Question about 1999 Hyundai Sonata

1 Answer

Loose rear wheel, believe it is the bearing. How do I repair it?

I want to replace the rear bearing. How?

Posted by on

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hyundai Master
  • 14,036 Answers

Drum brakes you remove rear wheel- speed sensor-grease cap-flange nut-outer bearing-brake drum-inner grease seal-inner bearing-drive the bearing races out of the drum hub.to install -install the inner and outer bearing races.apply grease to the bearings and hub cavity.then you install the inner bearing -inner grease seal-brake drum-outer bearing-flange nut torque it to 159 to 192 ft lbs. THE REAR DISC BRAKE WHEEL BEARINGS-you have to remove rear wheel -wheel speed sensor-brake caliper and rotor-rear axle hub bolts-tone the wheel with tool 09445-21000-carrier assembly-nut after unstaking it-press out the rear axle hub-remove the bearing inner race with tool 09445-21000-remove the bushings from the carrier with tools 09453-33000b and 09545-21100.to install -press in the bushings to the carrier with tools 09453-33000b and 09545-21100- press in the bearings to the hub with tool 09221-21000.tighten the flange nut to meet the concave portion of the spindle-press in the tone wheel with tool 09221-21000-torque the nut to 191 ft lbs -install the hub and bearing assembly to the backing plate and torque the bolts to 88 ft lbs-install the brake caliper and rotor.install the wheel speed sensor if equipped.install the rear wheel.TO BUY THE TOOLS TO DO THE JOB.LOOK UP KENT MOORE TOOLS ON INTERNET.

Posted on May 30, 2009

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 72 Answers

SOURCE: rear wheel loose

Jack it up..take off the wheel and look, ASAP! Is it grinding when you spin it? Is there visible oil leakins or visible metal shavings. Sounds like a bearing to me.

Posted on May 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

1999 mercury cougar v6 when jacked up on rear whole tire wiggled back and forth


Bad wheel bearing. I do believe yours are pressed in. You can remove the spindle and take it to a shop and have them replace the bearing.

Jan 01, 2017 | Mercury Cars & Trucks

3 Answers

1994 LINCOLN CONTINENTAL


Hi Terry,
Please check out this Link : http://www.autopartswarehouse.com/featured/books_and_manuals/1461465620.html
Here you will find the details regarding your Car and how you can check and repair the breaks without taking it to a mechanic.
I hope this helps.....

Jun 02, 2008 | 1994 Lincoln Continental

1 Answer

I have a 1999 cougar and the back end keeps pulling out to the right like my drivers side wheel is locking up. What could be causing this??


Hello, some of the Front wheel drive cars used a rear suspension system which requires an Alignment just the same as the front end. You can get the rear Alignment separately but it is usually a packaged 4 wheel Alignment. Jack up the back end of the car and turn the wheels and check for them turning hard. This will indicate a brake or bearing problem.

The rear wheels do have an Emergency brake which can cause problems dragging even when not used. The bonded lining falls off the brake shoe when it rusts and the lining falls onto the rotating parts and gets ground up. Sometimes you will hear a noise like loose rust as you stop and start at low speeds. You can also have a sticking rear Caliper or drum brake.

The rear hubs have bearings which can fail; usually you will hear noises or have vibrations when the bearings are worn loose. Your best bet is to remove the rear brake rotor and visually inspect the Emergency brakes and feel the turning of the rear hub bearing. If you do not have the rear brake assembly on the car it will be easier to work on the bearing. Bearings are made 2 ways. The Sealed bearings are replaced as a hub unit. The Serviceable bearings have removeable bearings and races.

You want to have the rear bearing in good shape before having an Alignment. The Sealed bearing hubs are the easiest to replace by removing and replacing only bolts. The Serviceable bearings can require punching out and installing a new race, then packing the bearing with grease.

Some shops do both Brakes and Alignment and some just do the brakes. You can fix what you can handle before getting an Alignment or pay for both jobs. I hope you find my solution very helpful.

Feb 21, 2011 | 1999 Mercury Cougar

1 Answer

How do you remove the backing plate from an '05 Chev Venture rear hub so the hub can be replaced?


The 4 Bolts that Hold the HUB in Also Hold the Backing Plate
Hub Replacement - Rear (Front Wheel Drive/Drum)

Removal Procedure
  1. Raise and support the vehicle.
  2. Remove the tire and wheel.
  3. Remove the brake drum.
    1. Remove and DISCARD the wheel bearing/hub bolts.
    2. Remove the wheel bearing/hub.
    3. Disconnect the wheel speed sensor electrical connector (2).Installation Procedure
    4. Connect the wheel speed sensor electrical connector (2).
      1. Install the wheel bearing/hub. Caution: These fasteners MUST be replaced with new fasteners anytime they become loose or are removed. Failure to replace these fasteners after they become loose or are removed may cause loss of vehicle control and personal injury. Notice: Refer to Fastener Notice in Service Precautions.
      2. Install the NEW wheel bearing/hub bolts.
      1. Install the brake drum.
      2. Install the tire and wheel.
      3. Lower the vehicle.

Nov 07, 2009 | 2005 Chevrolet Venture

1 Answer

My 2005 Impala is making a roaring sound when I turn into a curve driving....What does this mean and how can it be fixed??


It sounds like one of your wheel bearing needs to be replace, most likely one of the rear bearing may have gone dry and needs to be replaced soon as possible before you have a total bearing failure and loose a wheel. With the car parked, go to each wheel and push back and forth on the top (side to side) you should be able to hear and feel which wheel has the play since it's will feel and sound different from the other wheels. The rear wheel bearing can be replaced with simple tool and under 1 hour if your good with tools and the front will have to be brought to a shop since your going to need am impact gun to remove the front axle nut from the wheel hub. Good luck and hope this helps. Keep me posted if your going to replace the rear wheel hub your self and i can give you the instructions to replacing the hub. I believe the rear hubs goes for around $170.00 at Auto Zone and they can give you the step by step instructions too. 

Jul 06, 2009 | Chevrolet Impala Cars & Trucks

1 Answer

Rear wheel loose


Jack it up..take off the wheel and look, ASAP! Is it grinding when you spin it? Is there visible oil leakins or visible metal shavings. Sounds like a bearing to me.

May 30, 2009 | 1999 Hyundai Sonata

1 Answer

Rear wheel bearings on Hyundai Accent


no i do not believe they are press in there are held in by a seal try www.autozone.com to see if they have your car listed if they do you will be able to get a diagram showing you how they come a part.

Apr 24, 2009 | Hyundai Motor 1998 Accent

1 Answer

Replacing front wheel bearing


you need to remove cv axle,makes things easy,i believe the wheel bearing is a "cassette" style.three or for bolts on the backside of knuckle holds bearing assembly in

Feb 11, 2009 | 1989 Plymouth Acclaim

Not finding what you are looking for?
1999 Hyundai Sonata Logo

1,720 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...