Question about 2006 Hyundai Tucson

2 Answers

Rear brakes (driver-side) squeal after replacing rotors and pads

I just replaced the rotors and pads on the front and rear of my 2006 hyundai tuscon....the back driver side squeals all the time while driving. What could be the problem. I replaced the rear rotors and pads first, then still noticed a squealing, so I thought I might as well do the front....still getting a squeal fron the rear driver side all the time while driving. Do I need to put anti-squeak compound on the pads? I noticed that the new rotors are not all shiny. Only about half of the rotor (inside) is shiny, the outer part orf new rotor is rusty....bad pads ?

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 52 Answers

You need to grease the metal clips at the top and bottom of the pads (dont get grease on the rotor or pad though) and also spray some "disc brake quiet" on the back of the pads. it comes in a red can and the spray that comes out is like sticky red paint. do those 2 things and the squeals will be gone.

Posted on May 30, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,486 Answers

Rear brake calliper not releasing.semi seized

Posted on May 30, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I forgot where my wear indicator goes on my brake pads. 2006 Impala LT 3.9


If your talking about the squeal tabs on the brake pads. Always on the caliper side. Front and back.

Feb 27, 2016 | Cars & Trucks

1 Answer

2006 HYUNDAI Sonata I figured I'd bleed the the rear brakes after replacing the rotors and pads. 120,000 Miles with no previous brake issues besides normal replacement of front rotors and pads. After...


Try re-bleeding ALL wheels starting with furthest away - pass rear, then driv rear, then pass front and driv front. That should get your pedal back. To reset light you need ABS reset tool and it's EXPENSIVE. Have a good competent shop reset it for you. Body shops can reset them also.

Feb 27, 2011 | 2006 Hyundai Sonata

2 Answers

How to change brake pad and check rotors


Brake Pads Removal & Installation Front for_car_toy_cam_02-04_sst_frt_dsc_asm.gif

To Remove:
  1. Drain brake fluid to ½ full level in reservoir.
  2. Remove the front wheels. toy_car_cam_frontbrakepads.gif

  3. Remove the front brake caliper assembly.
  4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
  5. Remove the wear indicator from each of the 2 brake pads.
To Install:
NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.
toy_car_cam_frontbrakepads.gif

  1. Using a large C clamp or equivalent press piston into the caliper.
  2. Apply disc brake grease to the inside of each anti-squeal shim.
  3. Install the anti-squeal shims on each pad.
  4. Install the pad wear indicator clip to the pads.
  5. Install the pads with the pad wear indicator plate facing upward.
  6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
  7. Install the front wheels.
  8. Fill the master cylinder with new clean brake fluid.
  9. Pump the brake pedal several times to seat the brake pads.
Rear TMC made rear brake components toy_car_cam_tmcrearbrakes.gif

TMMK made rear brake components toy_car_cam_tmmkrearbrakes.gif

To Remove:
  1. Drain the brake fluid to ½ full level in reservoir.
  2. Remove the rear wheels.
  3. Remove the caliper slide pins.
  4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
  5. Remove the rear brake calipers.
  6. Remove the 2 brake pads with the anti-squeal shims.
  7. Remove the anti-squeal shims and pad wear indicators from brake pads.
To Install:
  1. Using a large C clamp or equivalent press the piston into the caliper.
  2. Coat both sides of the outer anti-squeal shim with pad grease.
  3. Install anti-squeal shims to each pad.
  4. Install wear indicators on the 2 brake pads.
  5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
  6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
  7. Fill the master cylinder with new clean brake fluid.
  8. Pump the brake pedal several times to seat the brake pads.
  9. Install the rear wheels.
prev.gif next.gif Brake Rotor Removal & Installation Front To Remove:
  1. Remove the front wheels.
  2. Remove the front brake caliper assembly.
  3. Remove the front brake pads.
  4. Remove the 2 bolts and caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the front wheel disc.
To Install:
  1. Align the match marks and install the front disc.
  2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
  3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the front wheel.
Rear To Remove:
  1. Remove the rear wheels.
  2. Remove the brake caliper assembly.
  3. Remove the brake pads.
  4. Remove the 2 bolts and the caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the rear disc.
To Install:
  1. Align the match marks and install the rear disc.
  2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
    • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
    • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
  3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the rear wheel
prev.gif next.gif

Jan 25, 2011 | 2007 Toyota Camry

1 Answer

What tools needed to replace front brake pads & rotors


Brake Pads
Removal & Installation
Front





3.4L front disc brake assembly
toy_4run_34_frontbrakeassembly.gif








4.0L and 4.7L front disc brake assembly
toy_4run_frontbrakeassembly.gif



To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Clip, 2 caliper pins, the anti-rattle spring then remove the 2 brake pads
      and the 4 anti-squeal shims

To Install:

CAUTION
Only replace brake pads on 1 side of the
vehicle at a time. Failure to use this procedure could cause the caliper pistons
on the opposite side of the vehicle to pop out requiring the reconditioning or
replacement of the brake caliper.


  1. Remove a small amount of brake fluid from the master cylinder.
  2. Install a used brake pad into the caliper and compress the caliper pistons.
  3. Apply disc brake grease to both sides of the inner anti-squeal shims.
  4. Install or connect the following:

    • Anti-squeal shims to the new brake pads
      NOTE: When replacing worn pads, the anti-squeal shims must be replaced
      together with the pads.

    • 2 brake pads
    • Anti-rattle spring and the 2 caliper pins
    • Clip
    • Front wheel

  5. Depress the brake pedal several times to seat the brake pads.
  6. Check the brake fluid level and top off as needed.

Rear
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Rear wheel






      toy_4run_rearcalbolts.gif



    • 2 cylinder slide pins from rear caliper assembly
    • Caliper assembly from rear caliper mounting
    • 2 brake pads with anti-squeal shims from rear caliper mounting
    • 2 anti-squeal shims from each disc brake pads
    • Pad wear indicator plate from the inner side disc brake pad
    • 4 pad support plates from the rear caliper mounting

To Install:


  1. Install or connect the following:

    • 4 pad support plates on the rear caliper mounting
    • Pad wear indicator plate on the inside brake pad
      Note: Install the pad wear indicator facing downward.

    • Anti-squeal shims on each brake pad
    • 2 disc brake pads with anti-squeal shims to the caliper assembly

  2. Apply lithium soap base glycol grease to the sliding part of 2 caliper slide
    pins.
  3. Install or connect the following:

    • Disc brake caliper assembly with 2 caliper slide pins
    • Torque to 65 ft-lbs (88 Nm)
    • Rear wheel

  4. Depress the brake pedal several times to seat the brake pads.
  5. Check the brake fluid level and top off as needed.
--- Removal & Installation
Front
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Front brake caliper assembly

  3. Make matchmarks on the disc and the axle hub.
  4. Remove the front disc.

To Install:


  1. Align matchmarks and disc onto axle hub.
  2. Install or connect the following:

    • Front brake caliper assembly with the 2 bolts

      1. Torque to 90 ft-lbs (123 Nm)

    • Front wheel

Sep 23, 2010 | 2003 Toyota 4Runner

1 Answer

I have a crunching sound coming from the front wheels when applying the brakes at a low speed and only after I drive the car a few miles


sounds like the pads have worn down, or there's debris between the pads & rotor. in my personal experience, the stock rotors from hyundai don't hold up very well. i replaced pads (front and rear) at around 45K miles, and had the stock rotors turned down. less than 1K miles later, the front rotors were already warped! there have been many complaints about hyundai's rotors, so i replaced mine with a set of raybestos rotors and also put ceramic pads up front. 20K miles later, they're still working great.

Feb 05, 2010 | 2006 Hyundai Sonata

2 Answers

Brake squeal


You, Probably will, Brake Squeal is NOT a new problem.
Disc brake's have been Squealing since, They, became
factory installed on chevrolet in 1971. Before, that they,
were a option. In 72 they even had a bulleton how, to
FIX it. And, no it didn't work.
With That said, Any time you replace Brake pads you,
should always re-surface the Rotors.
Why? First you may start to notice a pulsation as the
pads ware (sometimes! ) The best way to avoid, brake
squeal is to manchine the Rotors put, the blue membrain
sealent on the back side of the pads. And hope that works!!
Some brakes Pads squeal JUST SQUEAL??
You, Could do the same Brake job the same as you did
this one and, they may NOT Squeal.WHY, I WISH I NEW. They
sell all types of STUFF to stop Brake noice DON'T waste your $$.

Jan 31, 2010 | Chevrolet 3500 Cars & Trucks

1 Answer

Squealing sound - front driver's side brakes


This sounds like a wear indicator( a metal tab on the brake pad) is doing its job, warning you that the brake pads need replacement soon. you can bend the wear indicators away from the rotor so they won't make contact. This will stop the annoying noise. Replace the pads and check the brakes soon. Brake pads should always be changed on both wheels at thge same time, so change the other front pads also.

Nov 27, 2009 | 2002 Kia Sportage

2 Answers

I just replaced both front rotors and pads, along with the driver side caliper. My next step is to now bleed the brakes. my question is do i need to bleed all 4 brakes or just the 1 that was replaced?


you don't need to bleed front brakes if you only did rotors and pads. If you look at the master cylindar, there are 4 lines coming off of it, one for each brake. Only bleed what you replaced.

Sep 29, 2009 | 2002 Hyundai Accent

1 Answer

Constant squeal in brakes,


Front or rear brakes?
Make sure the rotor isn't contacting the backing dust plate.
Make sure the brake pad slider clip/clips are not contacting the rotor.

Mar 28, 2009 | 2006 Hyundai Sonata

2 Answers

2005 Dodge Durango Front Brake Squeal


Did you buy factory pads or get cheap aftermarket pads? If aftermarket did you get the ceramic? The cheap aftermarket ones tend to squeal pretty bad. Like the last comment on here, you should have your rotors turned whenever you change the pads.

Jan 13, 2009 | 2005 Dodge Durango

Not finding what you are looking for?
2006 Hyundai Tucson Logo

1,182 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

77514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8826 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...