Question about 2004 Kia Sedona

2 Answers

Code P0350 Ignition Coil Primary/Secondary circuit 2004 Kia Sedona

I have a 2004 kia sedona 6cyl and about a week ago my car wouldnt start. After checking all of the fuses, the camshaff position sensor, main fuse and more. It was determined that the computer was not working. Went to a used parts place and picked up a computer for $100 put that in and it fixed about 65% of the problem. But still it wouldn't start. So I changed the ignition failure sensor and it starts but now it shakes a lot and the Diagnostic code it gives me is P0350 which is Ignition coil Primary/Secondary circuit. There is no spark at the middle coil. But when I move the middle coil to another spot there is spark. So I don't think the coil is messed up. Could it still be the computer?

Posted by on

  • arodcustomtr May 29, 2009

    What wire??? The wire to the coil?

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 323 Answers

It could be the computer, but it could also be the wire. You can check the resistance of that wire, or simply use a known good wire to see if that is what it is.

Posted on May 29, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have a 2004 Kia Sedona as well, it shakes, has blinking lights, powers off as well. I changed the alternator, battery, Full tune up, 3 new ignition coils and crank case sensor. What to do next?

Posted on Apr 21, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

P0351 code loss of power 2.3L08ford ranger,it warms slow and really need to eliminate1~voltage regulator is where?) & 2~ ground through PCM) 3~knowing limits&threashholds{sensorsIGNcircuit}?Ty 0$


P0351 loss of power ? That's not what this code is about . P0351 - Ignition Coil A Primary/Secondary Circuit ,you have a bad coil and possibly a bad coil driver inside the PCM . Do yourself a favor an take your vehicle to a qualified repair shop !
P0351 - Ignition Coil A Primary/Secondary Circuit Description: See the description for DTC P0350. Possible Causes: See the possible causes for DTC P0350. Diagnostic Aids: See the diagnostic aids for DTC P0350. Application Key On Engine Off Key On Engine Running Continuous Memory Coil-on-plug (COP) ignition testing - GO to Pinpoint Test JF . GO to Pinpoint Test JF . Coil pack ignition testing - GO to Pinpoint Test JE . GO to Pinpoint Test JE .
P0350 - Ignition Coil Primary/Secondary Circuit Description: Each ignition primary circuit is continuously monitored. The test fails when the powertrain control module (PCM) does not receive a valid ignition diagnostic monitor (IDM) pulse signal from the ignition module (integrated in the PCM). Possible Causes:
  • Open or short in the ignition START/RUN circuit
  • Open coil driver circuit
  • Coil driver circuit short to ground
  • Damaged coil
  • Coil driver circuit short to VPWR
Diagnostic Aids: Use the 12-volt non-powered test lamp to verify START/RUN voltage at the ignition coil harness connector.
Check the coil driver circuit for open, short to VPWR, or short to ground. Application Key On Engine Off Key On Engine Running Continuous Memory All GO to Pinpoint Test JE .

Feb 18, 2017 | 2008 Ford Ranger

2 Answers

I HAVE REPLACED THE COIL PACKS AND THE COMPUTER ON MY 2006 F150,BUT I STILL GET AN ERROR CODE OF 352.WHY IS THIS ?


P0352 - Ignition Coil B Primary/Secondary Circuit Description: See the description for DTC P0350. Possible Causes: See the possible causes for DTC P0350. Diagnostic Aids: See the diagnostic aids for DTC P0350. Application Key On Engine Off Key On Engine Running Continuous Memory Coil-on-plug (COP) ignition testing - GO to Pinpoint Test JF . GO to Pinpoint Test JF . Coil pack ignition testing - GO to Pinpoint Test JE . GO to Pinpoint Test JE .
P0350 - Ignition Coil Primary/Secondary Circuit Description: Each ignition primary circuit is continuously monitored. The test fails when the powertrain control module (PCM) does not receive a valid ignition diagnostic monitor (IDM) pulse signal from the ignition module (integrated in the PCM). Possible Causes:
  • Open or short in the Ignition START/RUN circuit
  • Open coil driver circuit
  • Coil driver circuit shorted to ground
  • Damaged coil
  • Coil driver circuit shorted to VPWR
Diagnostic Aids: Use the 12-volt non-powered test lamp to verify START/RUN voltage at the ignition coil harness connector.
Check the coil driver circuit for open, short to VPWR, or short to ground. Application Key On Engine Off Key On Engine Running Continuous Memory Coil pack ignition testing GO to Pinpoint Test JC . Coil-on-plug (COP) ignition testing GO to Pinpoint Test JB . Without me testing , it's hard to say what you got going on ! Coil packs ? What engine does it have ? 5.4 L ? should have coil on plug ignition .

Jan 13, 2017 | 2006 Ford F-150 Regular

1 Answer

I have a PO350 code on my Hyundai xg350L. What does it mean and how do I fix it?


P0350 Hyundai - Ignition Coil Primary/Secondary Circuit pdf.gif share.png 2 0 [img alt="P0350 Hyundai Comments" src="http://7ff587e0977842abc470-bfcce390d0a24108a1dce58e5acfca1f.r31.cf1.rackcdn.com/comments.png"> ' Add Comment - Faulty Ignition Coil Primary/Secondary
- Ignition Coil Primary/Secondary harness is open or shorted
- Ignition Coil Primary/Secondary circuit poor electrical connection
- Faulty Engine Control Module (ECM)
[img src="http://7ff587e0977842abc470-bfcce390d0a24108a1dce58e5acfca1f.r31.cf1.rackcdn.com/help.jpg" alt="What does this mean?" > What does this mean?
When is the code detected?
The test fails when the Engine Control Module (ECM) does not receive a valid pulse signal from the ignition coil.
Possible symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Lack/Loss of Power
- Engine may be harder to start
- Engine hesitation
- Rough engine idle
P0350 Hyundai Description
The ignition signal from the Engine Control Module (ECM) is sent to and amplified by the power transistor. The power transistor turns ON and OFF the ignition coil primary circuit. This ON/OFF operation induces the proper high voltage in the coil secondary circuit.


Read more: http://engine-codes.com/p0350_hyundai.html#ixzz3JNf6yMdg

Nov 17, 2014 | Hyundai XG350 Cars & Trucks

1 Answer

How much to replace themasta 2004 kia sedona


If you are talkin about 2004 Kia Truck Sedona 3.5L MFI DOHC 6cyl... then, how to do it? You must do so carefully.

Sep 09, 2010 | 2004 Kia Sedona

1 Answer

2002 kia sedona with a trouble code p0350


po350 is coils 1,2,3,4 failed. The ECU has decided that there is a problem with those relays. They may be bad but check related items first. Could be damaged wiring or could need new spark-plugs. good luck.

Apr 20, 2010 | 2003 Kia Sedona

3 Answers

How many ignition coils hava a kia sedona??????


6 ignition coils, one for each cylinder. 3.5 SFI DOHC.

Apr 09, 2010 | 2002 Kia Sedona

1 Answer

2002 kia sedona with a trouble code p0350


Check Ignition Coil 1. IG KEY : OFF , Engine : OFF 2. Disconnect ignition coil connector B-20/ B-21/ B-22. 3. Measure the primary coil resistance. - Connect the negative (-) terminal of a 3V power supply to terminal 2 of the power transistor; then check whether there is continuity between terminal 3 and terminal 2 when terminal 1 and the positive (+) terminal are connected and disconnected. A. [Specification] 1) In case of connecting terminal 1 with the positive (+) terminal Resistance between terminal 2 and 3: Approx. 0.78Ω±10%(20°C(68°F)) 2) In case of not connecting terminal 1 with the positive (+) terminal Resistance between terminal 2 and 3: infinite(∞Ω) 4. Measure the secondary coil resistance between the high-voltage terminals of the ignition coil. A. [Specification] Approx. 13.0 ± 2.6(kΩ) (20°C(68°F)) sor35d030033.gif sor35d030034.gif 5. Is the ignition coil normal? yes_icon.gif YES 1) Ignition coil is OK. 2) Possibility of PCM malfunction 3) Test with a new PCM and check for proper operation. If problem is corrected replace PCM and go to "Verification Vehicle Repair" procedure. no_icon.gif NO 1) Test with a new ignition coil and check for proper operation.If problem is corrected, replace it. 2) Go to "Verification Vehicle Repair" procedure. findme(''); findme(''); findme('');

Oct 05, 2008 | 2003 Kia Sedona

Not finding what you are looking for?
2004 Kia Sedona Logo

2,288 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75117 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...