Question about 1994 Toyota Camry

1 Answer

Wheel bearing rear repair

Help

Posted by on

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 58 Answers

Well you should replace both of rear wheel bearings. most likly if one gose the other is about to.
what you do is
NOTE your bearing might be pressed fit. if you can't remove by hand you are going to need a shop.

1- remove the wheel and brake assembly,
2-remove axle flange from hub
3- bearing should be easyly pulled out.
4- clean out all old grase
5-pack new bearing full of new greas.***MUST DO*** put greas in your hand and scrap greas into the bearing till it come out the top.(or use bearing packing tool)
6- put the rest of the greas into the bearing retainer and reinstall.
7- YOU MSUT pre load the bearing after you put the bearing in and bolt holding it in you must pre load to 40 in'lbs then back of and hand tighten (or go tight 1/4 past, then back of 1/2 then tighten buy hand.

never stike the bearing with a hammer IT MAY EXPLODE

Posted on May 30, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What causes the rear tires to lean inward on a chrysler pacifica. 2005. Is it the wheel bearing.


If that is what it is,here is a link on how to remove and check it,while you have it jacked up,look at other components and see if anything is out of place. Repair Guides Rear Suspension Wheel Bearings AutoZone com Here's a link to a new one. Duralast Wheel Bearing Hub Assembly Rear DL512288 Read Reviews on Duralast... CHECK THIS LINK OUT FIRST. found this helpful answer from chrysler mechanic on JustAnswer com

Jul 08, 2017 | Chrysler Cars & Trucks

1 Answer

Procedure for replacing rear whl brgs on a 2003 escape awd


4-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake shoes
    • Rear halfshaft nut and loosen the halfshaft from the hub
    • Wheel hub and place it in a vise
    • Inner wheel bearing race from the hub
    • Antilock Brake System (ABS) sensor bracket and move the sensor aside, if equipped
    • Parking brake cable from the steering knuckle
    • Brake line from the wheel cylinder and support the knuckle
    • Lower shock absorber nut
    • Lower ball joint by holding the ball joint stud
    • Upper ball joint
    • Coil spring while noting the location of the insulator
    • Steering knuckle cam
    • Steering knuckle
    • Snapring and press out the outer wheel bearing race from the knuckle
      06017-esca-g92.gif

      Rear hub and bearing
      Click to Enlarge

To install:

  1. Install or connect the following:
    • New wheel bearing into the steering knuckle
    • Snapring to the knuckle
    • Wheel hub
    • Steering knuckle cam and hand tighten the bolt
    • Coil spring
    • Shock absorber lower nut. Torque the nut to 85 ft. lbs. (115 Nm) for 2002-04 models; 129 ft. lbs. (175 Nm).
    • Upper ball joint. Torque the nut to 76 ft. lbs. (103 Nm).
    • Lower ball joint. Torque the nut to 76 ft. lbs. (103 Nm). Align the steering knuckle cam and torque the bolt to 85 ft. lbs. (115 Nm).
    • Brake line to the wheel cylinder. Torque the brake line bracket bolt to 15 ft. lbs. (20 Nm) and the brake line fastener to 11 ft. lbs. (15 Nm).
    • Parking brake cable to the backing plate. Torque the bolt to 16 ft. lbs. (22 Nm).
    • ABS sensor bracket. Torque the bolt to 80 inch lbs. (9 Nm), if equipped
    • Halfshaft nut. Torque the nut to 214 ft. lbs. (290 Nm).
    • Brake shoes
    • Rear wheel
    • Negative battery cable
  2. Fill and bleed the brake system.
  3. Check and adjust the wheel alignment as needed.

2-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake drum
    • Wheel hub nut
    • Wheel hub
    • Inner wheel bearing race from the hub
    • Snapring
    • Wheel bearing outer race from the knuckle
      06017-esca-g92.gif

      Rear hub and bearing
      Click to Enlarge 06017-esca-g93.gif

      Rear hub removal
      06017-esca-g94.gif

      Inner wheel bearing removal-rear hub/bearing
      06017-esca-g95.gif

      Rear wheel bearing removal-2wd
      06017-esca-g96.gif

      Rear wheel bearing removal-4wd

To install:
Install or connect the following:

  • Wheel bearing in to the knuckle
  • Snapring
  • Wheel hub into the wheel bearing
  • Wheel hub nut. Torque the nut to 214 ft. lbs. (290 Nm).
  • Brake drum
  • Rear wheel
  • Negative battery cable
    06017-esca-g97.gif

    Rear wheel bearing installation
    06017-esca-g98.gif
    hope this helps if so send testimonial comment or even any other questions you have

Jan 16, 2011 | Ford Escape Cars & Trucks

1 Answer

Rear wheel bearing is out, how easy to repair


not easy,you will probably need a hydraulic press to remove and reset the bearings

Apr 20, 2010 | 2002 GMC Yukon Denali

1 Answer

I need to change the rear wheel bearing assemblies on my 2003 Lincoln Aviator. I have replaced the front already and would like to know if the procedure for the rear is different since the rear wheel...


yes, the rear is much different...you can get good help on the ford forums, you can downld help guides online at autozone.com ...join up to access their repair guides...its fee and safe...there are other auto pts houses that offer this service....

Mar 03, 2010 | Lincoln Aviator Cars & Trucks

2 Answers

How to replace rear wheel bearings


don't have topaz. maybe escort will help guide you.

Section 04-02: Suspension and Wheel Hubs, Rear 1996 Escort, Tracer Workshop Manual
REMOVAL AND INSTALLATION Wheel Bearing and Hub Assembly NOTE: Wheel bearings are not serviceable and should therefore be replaced as an assembly with the wheel hub (1104).

Removal
  1. Raise and support the vehicle.
  1. Remove the wheel and tire assembly.
  1. Remove the hub grease cap (1131) from the wheel hub.
  1. If equipped with disc brakes, remove the rear disc brake caliper (2552) and rear disc brake rotor (2C026). Refer to Section 06-04 for the removal procedure.
  1. If equipped with drum brakes, remove the two brake drum screws and the brake drum (1126).
  1. Unstake the rear axle wheel hub retainer (4B477) securing the wheel hub to the rear wheel spindle (4A013). Remove and discard the rear axle wheel hub retainer.
  2. Remove the wheel hub from the rear wheel spindle.

Feb 06, 2010 | 1990 Mercury Topaz

3 Answers

Right rear wheel wobbles as well as there is a


From what you describe it likely is a very bad axle bearing. I would recommend not driving until repaired.

Oct 31, 2009 | 2000 GMC Jimmy

1 Answer

Rear whheel bering repair


need to find rear wheel bearing isuzu bighorn 3.1 (*** import)

Oct 28, 2009 | 1985 Isuzu Trooper

1 Answer

Loose rear wheel, believe it is the bearing. How do I repair it?


drum brakes you remove rear wheel- speed sensor-grease cap-flange nut-outer bearing-brake drum-inner grease seal-inner bearing-drive the bearing races out of the drum hub.to install -install the inner and outer bearing races.apply grease to the bearings and hub cavity.then you install the inner bearing -inner grease seal-brake drum-outer bearing-flange nut torque it to 159 to 192 ft lbs. THE REAR DISC BRAKE WHEEL BEARINGS-you have to remove rear wheel -wheel speed sensor-brake caliper and rotor-rear axle hub bolts-tone the wheel with tool 09445-21000-carrier assembly-nut after unstaking it-press out the rear axle hub-remove the bearing inner race with tool 09445-21000-remove the bushings from the carrier with tools 09453-33000b and 09545-21100.to install -press in the bushings to the carrier with tools 09453-33000b and 09545-21100- press in the bearings to the hub with tool 09221-21000.tighten the flange nut to meet the concave portion of the spindle-press in the tone wheel with tool 09221-21000-torque the nut to 191 ft lbs -install the hub and bearing assembly to the backing plate and torque the bolts to 88 ft lbs-install the brake caliper and rotor.install the wheel speed sensor if equipped.install the rear wheel.TO BUY THE TOOLS TO DO THE JOB.LOOK UP KENT MOORE TOOLS ON INTERNET.

May 30, 2009 | 1999 Hyundai Sonata

2 Answers

Nissan sentra gxe 03 rear wheel hub bearing problem


Easy job ! just rem to get a gear puller for the antilock gear and install same as came off old one Parts around 100$ each apx 1/2 hr each side

Jun 12, 2008 | 2003 Nissan Sentra

Not finding what you are looking for?
1994 Toyota Camry Logo

283 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...