Question about 2000 Isuzu Rodeo

1 Answer

Dead OBD connector on 2000 Isuzu Rodeo

State inspection tech says OBD/DalaLink connector on 2000 isuzu rodeo isn't giving any signals. What to check and where. Have already checked all readily accessible fuses and connectors. Thanks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 437 Answers

The only reason I have ever seen for a dead OBDII or DCL while the car still runs is that the ECM has failed and for some reason just marginally functioning enough to appear normal. This is more common than one would think.

I would start by getting even a generic OBDII reader to confirm your work, then pull the battery connections and unplug the ECM from the harness and make sure visually that the conector has no obvious issues then reassemble and retest.

Posted on May 30, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the obd port on my 1993 isuzu rodeo


Depending on the model, you may have a GM style connector mounted on the bottom of the dash near the steering column, or you may have a 3 wire pigtail hanging near the parking brake pedal.
1996 and newer models use the OBDII style connector.

Aug 26, 2014 | 1993 Isuzu Rodeo

1 Answer

Check engine light P336


Are you sure this isn't P0336, P336 is not a vaild code not enough numbers.
P0336 ISUZU - Crankshaft Position Sensor Performance
Possible causes- Crankshaft position sensor harness is open or shorted
- Crankshaft position sensor circuit poor electrical connection
- Faulty crankshaft position sensor
- Signal plate may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead or weak battery Tech notes Sometimes and in some models, low battery voltage or a weak starter can can trigger a Crankshaft Position Sensor code. Before replacing any parts, recharge or replaced battery

Sep 07, 2012 | 2000 Isuzu Rodeo

1 Answer

Where are the connecters at for checking codes located for a 1997 rodeo with a 3.2 motor and auto trans?


For 1997 Isuzu Truck Rodeo 2WD 3.2L MFI SOHC 6cyl the OBD Diagnostic Link Connector is located: Front seating area, driver side, under dash, mounted above kick panel.

Hope this helps (remembert to rate and comment this answer).

Jul 12, 2011 | 1997 Isuzu Rodeo

1 Answer

Where is the obd connector on a 1995 3.2l isuzu rodeo, what kind of odb is?


maybe on a hump in front of the console, on the drivers side and may be covered with carpet. Or near the drivers left foot rest and drivers door underneath some plastic.

May 02, 2011 | 1995 Isuzu Rodeo

1 Answer

Owners manual for 2000 isuzu rodeo


Please check these link for help;

www.motors.shop.ebay.com/?_newu=1&_sop=1&_???nkw=isuzu+rodeo+manual&_???dct=1

www.car-stuff.com/mmparts/???isuzu-rodeo/repair_???manual.html

Sep 29, 2010 | Isuzu Rodeo Cars & Trucks

1 Answer

1993 Isuzu Rodeo


Have a look under the front of the transmission column/dash near the pedals. theyre usually there, tucked behind the trim. Not attached to anything, just on the end of wires. And you usually need a Tech-II diagnostics machine for any Isuzu kit, as even the likes of Snap-on won't read it.
:(

Jul 11, 2009 | 1993 Isuzu Rodeo

2 Answers

Obd code 1627 ,1999 4 cylinder isuzu rodeo


If P1627 is set when there is a problem with the fuel level sending unit, 100% sure on this problem, replace the fuel level sender in the gas tank, about 2.5 hours, very straight forward job

Jun 02, 2009 | 1999 Isuzu Rodeo

2 Answers

2000 isuzu Rodeo wont start


Could be your neutral safety switch, or it's not all the way in park. Broken or loose wires in the starting circuit. Inspect all wires and connectors at the battery, starter solenoid, and ignition switch. Or your starter pinion is jammed in the ring gear. Remove starter and inspect. Last but not least, your engine is seized. You don't want that one. Good luck.

May 22, 2009 | 2000 Isuzu Rodeo

2 Answers

Isuzu Tune up


Spark plugs every 100,000 miles, air and fuel filter 30,000 miles, inspect ignition system components when plugs are changed, replace as necessary.

Mar 19, 2009 | 2000 Isuzu Rodeo

Not finding what you are looking for?
2000 Isuzu Rodeo Logo

Related Topics:

447 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...