Question about 1990 Cadillac Deville

1 Answer

CORRODED PUMP NOSSIL WHICH THE LOWER HOSE GOES INTO MOTOR

MY LOWER HOSE WON'T CONNECT TO THE MOTOR PART BECAUSE IT'S BROKEN AND BENT AND RESULTING IN NO WATER GETTING TO THE MOTOR. DOES THAT PART COMES OFF OR WILL I HAVE TO GET ANOTHER PIECE WELD ON OR GET NEW MOTOR

Posted by on

  • yadayada
    yadayada May 11, 2010

    what are you talking about? lower hose to what from what.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 232 Answers

No,you won't have to replace the motor ,it's a back plate for the water pump and it can be replaced,you can probably have yours repaired ,or a local salvage yard may have one,I'll see if I can locate the new part and comment back with a link for it.

Posted on May 29, 2009

  • George DeMore
    George DeMore May 30, 2009

    The part you need is called the water pump inlet,ufortuanatly I can't find a link to a new one,but it's possible it may be repairable or it should be easy to get one from a local salvage yard.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

........What should the little hose go to from my gas tank filler?......Thanks


It should connect at the filler area, that's a vent tube that lets the gas pump know when to cut off.

Mar 13, 2017 | Cars & Trucks

1 Answer

Where and how do you get to the lower radiator hose on 99 Cadillac sts


Re: Where is the lower radiator hose?(99)
Stand in front of the car, open the hood, and face the engine.

On the left hand side of the radiator, at the top, is the upper radiator hose; which goes to the upper water pump connection.

On the right hand side of the radiator, from the bottom, is the lower radiator hose; which goes to the lower water pump connection.

Where is the lower radiator hose 99
It is a forum and goes on about draining the radiator.

Mar 31, 2015 | Cadillac STS Cars & Trucks

1 Answer

What does Secondary Air Injection Pump - GM (12560095) do on a 2000 gmc jimmy?


its part of the evap system it goes from the pump to the exhaust where the broken end is not far from there it goes.It mixes exhaust into the manifold when needed.

Aug 17, 2014 | Cars & Trucks

1 Answer

I'm getting P1237 first time after replacing new fuel pump. My car; 2000 Ford Taurus DOHC 3.0 L. does not have FPMD, How I fix this code ?


Unplug and check the outside connections and look for bent, broken or corroded pins and reconnect to see if that helps.

Jul 29, 2014 | 2000 Ford Taurus

1 Answer

Will not turn over or even try to turn over. has hot battery and was running fine until parked now will not do anything. also has a different chime alert


Automobiles: 1996 Mercury Sable
Something electrical corroded while it was parked.

connection between battery cable and (lead) battery connector - look for green corrosion of copper wire
cable going from battery to starter motor corroded
corroded ring terminal on starter motor threaded terminal
ignition switch contact corroded at the "start" position
Battery delivers 12 volts, but fails to deliver proper CCA/fails load test
starter motor inoperative
starter solenoid seized/immobile
engine ground wire missing/broken/corroded terminal(s) - frame-to-engine
starter relay failed/corroded terminal(s)
wire from starter relay to starter corroded/missing/corroded terminal(s)

For completeness, here's the Troubleshooting Guide for 1996 Mercury Sable:

Priority Action Part Type Cause
1 Inspect Ignition Switch - Improperly Connected or Faulty Ignition Switch.
2 Inspect Battery - Battery Discharged or Faulty.
3 Inspect Battery Cable - Corroded, Broken, Shorted or Poorly Connected Battery Cable.
4 Inspect Starter Solenoid - Starter Solenoid Faulty.
5 Inspect Starter - Starter Motor Faulty.
6 Inspect Wireset - Worn or Damaged Spark Plug Wires.
7 Inspect Ignition Coil - Faulty Ignition Coil.
8 Inspect Distributor Cap - Loose, Cracked or Worn Distributor Cap.
9 Inspect Spark Plug - Incorrectly Gapped or Fouled Spark Plug(s).
10 Inspect Distributor Rotor - Loose, Cracked or Worn Distributor Rotor.
11 Inspect Fuel Tank - Fuel Tank Empty.
12 Inspect Carburetor - Worn, Faulty or Damaged Carburetor.
13 Inspect Fuel Pump - Faulty Fuel Pump.
14 Inspect Choke - Stuck or Improperly Functioning Choke.
15 Inspect Fuel Filter - Clogged or Dirty Fuel Filter.
16 Inspect Fuel Pump Relay - Faulty Fuel Pump Relay.
17 Inspect Fuel Injector Pressure Regulator - Faulty Fuel Injector Pressure Regulator.
18 Inspect Fuel Pump - Low Fuel Pressure.
19 Inspect Engine Control Computer - Incorrect Operating Information Being Delivered and Sent From The EEC.
20 Inspect Fuel Pump Strainer - Clogged or Dirty Fuel Pump Strainer.

Dec 02, 2011 | 1996 Mercury Sable

1 Answer

Where is the windshield washer motor located? Is it near the heater motor? I had mine fixed and now the heat comes out of the dash for the defroster


Windshield Washer Pump Removal & Installation To Remove:
  1. Remove the air cleaner assembly.
  2. Remove the bolts. windwash.gif

  3. Position the pump and reservoir aside.
  4. Disconnect the electrical connectors.
  5. Disconnect the washer hose.
  6. Remove the pump and reservoir.
  7. Remove the washer pump.
washpump.gif

WARNING
Windshield washer solution contains methanol which is poisonous. Observe all cautions and warnings indicated on label of washer solution container.
NOTE: Windshield washer fluid should be collected in a container after the windshield washer hose is disconnected.
To Install:
WARNING
Windshield washer solution contains methanol which is poisonous. Observe all cautions and warnings indicated on label of washer solution container.
  1. Install washer pump in reservoir.
  2. Install washer pump reservoir assembly.
  3. Connect washer hose.
  4. Connect washer electrical connector.
  5. Install air cleaner assembly.
---
The windshield wiper fluid pump is located in the tank which is not in the heater motor or defroster area in the dash.

The defroster/heat control door is located in the dash board area:

Air Door Actuators, Cables or Motors Removal & Installation Air Inlet Door Vacuum Control Motor To Remove:
  1. Remove the instrument panel lower insulator cover.
  2. Disconnect the vacuum connector.
  3. Remove the control arm clip and the spring.
  4. Remove the nuts and the air inlet door vacuum control motor.
Air inlet door vacuum motor mounting screws for-10-00-245.gif

To Install:
  1. Install the vacuum motor on the mounting bracket.
  2. Connect the control arm and spring.
  3. Connect the vacuum hose to the vacuum motor.
  4. Install the lower instrument panel lower cover.
Floor Defrost Door Vacuum Control Motor To Remove:
  1. Disconnect the negative battery cable.
  2. Remove the left lower dash insulator panel and disconnect the lamp.
  3. Remove the two pin-type retainers and remove the fill panel.
  4. Remove the DLC mounting screws.
  5. Detach the vacuum line.
  6. Remove the lighting module.
  7. Remove the screws and the bracket.
  8. Remove the floor/defrost door vacuum control motor.
Floor/Defrost vacuum motor mounting screws for-10-00-246.gif

To Install:
  1. Connect the vacuum lines and install the floor/defrost vacuum motor.
  2. Install the bracket and lighting control module.
  3. Install the DLC bracket and mounting screws.
  4. Install the fill panel.
  5. Install the left lower dash insulator panel.
  6. Connect the negative battery cable.
Panel Door Vacuum Control Motor To Remove:
  1. Remove the instrument panel.
  2. Reach through the door opening and remove the pin.
  3. Disconnect the panel door vacuum control motor vacuum line.
  4. Remove the screws and remove the panel door vacuum control motor.
To Install:
  1. Install the panel door vacuum motor.
  2. Connect the vacuum line to the panel door motor.
  3. Reach through the opening and install the pin to the linkage.
  4. Install the instrument panel.
prev.gif next.gif

Jan 19, 2011 | 2003 Mercury Grand Marquis

1 Answer

I am refitting new injectors to my 2.8 diesel 4m40 engine. what is tehe torque setting for these please


55nm for injection nossil and 40nm for injection nossil to body and 5nm for injection clamp nut , these spec's i downloaded from delica club for 4m40 motor

hope this helps , there are many do it youself manuals available from this site including fuel pump diagarams and injection instalation and removal . good luck

Sep 14, 2009 | Mitsubishi Minivan Cars & Trucks

1 Answer

Wat keeps a car cutting off for a dodge stratus 2002 coupe r/t


1 Inspect Catalytic Converter Clogged or Faulty Catalytic Converter. 2 Inspect Piston Ring Set Worn or Broken Piston Rings. 3 Inspect Distributor Worn, Damaged or Faulty Distributor 1 Inspect FreshAir Intake Hose Clogged or Damaged FreshAir Intake Hose.
1 Inspect Battery Battery Discharged or Faulty. 2 Inspect Battery Cable Corroded, Broken, Shorted or Poorly Connected Battery Cable. 3 Inspect Solenoid Switch Faulty Solenoid Switch. 4 Inspect Starter Starter Motor Faulty. 5 Inspect Ignition Switch Improperly Connected or Faulty Ignition Switch. 6 Inspect Distributor Cap Broken or Corroded Distributor Cap. 7 Inspect Spark Plug Fouled, Damaged, or Broken Spark Plug(s). 8 Inspect Fuel Pump Faulty Fuel Pump. 9 Inspect Fuel Injector Fuel Injectors Dirty or Burned. 10 Inspect Distributor Cap and Rotor Kit Broken or Corroded Distributor Cap. 11 Inspect Fuel Tank Fuel Tank Empty. 12 Inspect Carburetor Worn, Faulty or Damaged Carburetor.

Sep 02, 2009 | 2002 Dodge Stratus

1 Answer

Windshield wiper fluid not coming out


get someone else to feel if the eletiric pump on the bottom of the fluid bottle is working.
other faults see if the lines going from the bottle to the nossils are not cut or split check the nossils are not blocked use a pin of some type.

Feb 16, 2009 | 2004 Chrysler Sebring

1 Answer

Radiator Hoses......????????????


that little hose is called a by-pass hose the upper should go to the intake manifold where the thermostat is you have a lower hose tah goes to the water pump and then you have a very small hose tah connects at the neck of the radiator that goes to your overflow tank. the hose should be about 15 bucks.. please rate this thanks

Sep 24, 2008 | 1993 Toyota Celica

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...