Question about 1999 Chevrolet Blazer

1 Answer

Rear windshield wiper connection

Ok the problem start with the windshield wiper, the arm arms coonection on outside working but the solution is running down the indside of my door panel, trying to figure out how to re-connect. cant find anything or anybody to help.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Chevrolet Master
  • 3,854 Answers

You need to open the rear glass from the rear hatch. Look inside where the glass latches to the rear hatch. There is a Phillips head screw that connects the rear inner plastic panel to the rear hatch, remove this screw. Now, in the strap that you use to pull the rear hatch down, there is a torques head screw, that holds this strap to the rear hatch, you need to remove this screw.
Start at one of the outer corners of the inner plastic panel and pull the panel away from the hatch. You will see the upper wiper motor in the right hand corner of the hatch. ther is one connector that is easy to see, you have to pull up on a plastic clip to remove this connector. Look for the rubber hose for the windshield washer fluid, it may be cracked or fallen off the plastic nozzle to the outside of the rear door.

Please the hose back on or replace the hose if it's cracked or damaged by the wiper motor. To install just follow the procedure in revers.
Good luck and hope i made some sense. Keep me posted, be glad to help out.

Posted on May 30, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Rear windshield wiper does not cover the intended area how to remove rear windshield wiper arm


IF YOU HAVE A PLASTIC CAP ON ARM REMOVE IT AND THE NUT UNDER IT, AND LIFT WIPER ARM OFF.

Jan 02, 2011 | 2000 Dodge Caravan

1 Answer

Where is the wiper motor on my 1999 GMC Yukon?


Windshield Wiper Motor
Removal & Installation
To Remove:


  1. Remove wiper arms.
  2. Remove weatherstrip from cowl.
  3. Remove two cowl vent grille panel screws.
  4. Remove windshield nozzles and hoses.
  5. Remove three cowl vent grille panels.
  6. Disconnect windshield wiper motor electrical connector.
    NOTE: Do not remove crank arm from windshield wiper motor.

  7. Loosen nuts that attach the drive link brackets to the crank arm.
  8. Remove wiper motor crank arm brackets.






    gm-06-00-1079.gif



  9. Remove three bolts and windshield wiper motor from vehicle.

To Install:


  1. Install windshield wiper motor and three bolts.

    • Torque to: 62 in lbs. (7 Nm)

  2. With right side linkage closest to the windshield wiper motor, install drive
    link brackets to wiper motor crank arm.

    • Torque nuts to: 44 in lbs. (5 Nm)

  3. Connect electrical connector.
  4. Install nozzles and windshield washer hoses to cowl vent grille.
  5. Install three cowl vent grille panels and screws to vehicle.
  6. Install weatherstrip to cowl.
  7. Install wiper arms.


prev.gif next.gif

Oct 30, 2010 | 1999 GMC Yukon

1 Answer

I need to adjust the wiper arm on a 1997 suburban, it hits the side of the window.


Wiper Arm & Blade (Front) Removal & Installation Wiper Blade To Remove:
  1. Turn ignition switch to ACCY position.
  2. Turn wiper switch to PULSE position and turn ignition OFF when wipers are stopped in the innerwipe position.
  3. Push the wiper blade clip button IN and remove wiper blade from wiper arm.
To Install:
  1. Insert wiper arm hook through opening in wiper blade.
  2. Place wiper blade pivot in the inside radius of wiper arm hook.
  3. Pull on wiper blade pivot into hook until it locks into place.
  4. Check wipers for proper operation.
Wiper Arm To Remove:
NOTE: Mark position of wiper blade on windshield to ensure proper position upon reassembly.
  1. Remove washer hose.
  2. Lift wiper arm from windshield and use a screwdriver to disengage retaining latch.
  3. Remove wiper arm from shaft.
To Install:
  1. Place wiper arm on shaft so that wiper arm aligns with marks placed on windshield.
  2. Press arm assembly on shaft and push retaining latch IN.
  3. Connect washer hose.
  4. Remove windshield markings and check wipers for proper operation.
prev.gif next.gif

Oct 26, 2010 | Chevrolet Suburban 1500 Cars & Trucks

1 Answer

Wipers will not move, makes noise and there is power to the motor. Motor was replaced. Someone told me that the arms probably moved to far and are now stuck, how do I fix this?


Windshield Wiper Blade & Arm Removal & Installation Front To Remove:
  1. Mark the location of the wiper on the windshield.
  2. Remove or disconnect the following:
    • Nut cover
    • Nut from the wiper arm
    • Wiper arm
Wiper arm mounting nut gm_truck_s10_w-wpr-arm_ret-nt.gif
To Install:
  1. Install or connect the following:
    • Secure the wiper arm with the nut.
      1. Tighten to: 17 ft-lb (23 Nm)
    • Nut cover
Rear To Remove:
  1. Put the wiper arm in the park position.
  2. Remove or disconnect the following:
    • The washer hose from the connector
    • The cap from the wiper arm
    • The nut from the wiper arm
    • The wiper arm from the wiper motor shaft
Rear wiper arm mounting nut gm_truck_s10_w-wpr-arm_ret-nt_rr.gif
To Install:
  1. Install or connect the following:
    • The wiper arm on the wiper motor shaft in the park position with the wiper arm resting on the park ramp
    • The nut on the wiper arm
      1. Tighten the nut. Torque to: 17 ft lbs (23 nm)
    • The cap on the wiper arm
    • The washer hose on the connector

---
The wiper motor hopefully is ok, but if the wiper arms were not mounted at the right spot, it could have damaged the motor as it returned to the rest position, unfortunately.

If there is noise, the noise could be coming from the wiper arm joint being stripped out or the motor itself assuming that the ball joints under the hood and behind the firewall are still connected.

Check these items, and I'm sure you will get to the bottom of this.

Good luck on this repair.

Oct 08, 2010 | 1997 Chevrolet Blazer

2 Answers

I have one wiper that does not work the other stops in the middle of the windshield how can i fix them


The motor could be bad, but it's likely that the ball joint connections under the hood area under the cowl have become disconnected for the one windshield wiper arm.

The connection of the arm that moves should be checked for being at the correct angle for parking.
Removal & Installation 2000-03 Wiper Motor and Bushing Replacement L4-2.2L (Vin F) & V6-3.0L (Vin R) To Remove:
sat_car_22_fw-wpr_arm_xp.gif

  1. Before servicing the vehicle refer to the precautions at the beginning of this section
  2. Remove the wiper arm finish caps
  3. Mark both wiper arm positions on the windshield by using a wax pencil or tape
  4. Remove or disconnect the following:
    • Wiper arm retaining nuts and washers
    • Wiper arms
    • Weather-strip at rear of hood sat_car_22_f_wshd_wthr-strp.gif

      sat_car_22_f_wshd_gril_nts.gif

    • Grill nuts from base of wiper arm shaft
    • Grill
    • Electrical harness connector from the wiper motor
    • Wiper motor retaining bolts
    • Wiper motor assembly from plenum area
    sat_car_22_f_wpr-mtr_asy.gif

    sat_car_19_wpr_mdl_rmv.gif

  5. If replacing wiper module bushings remove the steel bushing first then the rubber grommet
  6. Remove the wiper motor from the transmission assembly
To Install:
  1. Install or connect the following:
    • Wiper motor to transmission assembly NOTE: If the wiper module bushings were replaced install the rubber grommet first then the steel bushing.
    • Wiper motor to plenum area
    • Wiper motor retaining bolts; torque to 44 lb-in. (5 Nm)
    • Electrical harness connector to the wiper motor
    • Weather-strip at the rear of hood
    • Grill
    • Grill nuts to the base of the wiper arm shaft
  2. Install the wiper arm assemblies at the marks made during removal or at the PARK position if a new wiper motor is installed
  3. Install the wiper arm retaining washers and nuts; torque to 9 lb-ft. (12 Nm)
  4. Install the wiper arm finish caps
  5. Verify correct wiper system operation
prev.gif next.gif

Oct 05, 2010 | 2001 Saturn L-Series

1 Answer

I installed a new wiper motor. I ran it before installing the wiper arms. it will not stop at zero. it over travels down into the cowling. I try to rest them higher then they stop some where in the middle...


Try to run the motor without the wiper arms tightened down and turn it off so it can cycle down to its rest state. Then install the wiper arms.

Make sure, that the car's windshield wiper wiring is correct for this motor.
---
Wiper Arm & Blade Removal & Installation Front To Remove:
CAUTION
When the wipers are parked (off), the driver’s wiper arm must be above the passenger’s wiper arm.
  1. Remove the clip holding the outside end of the wiper arm cover to the arm.
  2. Lift the arm cap up to expose the nut.
  3. Remove the wiper arm mounting nut.
  4. Using a suitable two jaw puller, remove the wiper arm from the wiper pivot.
To Install:
  1. Verify that the wiper motor and linkage are in the parked position.
  2. Place the wiper arm in position over the wiper pivot.
  3. Install the nut to hold the wiper arm to the wiper pivot. Torque nut to 26 ft. lbs. (35 Nm). CAUTION
    Make sure to tighten the wiper arm nut properly.
  4. Push the arm cap cover down.
  5. Secure the clip holding the cover to the wiper arm.
Rear To Remove:
  1. Lift and hold the wiper arm away from the rear window.
  2. Lift the lock securing the wiper arm to the pivot.
  3. Slowly release the wiper arm so it rests against the lock.
  4. Remove the wiper arm from the pivot.
To Install:
  1. Install the wiper arm on the pivot.
  2. Pull the arm outward and release the lock.
  3. Gently release the wiper arm until it rests on the rear window.
prev.gif next.gif

Aug 22, 2010 | 1996 Dodge Grand Caravan

1 Answer

Removing rear windshield wiper arm on 94 4Runner


on the wiper arm, there is a cap. remove cap and there is a nut underneath, remove nut spray wd40 oil on the threads that are exposed, then slowly wiggle arm and pull simultaneously to remove.

Jun 11, 2010 | 1994 Toyota 4Runner

1 Answer

Windshield wiper for rear window does not work we can hear a clicking sound come from the motor of the rear windshield wiper


If you hear a clicking sound, then you know you have power. Check to see if the motor arm is moving any at the wiper arm.The small cap that covers the wiper arm to motor can be pulled apart, to see if the nut is loose or if the gear housing is stripped on the wiper arm, or if the motor drive is stripped. These are say to check and are cost effective for you.

Feb 16, 2010 | 2002 Chevrolet TrailBlazer

1 Answer

The wiper motor on my 1983 Ford Ranger still works but the wipers no longer move. I think there is a failure of the mechanical linkage. Where do I go to find repair parts?


why do you think the motor still works if the wipers don't move? Can you hear the motor run or can you see a little movement when you turn the switch on?

What happens when you activate the washers?

go to a salvage yard that allows you to remove the parts yourself. Then you can see how the motor and linkage assembly comes out.


don't have 1983 info, but here is 1994:

Section 01-16A: Wiper and Washer System, Ranger/Explorer 1994 Ranger and Explorer Vehicles Workshop Manual
DESCRIPTION AND OPERATION Windshield Wiper System, Ranger/Explorer The windshield wipers are actuated by a permanent magnet, rotary-type electric windshield wiper motor (17504) . The two windshield wiper pivot arms (17526) and windshield wiper blades (17528) are mounted on a pivot shaft, one at each side of the windshield. The windshield wiper mounting arm and pivot shaft (17566) are connected to the motor by windshield wiper adapter and connecting arm clip (17531) . Ranger and Explorer vehicles are equipped with an interval wiper and washer (IWW) system featuring a lever-type turn signal and windshield wiper switch (13K359) mounted on the steering column. The IWW windshield wiper governor (17C476) uses a relay contact to control current to the windshield wiper motor . The governor electronic circuitry controls the contact to supply current to windshield wiper motor . A rear wiper/washer system is available on Explorer vehicles. The rear window wiper system consists of a windshield wiper motor mounted inside the liftgate (40010) , an articulating windshield wiper pivot arm and windshield wiper blade , a windshield wiper/washer switch (17A553) and an inline circuit breaker. The front electric windshield washer system consists of a control switch, integral with the turn signal, a windshield washer reservoir (17618) and windshield wiper motor and the necessary windshield washer hoses (17A605) , windshield washer nozzle jet and brackets (17603) and attaching parts.
------------------------------------------------------------------------------------------------
Pivot Shafts and Linkage Removal and Installation
NOTE: The left and right pivot and windshield wiper adapter and connecting arm clip assemblies are serviced separately.
  1. Perform Steps 1 through 9 of Windshield Wiper Motor Removal as described in this section.
  1. If servicing left windshield wiper adapter and connecting arm clip , remove left windshield wiper mounting arm and pivot shaft and windshield wiper blade assembly.
  1. Remove left windshield wiper adapter and connecting arm clip access cover.
  1. Remove left pivot nut, lower windshield wiper adapter and connecting arm clip and slide it out through left access opening. For installation, follow removal procedures in reverse order. Tighten nut to 10-13 Nm (7-10 ft-lb). Make sure the clip is fully seated in the windshield wiper adapter and connecting arm clip . Do not try to install clip with windshield wiper adapter and connecting arm clip on motor crank pin.
----------------------------------------------------------
Windshield Wiper Motor Windshield wiper motor are not serviceable. If worn or damaged, the windshield wiper motor must be replaced as an assembly. Removal
  1. Cycle windshield wiper blades until in straight-up position and turn ignition switch OFF.
  1. Disconnect battery and wiper motor electrical connector.
  1. Remove the right windshield wiper mounting arm and pivot shaft and windshield wiper blade .
  1. Disconnect the battery ground cable (14301).
  1. Remove the right pivot nut and allow the windshield wiper adapter and connecting arm clip to drop into the cowl top outer panel .
  1. Remove the linkage access cover, located on the right side of the dash panel near the windshield wiper motor.
  1. Reach through the access cover opening and unsnap the wiper motor clip.
  1. Push the clip away from the windshield wiper adapter and connecting arm clip until it clears the nib on the crack pin. Then, push the clip off the windshield wiper adapter and connecting arm clip.
  1. Remove the windshield wiper adapter and connecting arm clip from windshield wiper motor crank pin.
  1. Remove nut and ground strap.
  1. Remove three attaching nuts from windshield wiper motor. Remove the windshield wiper motor .
Installation
  1. Position the windshield wiper motor and install the three attaching screws. Tighten to 13.6-19.0 Nm (10-14 ft-lb).
  1. Install nut and ground strap.
  1. Connect wiper motor electrical connector.
  1. Install clip completely onto right windshield wiper adapter and connecting arm clip. Make sure the clip is fully seated. Do not put the windshield wiper adapter and connecting arm clip on the motor crank pin and then try to install the clip.
  1. Install the left windshield wiper adapter and connecting arm clip onto the wiper motor crank pin.
  1. Install the right windshield wiper adapter and connecting arm clip onto the wiper motor crank pin. Pull the windshield wiper adapter and connecting arm clip onto the crank pin until it snaps into place. The clip is properly installed if the nib is protruding through the center of the clip.
  1. Install the right windshield wiper mounting arm and pivot shaft and nut. Tighten the nut to 9.5-12.5 Nm (84-110 in-lb). NOTE: When the battery has been disconnected and reconnected, some abnormal drive symptoms may occur while the powertrain control module (PCM) (12A650) relearns its adaptive strategy. The vehicle may need to be driven 10 miles or more to relearn the strategy.
  1. Connect the battery ground cable and turn the ignition switch on. Turn turn signal and windshield wiper switch off so windshield wiper motor will park, then turn ignition switch off. Replace right windshield wiper adapter and connecting arm clip access cover.
  1. Install the windshield wiper mounting arm and pivot shaft and windshield wiper blade assemblies on the pivot shafts to dimension X. Dimension X is the distance between the centerline of the blade saddle and the top edge of the cowl top outer panel grille. The value of Dimension X for each vehicle is given in the Dimension X chart in the Specifications portion of this section.
  1. Test the system.
6bd608c.gif

Jan 04, 2010 | 1983 Ford Ranger

1 Answer

How to replace rear wiper arm 2004 toyota sienna


YO CAN HAVE TWO DIFFERENTE KIND IF YOU GOT A CAP ON IT THAT MEEN THERE A NUT THAT HOLDING THE ARM IN PLACE IF ITS THAT BE CAREFULL WHEN YOU REMOVE THAT NUT ITS VERY LITTLE NUT HOLDING IT IN PLACE AFTER USE PLIERS TO REMOVE ARM 2ND IF YOU DONT HAVE A CAP THAT MEAN ITS PRESSURE FIT THAT THE WORST LIFT THE ARM UNDER THERE A METAL CLIP MOVE THE CLIP OUTSIDE ME I SUDJECT YOU TO CUT WITH A SAW THE SIDE OF OLD ARM USE PLIERS TO REMOVE OLD ARM CLEAN THE WIPER SHAFT THE SPLINE ON IT AND REINSTALL IT GOOD LUCK PIERRE

Jan 10, 2009 | 1998 Dodge Durango

Not finding what you are looking for?
1999 Chevrolet Blazer Logo

496 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...