Question about 1996 Ford F250 Crew Cab

1 Answer

No start no rpm during cranking replaced cam sen,

No start

Posted by on

  • rsap May 30, 2009

    is there a cr sen. on desieles and if so can it cause a no start

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 24 Answers

Engine speed is calculated from the crankshaft sensor, not the cam sensor. cam sensor only used to denote no 1 cyl TDC

Posted on May 30, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2006 nissan x terra. spins over, wont start. replaced fuel pump assembly, crank sensor, left side cam sensor. not getting any cranking rpm from scanner. HELP !


This already sounds all kinds of bad.
Lets start with spark. Did you verify it can make 30kv at all plugs while cranking? f you havent...start there. Do you have any codes in any modules? Engine, theft, trans, body?
Do you have vacuum cranking, do you have MAF reading cranking? do we know if its mechanically still in time? Did you do a cranking compression test? If you have spark, and you remove the fuel pump relay...does it start when it isnt flooding? What is your system and reference voltage...what is cranking vacuum? And what tests did you run that inspired changing all that stuff? Check the c ranking rpm in Generic mode just rpm onscreen, some OEM software doesnt update well during cranking, with one pid selected, solus should update better than 10x a sec, If you still have no signal...you need to measure the crank sensor wires or verify the crank sensor ring is even turning,

Jan 05, 2015 | 2006 Nissan Xterra

1 Answer

I have a 03 mits endevour 3.8litre pwr steering belt broke had both belts replaced tried start the vhicle.cranks but won't start.


Check at the area of where the belt snapped what sensors and plugs and wiring could be affected. Most probably either a broken wire or broken or unplugged any connector.or any sensitive sensor has been damaged.

Mar 03, 2014 | 2002 Kia Sportage

1 Answer

03 mitsubishi eclipse 2.4 4 cyl miss fire on 2 and 4 cyl going by the firing order they are not getting fuel the car was running fine shut it off went back 2 hours later and that's when it started...


If you know for a fact the injectors are not opening, you would need to check for voltage and a ground signal from the computer. The computer grounds the injectors to open them based on the crank and cam sensors.

Jan 03, 2013 | Cars & Trucks

2 Answers

Car will not start change out camshaft sen, crank


maybe a dicky cam sensor even if new! make sure the cam sensor is aligned correctly as if its out even a small amount the car will not run. check it is in place correctly.

Is the car trying to start? or are you getting nothing when turning the key?

Jan 17, 2010 | 2003 Mazda Mazda6

1 Answer

97 Chevy Astro van lugs, like it misses, B4 finally cranking on


crank shaft sen. is easy enough to change.its mounted near timing chain cover,cam sen.is somewhat harder,its in the distributor,id doubt that both are defect

Mar 09, 2009 | 1995 Chevrolet Astro

1 Answer

Pos. jumped time .


wet distributor if it rains allot or is humid than sometimes they get wet and wont work properly or get rusted under the cap

Dec 07, 2008 | 1997 Chevrolet K1500

Not finding what you are looking for?
1996 Ford F250 Crew Cab Logo

Related Topics:

105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...