large spindle nut to remove the axles.

DISASSEMBLY:
Once you have access to the parking brakes inside the rotor hat:
1. Lock out the parking brake w/a pair of Vise grips (on the parking brake cable under the cab)
2. Disengage teh park brake cable from behind the rotor assembly to allow easier disassembly of the parking brake shoes.
3. Disassemble the rear park brake shoes.

REASSEMBLY:
1. Reassemble the rear parking brake shoes. This is a typical, small brake drum configuration. Do one side at a time - so you can see how to reassemble each small part. Keep the springs and parts oriented the same: front to front and interior to interior, etc.
2. Release the parking brake cable
3. Install the disc brake rotor(s)
4. Install the disc brake caliper(s)
5. Install tire & wheel assembly
6. Lower the vehicle

Sep 07, 2010 | 2001 Dodge Ram 3500 Truck

2 Answers

How to remove brake rotors on a 1996 ford explorer


How to replace the rear brake pads on a 1995 through 2001 Ford Explorer The system utilizes a drum-in-hat type rear brake rotor. The integral drum allows the use of a drum-and-shoe type parking brake system. All other components are similar to their front disc brake components Remove the two bolts on either side of the brake hose with the rubber boots. Do not remove the four bolts where the axle ties in. The two bolts to be removed require a 10mm socket/wrench. Loosen the pads from the caliper Rotor Removal In order to take the rotors off (replace with new or have them machined), it is best to loosen the emergency brake shoes. To do this, behind the rotors, in the back there is a rubber plug, remove that and you can use a screw driver to engage the teeth of the adjusting screw, turn it clockwise to loosen, usually 10-20 teeth. Usually this means turn it downward. After this, it may still be difficult to get the rotors off without tapping them. Use a rubber mallet and hit them from behind. Before really whacking the rotor, make sure you have loosened the adjusting screw enough. It may take heavy swings of the rubber hammer to do this. It will eventually break loose. Parking Brake You might want to check the parking brake while you are here. To remove:
  • Remove the rear disc brake rotor.
  • Remove the outboard return spring.
  • Remove the adjusting screw spring.
  • Remove the rear brake shoe hold-down spring and pin.
  • Remove the brake shoe adjusting screw and nut.
  • Remove the front brake shoe hold-down spring and pin.
  • Remove both parking brake shoes and the inboard return spring.
  • Check the parking brake lever for excessive wear and replace as necessary.
To install:
  • Position the front parking brake shoe to the backing plate and install the hold-down pin and spring.
  • Install the rear parking brake shoe with the inboard return spring.
  • Position the brake shoe adjuster screw and nut on the shoes and install the rear shoe hold-down pin and spring.
  • Install the brake shoe adjuster spring.
  • Install the outboard return spring.
  • Adjust the parking brake shoes and install the rotor, caliper and wheel.
  • Lower the vehicle and tighten the wheel lug nuts to 100 ft. lbs. (135 Nm).
ADJUSTMENT
  • Measure the inside of the drum portion of the rear brake rotor
  • Remove the rear disc brake rotor.
  • Using Brake Adjustment Gauge D81L-1103-A or equivalent, measure the inside diameter of the drum portion of the rear disc brake rotor.
  • Subtract 0.020 in. (0.508mm) from the first measurement, adjust the brake shoes to that size
  • Adjust the parking brake adjuster screw until the outside diameter of the parking brake shoes measures 0.020 in. (0.508mm) less than the drum measurement.
  • Install the rear disc brake rotor.
Reassembly Reassembly is easy. Put new or machined rotors back on by sliding them over the lugs (they should slide on easily.) Loosen bleeder valve (having a catch bottle handy is good). Push calipers in slowly (using a c-clamp or large channel lock pliers), close bleeder valve. Put on pads. Lubricate metal clips with small amount of anti-seize. Re-adjust the emergency brake by turning the opposite direction from loosening. Refill the brake master cylinder

Aug 09, 2010 | 1996 Ford Explorer

1 Answer

Asking which kind of brake in back rear driver makes a lot a nois


You have brake rotors and pads on the front. Looking on the rear axle if it looks like the front it will be rear rotor and pads. And if you cannot see the rotor or pads on the rear axle then you will have what is called rear drums and brake shoes. Hope this will help you.

May 20, 2010 | Cars & Trucks

1 Answer

2006 town and country rear brake rotor removal. After several beatings, i cant get the rear rotors off my town and country. They are alittle loose, but am wondering if i have to do something with the...


yes the e brake shoes inside the rotor tend to create a lip that will hang them up just bake them off a bit and you should be able to pull them off fairly easily also check to be sure that the stock assembly line retainer clips have been removed from the front of the rotor they are just thin looking washers that are pushed on to the lug nut studs to hold the rotor in place on the assembly line a pair of side head cutters work well to remove them and discard after removed.
Hope this helps.

Feb 13, 2010 | 2006 Chrysler Town & Country

2 Answers

I have a brake fluid leak. I dont know what the


The part is called the wheel cylinder. (Not to be confused with the master brake cylinder that is under the hood and provides the pressure for the brakes to operate.

On a 1993, I suspect you have drum brakes, so the part you are describing as a rotor, (and that looks, well, round like a rotor), is actually not called a rotor. That is reserved to describe the round heavy plate on the front wheels.

Newer cars actually would possible have disc brakes with rotors on the front and rear wheels.

More than likely, especially on a 1993 vehicle, the seals in the wheel cyclinder are shot. Not sure how hard it is to get replacement parts, but the same re-build kits would likely have been used on several years and models of GM cars from the early to mid-90s.

Oct 07, 2009 | 1993 Oldsmobile Cutlass Supreme

1 Answer

How do you adjust the rear brakes on a 05 kia spectra5 ? It has disc brake front and rear.


Disc brakes are not adjustable. You may have a parking brake that is like a mini- brake shoe in the middle of the rear rotor. Those are adjustable, but tough to get at, and they rust badly. Look to see if your "cable" goes either to an arm that actuates the shoes, or if it goes to the caliper. If it goes to the caliper, you have no parking brake shoes.

Jul 28, 2009 | 2007 Kia Spectra5

1 Answer

2004 pontiac grand am


Did you "scuff" up the front rotors??? Sounds like the may be "glazed". Also if the rear drums did come off that easy I suggest adjusting. You should feel very slight "drag" when you spin rear drum. Good luck

Jun 29, 2008 | 2004 Pontiac Grand Am

Not finding what you are looking for?
2000 Chevrolet Cavalier Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8211 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...