Question about 1996 Ford Econoline

1 Answer

Where is the clutch fluid reservoir

I bought a 1996 Ford Econovan Maxi (second hand) didn't get a user manual with it, cannot seem to find if there is a separate clutch fluid reserve, or it's shared with the brake fluid one. Tried searching on the net for a user or service manual, but can't even seem to do that. Please help.

Posted by on

  • wabel May 30, 2009

    Thankyou so much, very appreciated

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 58 Answers

If it's a hydralic clutch, then it's shared

Posted on May 30, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How much water goes into the cooling system of a ford econovan maxi 1995


depending on which engine you have ,you are looking at 12 to 16 litres when empty

Feb 23, 2015 | Ford Cars & Trucks

1 Answer

FORD ECONOVAN MAXi 2.0 Hi, i have a serious creaking and groaning noise from the front nearside when I hit a bump or speed hump could I need a new shock absorber? I dont get the bump I would expect


It could be your shock/strut for sure. It could also be other suspension parts like the control arm or ball joints but I would suspect shocks first. If you arent extremely proficient, I would leave this repair to the pros. It isnt hard but it is incredibly dangerous. To get the old shock off you need to compress the spring with a special tool, and once it is compressed, it is like a bomb waiting to go off and could easily kill you. Take it to a shop and have them confirm the problem then do the repair. It should be around 150 for the part ( or less!) and another 100 for the labor.

Jul 10, 2014 | 1992 Ford Econoline

1 Answer

I have a 1990 econovan ,with a 13b rotary, have changed the clutch master cylinder and kant seem to bleed it, help please


You may need to prime the master cylinder first. Disconnect the line at the master cylinder and place your finger over the hole. Have some gently pump the pedal while you finger acts as a non return valve That is when the pedal is depressed allow fluid to escape and when the pedal is release use you finger to stop air getting back in. If you have a line that is higher than the slave cylinder (where the flexible hose joins the steel line )loosen here and depress the pedal and retighten before the pedal is released . Keep doing all procedures until you get solid fluid out. Finally bleed out the slave cylinder as normally would be done.. Remember air collects at the highest point in the line and fluid will not move as a solid block but will run past the air and not push it out so you have to bleed the high points.

Aug 22, 2013 | 1996 Ford Econoline

1 Answer

How to replace clutch master cylinder Ford Econovan Maxi 1993 without pulling the entire dash out?


Wait. Maybe you're in the wrong place. All cars I have seen have the clutch master cylinder bolted to the firewall inside the engine compartment. You take off the line going to the clutch, remove two bolts or nuts holding the unit to the firewall; and remove the unit. The only thing maybe to remove under the dash is the pushrod from the clutch pedal to the master cylinder.
Now if yours is different, then proceed, but check under the hood for the clutch master cylinder first.

Nov 02, 2012 | Cars & Trucks

2 Answers

Valve clearances for a ford econovan 1.8lt, 1990


what are the valve clearance specs for a 1990 ford econovan maxi

Mar 14, 2010 | 1989 Ford Econoline

Not finding what you are looking for?
1996 Ford Econoline Logo

Related Topics:

688 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...