Question about 2005 Dodge Dakota

1 Answer

Truck won't start, no click, no nothing

Went out got in my 4x4 with 6 speed standard, unlocked the door with remote, lights flashed on, got inside and inserted key, all lights come on, dash lights up, I turn the key and absolutely nothing else happens. No clicks, no lights dimming just nothing at all. Ran great before. Help!

Posted by on

  • KEN LaPOINT
    KEN LaPOINT May 11, 2010

    Clutch depressed?

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 192 Answers

Here are a few things you can try.
Clean the battery terminals and the inside of the battery cable ends with a wire brush. Make sure the cables are a snug fit back on the terminals. If that doesn't fix your problem check to make sure both the positive and the negative battery cables are good using an ohm meter. You should read just a few ohms. While you're measuring the cables wiggle them around. If you see the resistance jump up while you're doing the wiggling that cable may be bad. Follow the negative battery cable to where it makes connection to the engine block. Make sure this connection is a good clean metal to metal connection. If you aren't 100% sure the battery is good try jumping it with another car.
I hope these suggestions help you out.

Posted on May 30, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What's your question?key program code for 06 xterra


1. Close and lock all doors with the driver's side power lock / unlock switch located
on drivers door panel.

2. Insert key into ignition and remove it from the ignition key cylinder at least 6 times
within 10 seconds. Your hazard lamps will flash if you have performed this step
successfully. NOTE: Withdraw key completely from ignition cylinder each time. If
this procedure is performed to fast, system will not enter programming mode.

3. Insert key into ignition and turn to the ACC position.

4. Within 5 seconds, push ANY button oon the keyless remote. Your hazard lamps
will flash. NOTE: Do not press the button on the remote more than one time or the
programming will not be successful.

5. If there are any remaining remotes (including old ones), Unlock then Lock all doors
using switch on drivers door panel and within 5 seconds press ANY button on the next
remote. Your hazard lamps will flash. Repeat this step for each remote (including any
existing remotes).

6. Turn key to the off position, remove key from the ignition. Unlock door using switch on
door panel and open drivers door.

7. Test remote(s).

Jun 27, 2016 | Cars & Trucks

1 Answer

Program remote


The horn chirp can be disable by pressing the lock and unlock buttons simultaneously until the hazard lights flash, and no enable press the lock and unlock until the horn chirp.
To reprogram (enter new ID) key fob (keyless remote controller) follow the steps.
1. Close all doors and lock all doors
2. Insert and remove the key from the ignition key cylinder more than six times within 10 seconds. (The hazard warning lamp will then flash.) NOTE: Key should be withdrawn from ignition key cylinder completely each time.
NOTE: Do not rush the insertion/removal key cycling process. The side marker/tail/license lamps and interior illumination will flash twice when this step is accurately completed.
3. Insert key on ignition key cylinder and turn ignition key switch to "AAC" position At this time, the new ID code is entered and original (previous) ID codes are erase.
4. Press any button on the new remote controller once. (The hazard warning lamp will then flash)
NOTE: Do not press the button more than one time in the above step. If the button is pressed more than one time, the programming procedure will not be successful. The side marker/tail/license lamps and interior illumination will flash twice when this step is accurately completed and programming is successful.
If there is only one remote controller skip step 5.
5. Additional ID code entry Release the door lock, then lock again with door lock/unlock switch (In power window main switch)
6. Remove key from ignition
7. Unlock driver side door, open driver side door and then close the door. (END)

Feb 20, 2010 | 2001 Nissan Pathfinder

1 Answer

Need to reset the key fob after replacing the battery


You should not have to reset the key fob after a battery replacement. The signal from the key fob stays the same and is programed to the reciever.
If the key fob needs to be reprogrammed then follow these steps.
1. Have all key fobs with you during programming.
2. Sit in the vehicle with all doors closed.
3. Lock all doors using the Lock/Unlock switch on the door.
4. Insert and withdraw the ignition key 7 to 9 times within 10 seconds (do not turn the key, just insert and withdraw).
5. The 4 way flasher indicator on the dash should flash once or twice.
6. Insert the ignition key and turn it on (key on, engine off).
7. Press any button on one remote and the 4 way flasher indicator on the dash should flash once.
8. If you have more key fobs to program use the Lock/Unlock button on the door to unlock the doors and then lock the doors.
9. Press any button on the next key fob and the 4 way flasher indicator on the dash should flash once.
10. Repeat if you have more key fobs. Only 5 can be programmed.
11. To exit, simply turn of the igniton and remove the ignition key.
12. Unlock the doors using the Lock/Unlock switch on the door and exit the vehicle.
13. Make sure the window is down when testing remotes in case you leave the keys inside.
14. Close all doors and test all remotes that were programmed.

Do not skip any steps or the process will not work.

If the 4 way flasher indicator does not work when inserting the key, you will need to start the process from the begining. If it still does not work the receiver may be your problem.

If the 4 way flasher indicator does not flash when pressing any button on the key fob then the key fob is the problem (dead battery or defective remote)

Dec 18, 2009 | 2002 Nissan Xterra

1 Answer

Lost original car alarm control... need to reset a new one...



programing a Nissan remote , is hidden secret by Nissan Dealers. As a Nissan Technician i will share it.

Just get in your vech , close all doors. Using your power lock switch , lock all doors. After doors are locked take your Ignition Key and insert it and remove it from ignition switch in a slow fashion , but consitant pace. (97 and earlyer are fast) When you see the hazzard lights flash, put key in ignition switch and turn to the On postion .. Do NOT CRANK or you will have to Start over .. After in the On postion .. Hit the Lock button on remote... Hazzard lights should flash..( note..you have to reprogram all remotes when adding a new one , if you don't your old remotes will not work ) If your doing just the one , turn igntion switch off and unlock door and get out and try it. If you are doing more than one. While still in Vech with Key on . After you hit the Lock button on Remote and hazzard light flashed .. with key still on .. use master lock switch unlock doors and relock and then hit Second Remote, Lights should flash again , repeat if adding a 3rd remote.. after done just turn key off and unlock door and get out and try.

Oct 29, 2009 | 2002 Volvo S40

1 Answer

Engine won't turn over, no click, no nothing


ck your clutch pedal switch if it is open circuit it won't let the starter engage you can unplug it and jump the the two wires if this doesn't engage the starter you have a bad starter relay and it is located in the fuse box under the hood

May 30, 2009 | 2005 Dodge Dakota

1 Answer

Remote control programming


get into the car , close and lock all doors. insert your key into the ignition in and out 6 times or until your directionals flash. that's when the car is in program mode. you need to pay attention to it while putting key in and out of the ignition. watch your dash for flashing. its kinda hard, but you can do it. so just take your key and put it inside of the igniton and take it out 6 times in a row or until lights flash. when lights flash, put the key in the ignition and turn it to accesorries position (do not start the car). when the dash / cluster lights up after you turn the key, press any button on the remote. your hazards should flash on the dash again. after that happens, take the key out of the ignition and unlock the door with the door lock switch and open the door. remote is now programmed. congrats. you did it.

Aug 15, 2017 | 2005 Nissan Maxima

1 Answer

New key fob


Just get in your vech , close all doors. Using your power lock switch , lock all doors. After doors are locked take your Ignition Key and insert it and remove it from ignition switch in a slow fashion , but consitant pace. (97 and earlyer are fast) When you see the hazzard lights flash, put key in ignition switch and turn to the On postion .. Do NOT CRANK or you will have to Start over .. After in the On postion .. Hit the Lock button on remote... Hazzard lights should flash..( note..you have to reprogram all remotes when adding a new one , if you don't your old remotes will not work ) If your doing just the one , turn igntion switch off and unlock door and get out and try it. If you are doing more than one. While still in Vech with Key on . After you hit the Lock button on Remote and hazzard light flashed .. with key still on .. use master lock switch unlock doors and relock and then hit Second Remote, Lights should flash again , repeat if adding a 3rd remote.. after done just turn key off and unlock door and get out and try. Good Luck :)s.gif

Oct 26, 2008 | 2001 Chevrolet Blazer

2 Answers

Ihave a 1996 Nissan Maxima. I am unable to use the remote keyless entry. I changed the battery but still no good.


You need to program it. Here is how you doit.
Step by step:

1- get inside and lock all door with the "power dool lock switch"
2- insert the key into the ignition 6 times "IN and OUT" nice and steady until your hazards flash on dashboard. You can just keep inserting the key until you see the hazards flash, but 6 times should do it / get you into the program mode.
3-once the hazards flash, turn the key to ACC position (dash light up, but car is not running)
4-press any button on the remote (hazards should flash)
5-turn key OFF
6-remove key
7-unlock door with "power door lock switch"
8-open door DONE.
Good luck

Oct 14, 2008 | 2003 Nissan Maxima

3 Answers

Key fob not working


hello mate.. if it has stopped working you might want to check the battery first.. if you are sure that the battery is fine then consider reprogramming the fob to your car.. here are the steps to follow.. NISSAN

Remote Control Fob Procedures:

The Central Door locking is controlled by the Multi-Remote Control system which controls
the door locking, door super locking and emergency hazard reminders.

When the doors are locked and unlocked the unit flashes the hazard lights once for lock and twice for unlock.

A maximum of four remote controls are allowed to be programmed:

ALMERA
ALMERA TINO
PRIMERA
MAXIMA
MICRA
SERENA
VANETTE CARGO
TERANO II

Ensure all the doors have been unlocked, either by using a good transponder key or remote
control plip key.

Procedure:
1. Turn the ignition switch from Position 0 to ON 6 times within 10 seconds.
2. Next, turn ignition switch to OFF position. Leave key in ignition switch.
3. Wait 2 seconds then the system will enter programming mode and will flash the warning
lights twice.
4. Press and HOLD the unlock button on the Plip.
5. While pressing the unlock button, press the lock button 3 times.
6. Release the unlock button.
7. The warning lights will flash once to indicate successful programming.
8. Repeat procedure 4 to 7 for up to 4 plip key's.
9. When completed turn ignition ON, and the warning lights will flash 2 times.
10. Remove key, and check all plip key's for operation.
NOTE : The programming mode will stop when either the ignition is switch ON, 4 plip keys
have been programmed or no input signal either from the switch or plip keys has been received
for 120 seconds.


http://www.autokeysquad.com/nissan-fob-programming



i hope this can help you.. :)

Jul 28, 2008 | 2005 Nissan Sentra

1 Answer

Keyless entry keylob want lock or unlock doors or trunk.change battery and checked all fuses.


You need to program the remote. Get in to the car and LOCK all doors with the switch on drivers side door. Take the key and insert it into the ignition cylinder in and out 6-10 times, until the flashers/hazards flash on your dash board. Or just keep putting the key in and out (nice and easy now, not fast) until you see the lights on dash flash. After the lights flash, turn the key into ACC mode to make the whole dash light up.(do not start car) .With the key in ACC position, hit any button on remote, that will make the hazards flash again. Turn key off and unlock door with switch again. Open door.DONE.
Good luck.

Jul 15, 2008 | 2001 Nissan Altima

Not finding what you are looking for?
2005 Dodge Dakota Logo

158 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...