Question about 1994 Acura Integra

2 Answers

1.8l acura engine cranks over wont start timing check ok

The engine was just rebuilt originally had rod knocking in #4 cyl. got it back from machine shop put it in and put new plugs and wires in it and wont start but cranks over.checked timing on cams and ok there.

Posted by on

  • KEN LaPOINT
    KEN LaPOINT May 11, 2010

    turn the engine over with the distributor cap off and the plugs out.
    as it comes up on compression on the #1 cylinder, is the distributor pointing at the right spot for that plug to fire? or is it 180 degrees off?
    if it's off... pull the distributor out and rotate 180 degrees and drop it back in...
    let me know what you find out.


×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

Did you try the distributor I just had the same problem with my acura and I changed the sensor and it did not work.

Posted on Jun 09, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,486 Answers

Change crank senser

Posted on May 29, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my inline rebuilt 6 cylinder engine knock on my 69 Ford f100?


Putting engine under a load by reving it can get that only if your crank was not perfectly round and checked before install by a machine shop always have them checked along with the engine block. Also it can be one of your connecting rods which is why i go back to the crank being checked out by a professional. Hope that helps!

Apr 15, 2018 | Ford Cars & Trucks

2 Answers

Best way to check the knocking on the lower end of the motor 4.3 GMC do I take lifters off and check down through there


you wont see anything from there --lower knock usually called rod knock caused by a bad bearing or wrist pin [piston pin]to inspect the lower end is by the oil pan you can inspect the crank and rods from there

Jul 31, 2015 | GMC Cars & Trucks

3 Answers

My acura is making loud banging noise from front when idling. sounds like a missing spark plug but all spark plugs are fine. what could it be?


Can be a lot of things.

Could be a bad rod or rod barring.

Could be a clearance issue in a rebuilt engine.

I wouldn't run it until you Take it to a shop for diagnostic.

Nov 03, 2014 | 1998 Acura CL

1 Answer

Engine knocking,1998 safari awd It's the only way to fix bottom end removing the engine or it can be done just taking the oil pan down- Any suggestions thanks Top end was strip and inspected by machin...


sorry to say knocking usually a rod knock--wrist pin-bearings-which means removing engine-also the engine cradle and front end dont let u drop the oil pan to get to the lower end of the crank shaft

Oct 30, 2009 | 1998 GMC Safari

2 Answers

Motor wont crank


It has happened to me that, when ordering parts, i was given .025 oversized bearings after ordering standards. take it back apart, and double check the bearing marks. if they are what you ordered, use some micrometers or plastigage, and get the correct set.

Sep 14, 2009 | 1988 Volvo 240

1 Answer

1994 Honda Accord EX VTEC Engine Knocking.


You will have to pull the engine and remove the crank shaft and connecting rods you have a bad rod bearing. I will strongly suggest taking to a machine shop and having the crankshaft turned and the rods resized. This will be no minor undertaking and will require time to repair. You could also look into purchasing a rebuilt engine.

Apr 30, 2009 | 2001 Chevrolet Metro

3 Answers

Not Sure What Engine to Replace Iron Duke in Fiero


I don't know if you listened to the insane person who previously answered but in a fiero w/o any mods you can bolt in a 3.4 V6 (1992-1995 Camaro/Firebird) or a 4.9 Cadillac V8, four cylinders I'm fuzzy on but I think cavaliers, corsicas etc. engines bolt in, you can do an ecotech but it requires ***loads of work. There is always the Northstar or 350 V8 option ;-] The point is, with a fiero, any engine can go in, just amounts to hours and dollars...

Dec 11, 2008 | 1985 Pontiac Fiero

3 Answers

Crank - Piston Rod Bearing Replacement - Queston


You will have to have the crankshaft machined if the rod bearing is the cause of the noise, so you will have to pull the engine, if u don't do the crank the bearing will fail in a few miles.

Oct 02, 2008 | 1999 Isuzu Rodeo

Not finding what you are looking for?
1994 Acura Integra Logo

Related Topics:

446 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...