Question about 1989 Toyota Camry

1 Answer

Extra injector on corona 1988 4 cyclinder not hooked up why and how to hook up?

How to get the fifth injector working on a Toyota corona 1988 2-SE with extra injector

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 58 Answers

I think you've been had, i've never heard of a 5th injector. you can always call the parts guys at a deler

Posted on May 30, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where does fuel line hook into motor in a 1988 toyota truck 4cylender


search comes up as a toyota 4 runner hi lux or 22r

if Carby ..side of the carby body
if EFI on the injector fuel rail

a6bb5f23-2480-4b08-919c-3a2bd6a0905f.jpg

May 02, 2016 | Toyota Cars & Trucks

1 Answer

Electronic fuel control


You may have a bad mass airflow sensor, throttle position sensor, crank sensor or a bad ecm (brainbox). You can take it to autozone, advance auto or orielly's and they will hook it up to their diagnostic tester for free.

Jan 27, 2013 | 1988 Chrysler Fifth Avenue

1 Answer

I WAS DRIVING ALONG, THE CAR SLOW UP AS IF I'M RUNNING OUT OF GAS. I PULL OVER IT SHUTS OFF AND I PUT IT IN PARK IT STARTS BACK UP, PUT IT IN GEAR AND WHEN I ACCELERATE IT SHUTS OF. REPLACEED THE FUEL...


Hi!!
Check fuel pump pressure. Borrow a Fuel Pressure Tester from AutoZone, Checkers or similar auto parts store, they will also provide the proper operating pressure of your fuel pump. Here is a diagram on how to hook it up.
1kbron_95.jpg

Good Luck! A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa.

Feb 15, 2011 | 1988 Chrysler Fifth Avenue

2 Answers

The code is # 1 cylinder miss fire. i replaced plugs and wirers still running bad but no code yet


check for spark at the coil, if its weak, or no spark, replace the coil pack.

Dec 03, 2010 | 2001 Ford Windstar

1 Answer

1988 chrysler 5th Ave. rear seat


Push in and up at the same time at the bottom front of the seat...you need to use some force. Before you start, peek under there with a flashlight and you will see the hooks. Seeing them will give you a better idea on how it comes out. (not hard once you do it a few times)

Sep 08, 2009 | 1987 Chrysler Fifth Avenue

1 Answer

Cold Starting


You have a cold start injector that is controled by coolant temp and more than likely the sensor, which is located center of intake, between #2 and 3 injector...it looks a bit like a reg. temp. sensor and will have either blue or black electrical harness connected to it. This sensor 'tells' the cold start sensor, a fifth injector for cold starting, when coolant is below a certain temp and gives extra gas. Try to find one at a junkyard, otherwise, www.getcoolparts.com about $80 new. Better yet, buy a Bentley manual and there's diagnostics using a multimeter on diagnosing specifically. I have an 88 but it is an N/A, not a turbo and is an 8v...if your's is a 16 valve, look for sensor in same spot but under fuel rail/injector area.

Sep 02, 2009 | 1988 Saab 900

1 Answer

Key broke off in my ignition


take a small stiff wire (paperclips sometimes work) and make a slight hook in one end....you may be able to work it past the broken piece in the cylinder and hook it and pull it out...it may take awhile, but it ususally works

Feb 08, 2009 | 1997 Toyota Camry

1 Answer

Fuel line diagram


try an autozone or a dealership they can print out the diagrams for you

Feb 02, 2009 | 1988 Toyota Pickup

1 Answer

My temp gauge does not work on my 1988 toyota camry


take it back to the tranny person and have them repair their mistake. its that easy.

Dec 04, 2008 | 1988 Toyota Camry

Not finding what you are looking for?
1989 Toyota Camry Logo

Related Topics:

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...