Question about 2006 Peugeot 405

1 Answer

Peugeot ae ****

My new clutch is still slipping had new flywheel and clutch kit fitted peugeot expert

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

1) CHECK THE ADJUSTMENT OF THE CLUTCH PEDAL, CHECK ITS FREE PLY.


2)ALSO THIS CAN HAPPEN IF ENGINE, GEAR BOX OR SELECTOR SHAFT SEAL IS LEAKING

3)PEUGEOT OFFERS A WARRANTY OF 1 YEAR FOR THE PARTS FITTED. EVENTHOUGH THE WEAR & TEAR PARTS ARE EXCLUDED, IF YOU HAVE FIXED GOT IT FIXED EARLIER WITH IN THE PEUGEOT NETWORK & IT REALLY IS THE DEFECT OF THE PART, YOU STILL HAVE A CHANCE.

www.thejavedmiandad.com

Posted on Jun 30, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do i no if my clutch needs replacing in my 1997 peugeot 306 convertable


Certainly, that's one way! If the clutch is worn out, it will "slip". A way to tell is to put the car in 3rd gear and rfev the engine just alittle and then let ehte cutch "out." If the engine continues running, the clutch is slipping. You may be able to smell "something" buring as well. That would be the clutch disintegrating.

Be sure to have the flywheel inspected for damage when the clutch is replaced. It may only require resurfacing but it may need ot be replaced.

Feb 11, 2015 | 1997 Peugeot 306

1 Answer

How do I line-up the flywheel timing marks and where are they. I fitted new clutch and had to remove the flywheel


There should have been a dowel pin in crank flange so the flywheel would go back in the same spot. Is it a new flywheel? Was it balanced? There are no timing marks on the flywheel. Does the gear on the starter line up with the flywheel teeth? Does the engine turn over? Would like to help.

Jan 29, 2015 | Cars & Trucks

1 Answer

How to tell if a flywheel is bad


most flywheel faults are heat related caused by a slipping clutch . Remove the transmission and inspect for , blue color heat spots . small cracks. scores caused by a worn out driven plate, run out check with a dial gauge. most flywheels can be machined as good as new . All ways fit a new replacement clutch kit with a new throw out bearing.

Oct 31, 2014 | Cars & Trucks

1 Answer

Peugeot partner van


Yes probably, it is causing it to slip. The longer you leave it, the quicker you will burn out the clutch.

Nov 29, 2017 | 2005 Peugeot Partner

1 Answer

This is mike @ terrys north coast in cleve ohio,installed new clutch kit in 91 honda accord 5 speed ,and new flywheel ,clutch is fine engauges at half pedal,when clutch is used for an extended period it...


If the clutch is hydraulic, it most likely has some air in the line. I had that problem on my 87 Saab. When it got hot the air would expand and the clutch would slip. In my case the master clutch cylinder was leaking and allowing air to enter the system.

Jim

May 01, 2011 | Honda Accord Cars & Trucks

1 Answer

I have a expert 2005 it has lack of power going up hills wit just has no grunt it has just had a conversion done from a dual mass flywheel to a solid flywheel i have check the ecu but no codes i have...


The setting for clutch are not proper hence clutch is either slipping too much or sticking too much to clutch plate causing the engine to overload for every single rev. Both will effect the efficiency of your engine's exerting power especially going up hills. Use the manufacturers specification for clutch force and adjestment of pressure plate.

Try this to find out the condition of your clutch system:
In first gear and push accelerator fully to drive upto 3500 revs and then suddenly move your foot away from accelerator. If you feels a sudden shock and your head tends to nag to windscreen with a force then clutch adjestments are not properly done (stifting force is more than recommended). Inversly clutch is not engaging fully.

Jan 15, 2010 | Peugeot Liberte Cars & Trucks

1 Answer

Peugeot 106 1.5D. the clutch was slipping so new clutch fitted 2 weeks ago. It was still slipping so that garage replaced the clutch again. Guess what? It is still slipping. Any idea what is going on?


Yes clutch pedal should start to drive about 1inch off the floor and when driving keep your foot away from the pedal,/ also when new clutch is fitted did they fit a complete clutch assy /and did they surface grind the flywheel as if it was badly worn on the 1st one then the new one wouldent last very long.
as when the clutch starts to drive 1" from the floor clutch is good /when it engages right out its buggered and slips so ask about the f/wheel

Oct 02, 2009 | 1991 Peugeot 405

1 Answer

Engine


Valeo car parts does a clutch assembly complete with modified flywheel as well,so its a conventional type clutch without being the back to front one thats fitted from new.BUTS ITS EXPENSIVE about 800€ but it works

Feb 17, 2009 | 1987 Peugeot Liberte

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

573 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

mike hayward

Level 2 Expert

279 Answers

Wahs Team

Level 2 Expert

215 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...