Question about 1993 Mitsubishi Eclipse

1 Answer

Possible washer missin

Maybe theres a washer on the back of the axel on the wheel hub side that would make sure taht it wouldn't pull out when u tighten the axel nut

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,486 Answers

There should be a washer behind the nut.

Posted on May 29, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

DIY cv axle 2008 chevy aveo


Jack the vehicle up at proper jack points and lower onto jack stand or stands.remove drivers side wheel. Use needle node pliers and a screwdriver to remove the cotter pin in the axel nut and determine the size of the axel nut. It will most likely be metric 28mm to 36mm. Use an impact to remove the axel nut. Now you will need to remove one or both of the ball joints. Start with the bottom one first and hold the axel in place and pull out on the hub. After you have the hub off of the axel note the splines and how the line up. Now turn the hub so that it is out of the way. You may be able to just yank the axel out of the transmission. If it didn't come out easily you will need a crow bar to gently pry the axel out of the case. Be careful not to put too much pressure on the transmission case. It's aluminum and it will crack and break if you beat on it. Just pry gently and with the transmission in neutral ( be sure to chalk the rear wheels so the car won't run you over) slowly rotate the axel and pry until it comes out. If that doesn't work you will need to rent a slide hammer. Thread it to the free end of the axel and forcefully slide the weight out to knock the axel about of the trans. Installation is reverse. DO NOT USE A HAMMER to force the axel back in you will mushroom the threads and never get the nut on.

Dec 06, 2013 | Chevrolet Cars & Trucks

2 Answers

I have broken lugs on my 2004 Hyundia Santa Fe. I am trying to pull the front left hub off using a puller (3 jaw). The puller is pushing the axel back. I called the local dealer. The Mechanic said I...


You should be able to hammer out the wheel studs
if you have clearance
You shouldn't have to pull the entire bearing assy

Look on YOU TUBE there are all kinds
of videos of hub replacements

You remove the axle nut & 3 or 4 bolts
holding the bearing assy,that is all
The axle stays in place
There is no puller involved

Mar 10, 2011 | Hyundai Santa Fe Cars & Trucks

3 Answers

How to replace a front wheel hub assembly on a 1999 blazer 2wd


remove tire
remove axle nut
remove 3 bolts holding hub in
sometimes may need to hit hub with hammer after all bolts out to get it to release

Dec 22, 2010 | 1999 Chevrolet Blazer

1 Answer

I was going to replace a wheel brake cylinder on my rear axel. I thought I could just pull off the hub to get to the brake assembly but there is a bolted on cap and screwed on plate on the end of the...


Some cars/trucks have the hub mounted with screws/bolts. You will have to remove them to get the hub off. You may need a rubber mallet to beat on the hub a little to get it to come off past the groove the brake pads may have made in the hub. After you get the hub off, take a picture of the brake components so you will know where everything goes once you start removing parts. Once you remove the springs, stuff will shift around and fall out on you so be careful and try to notice where everything goes as it is removed. If you run into problems during reassembly, you can always remove the hub on the other side to get pointers on where everything should go. Good luck.

Oct 11, 2010 | Dodge Ram 2500 Cars & Trucks

1 Answer

Automatic 4x4 locking hubs one side not locking in


There is a possibility the axel U-joint is binding, this will put side load on the hubs and keep them from working properly. Turn the steering wheel either far right or left and with front of truck off the ground or the front end disengaged, see if the axel shafts turn free, both sides. If there is binding the U-joint(s) will have to be replaced.

Dec 17, 2009 | 1996 Ford F150 Regular Cab

1 Answer

How to replace 1996 dodge neon cv joints


Remove the wheel and the lower ball joint from the spindle. It will also make it easier if you remove the tie rod end. There is a large hut at the tire end of the axel. Remove that nut and washer. Take a rubber or brass Hammer and hit the end of the axel to push it through the bearing assembly. If it is really stuck, put the nut back on so that the nut is even with the end of the axel and uses a heavier hamer to break it loose. Once you break it loose, pull back on the rotor while pushing the axel to remove it from the hole it passes through. (Becarefull with the brake hose. If it is pulling too tight it might be best to remove the caliper and use a hanger to suspend it until you are done.) You will need a really BIG screw driver or a pry bar. Put the pry bar between the case and the hub of the axel and push in quickly and firmly to pop it out of the trans axel. It might take a few tries. If it resists look for a ridge and put a big screw drive on the ridge and use a hammer to pop it out.

Once it is out, reverse directions. Do not use the hammer on the new axel any where.put the end into the trans axel as far as it will go and then put the other end through the wheel bearing. Use the leverage you have with the rotor and bearing side to push the axel into the trans. You should hear it snap into place. Before you put the ball joint back on go to the trans axel side and use that pry bar and gently try to remove. if it resists it is seated, if it slides out, you need to seat it again. ONce you are sure it is firmly seated back into the trans, you can bump the ball joint and tie rod back together.

Good luck and be careful
Rich

Aug 18, 2009 | 1996 Dodge Neon

1 Answer

Rear Wheel Bearing Repair; 2005 pontiac aztek


Remove the brake caliper
Remove the disc, (rotor)
Remove the 34mm nut on the axel shaft
Remove the three (3) bolts from the back side
You will need a wheel puller (three jaw will work well)
Place the puller over the hub and tighten, this will push the shaft out of the hub. Now you have to pull the hub assy. out of the mounting bracket. I found hitting each side,of the hub with a lead hammer to work well. Don't forget to disconnect the ABS senser on the back side of the hub assy.
Do not over tighten the 34mm axel nut when you install the new assy. If you use an impact whrench on it you will damage the bearing.

May 01, 2009 | 2005 Pontiac Aztek

1 Answer

Can't figure out how to replace the rear rotor hub.


Your emergency break shoes might be holding you up from geeting the hub off there inside the hub, i think on the back side there should be a slot to get a ajustment tool in there to back them off. If not a big hammer is in order there also might be clips on the wheel studs from the factory. No you don't have to remove the axel. Your the best judge of what needs to be replaced your there, but i would say the ovious rotor, caliper, break pads, and maybe emergency break shoes, maybe backing plate.

Apr 02, 2009 | 2003 Chevrolet Silverado 1500

1 Answer

2006 Saturn Vue Wheel Bearing


it should come out once you have disconnected:Brakes,strut,ball joint.tire rod end,cv joint!if it is not put the cv joint nut back on until safe enough to give it a tap with hammer to knock back & out shaft this should come as one piece HUB the bearing is pressed in! better to change whole HUB good luck this hopefully helped you out!

Jan 31, 2009 | 2006 Saturn Vue

Not finding what you are looking for?
1993 Mitsubishi Eclipse Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...