Question about 1996 Chrysler Concorde

1 Answer

Turns over but will not start--was running fine

94 concord just stopped running--i was driving and heard a small pop. it was running fine and stopped all of a sudden. it will turn over but will not start

Posted by on

  • cfpkelly May 30, 2009

    thank you--how do i check to see if its the timing belt?

  • cfpkelly May 31, 2009

    thank you again

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,392 Answers

Sounds like your timing belt popped. Hope you didn't mess up the motor when it went. May have bent some valves. Has it been awhile since it was replaced? Check it first.

Posted on May 30, 2009

  • Eldric Venne
    Eldric Venne May 30, 2009

    You need to take off the timing cover. It is a 2 or 3 piece design. Only 1 piece needs to be removed for inspection.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Unfreeze a gasline 94 concorde


How much is almost no gas? When it was running did it run ok?
Does it turn over? All of these details would have been included
in a question from a rational person which obviously you aren't.

Dec 22, 2012 | 1994 Chrysler Concorde

1 Answer

Stopped running while driving


i would first check the crank position sensor,i have seen this many times before.

Feb 16, 2010 | 1997 Chrysler Concorde

1 Answer

1999 Chrysler Concord won't start at times and dies while driving


Have somone check the timing belt make sure it has not jumped any teeth common problem on a old car with high mileage.

Sep 02, 2009 | 1999 Chrysler Concorde

2 Answers

1990 Grand Am won't take fuel after loud "pop"


when you turn the switch on listen in the fuel tank to see if the fuel pump comes on

Jun 29, 2009 | 1990 Pontiac Grand Am

1 Answer

94 Chrysler Concorde Tranny Problems


Have your transmission oil filter changed;
it is located under the transmission pan
The oil is what makes the transmission shift
When you shut off the engine it stops the transmission pump then when you start up again the transmission shifts until the filter clogs again

May 28, 2009 | 1994 Chrysler Concorde

2 Answers

OIl pressure light flickers


change the oil pressure switch or the wrong oil

Jan 18, 2009 | 2001 Chrysler Concorde

1 Answer

Shut down


This happened to me on my 94 concord. I had to replace the ign. switch.

Dec 18, 2008 | 1994 Chrysler Concorde

3 Answers

97 concorde with 3.5 engine @ 40 to 45 mph it starts bucking .


Computer firmware needs upgrade

Take your car to a Chrysler dealer shop and have them update the transmission program.As your tranny wears it loses it shift point and stutters between 40 - 45 mph looking for the right gear to change to..Had same problem in 94 Concorde and 94 T&C minivan.Reprogramming tranny fixed both cars.

Nov 22, 2008 | 1997 Chrysler Concorde

2 Answers

1998 jaguar vander plas


1. How many miles on your car?

2. Is the engine hot, when you try to start the car?

3. Is the engine hot, when you heared the knock noise?

Jul 09, 2008 | 2002 Jaguar Vanden Plas

1 Answer

94 Concorde electrical


I have a similar problem with my 94 concorde... and was advised the on board computer was in need of replacement. Further research led to pulling the computer and cleaning the ground connection to the chassis. It will sometimes leak under the computer and corrode, and compromise the ground, which in turn will cause faulty "code" readings and the engine control light to come on.

May 24, 2008 | 1994 Chrysler Concorde

Not finding what you are looking for?
1996 Chrysler Concorde Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8211 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...