Question about 2003 Cadillac CTS

1 Answer

Accessing right front turn light for bulb replacement

How do you access the right front turn light for bulb replacement

Posted by on

  • esnj Jun 02, 2009

    Thanks very much for a quick and concise reply!!!

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I just had to do this. You have to jack up the car, take off the right front tire, go in the right front wheel well and pull out a handful of tricky plastic nails then, pull back the flaps. All the lights are right there. It is pretty easy, just a pain in the neck. Hope this helps

Posted on Jun 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My right front turn signal on my 2001 ford ranger doesnt work and my inside right turn signal light on dash doesnt work and flashes really fast. Buld on right side was replaced and works when lights


was the correct bulb used? this sounds like a single function bulb was used NOT the bulb that will light with the headlights and ALso produce turn singles

Dec 06, 2014 | 2001 Ford Ranger Regular Cab

1 Answer

How to replace rear turn signal bulb 99 park avenue


Replacing a front turn signal bulb is easy, as I just did my own. On the front driver's side, look at the wheel well splash panel and you'll see one plastic pin. Use a claw hammer and pull the pin out. Now just pull the plastic splash panel out of your way.

Look behind the front bumper and you'll see the light fixture. The top left wire and & bulb socket is right there. Give the socket a 1/4 turn to the left and you have access to replacing the bulb which is a 194, available at any parts store, 2 for $5.00.

Jul 07, 2012 | 1999 Buick Park Avenue

1 Answer

Need instructions on how to change a parking light bulb an a 2008 Pontiac van montana.


First ascertain from the auto parts dealership with vehicles brands about the availablitity of parking lights bulbs. Once acquired, the installation process takes over as explained. Second, decide on contacting a electrician at the mechanics else the processes performing the task elsewhere requires the appropiate tools, time, and an extra pair of hands. Third, depending on the type of vehicle, the parking lighting bulbs would be accessible by reaching into the engine if the replaceable ones are at the front, or accessing the truck area from the interior of the vehicle if the rear bulbs require repairs. However also,the type of vehicle may least require loosing of screws or bolts and nuts. A more complicated vehicle may require tools capable of reaching into the engine, and sometimes require applying pressure to extract the blown fuse bulbs. Contact an electrical expert at the mechanic.

Jan 18, 2011 | Pontiac Montana SV6 Cars & Trucks

2 Answers

Replacing brake light on a subaru outback limited wagon 2000


How To Install Replace Change Taillight and Bulb 2000-04 Subaru Outback

Apr 07, 2010 | 2000 Subaru Outback

2 Answers

How do I access the front left indicator light for


2fac621.gif
To change a front parking/turn signal lamp bulb on Town & Country models, remove the screw, and hinge the lamp on the tab


b2dedfc.gif
With the lamp free of the facia, the bulbs can be accessed by twisting the sockets counterclockwise, and pulling the bulb from the socket

1.Pull the bulb straight out of the socket.
2.Replace the bulb.
3.Installation is the reverse of the removal procedure.
4.Verify light operation.

Jan 19, 2010 | 1996 Dodge Caravan

1 Answer

Replace rt. front turn signal bulb


look at the other side,under the bumper you just twist and turn and you will have access to change your bulb.

Aug 09, 2009 | 1999 Chevrolet Cavalier

1 Answer

Accessing left lowbeam light to replace connectors


Most head light bulbs are easily accessible from the rear, inside the engine compartment. Sometimes it is easier to move the battery for better access. Remember not to touch the bulb as it will greatly reduce it's life.

May 09, 2009 | Saturn Outlook Cars & Trucks

4 Answers

Front signal light not working and rear signal lights flashing fast on 1999 intrigue


Your front turn signal socket is shot. Buy a new one at the dealer for about 30.00. It will fix it. You may be able to clean it and wiggle it to get it to work. But it wont last very long. I had the same problem. Replaced the socket and it is fine. Note: If one side is bad the other side it not far behind. Probably 2 or 3 months it will go also. Good Luck.
Bill

Apr 17, 2009 | 1999 Oldsmobile Intrigue

1 Answer

Front right turn signal bulb is burnt out


If you open your hood and look right behind the headlamp assembly you will see a gray release tang for the turn signal housing. Just press the tang and pull out the housing. The socket comes out of the housing with a 1/4 turn counter clockwise. Now replace the bulb. The 2 problems are not related so check your fuses and replace any that are blown. It's a good idea to test the fuses with the key on and all lights turned on with a 12 volt test light and not by eyeballing them.

Jan 01, 2009 | 1994 Mercedes-Benz E-Class

2 Answers

Replace front driver signal light bulb


Depending on whether it is the front or the back turn indicator light will determine on what needs to be done. If it is the front turn indicator light open the hood of the car you may need to take the entire headlight out. The headlight may have screws, take the screws out then the front light will come out from the outside of the vehicle replace the burned out bulb. The bulb should snap right in and then put the headlight back in make sure you put all screws back in from the inside of the hood. Step2 If it is the back turn indicator light, go through the trunk of the vehicle. If there is a panel covering the lights you must unscrew the panel and then replace the burned out light bulb. Some panels can be folded down without removing all of the screws to access the lights. This light may not require for you to pop the entire light out you maybe able to just replace the bulb. After you have replaced it screw the panel back into place. The back light should not require the entire light to be lifted out just a simple bulb replacement. Step3 In replacing either the front or the back indicator light you must gain access to the turn signal housing which is usually in the same case as the headlight or your rear lights. It is very helpful to also get the owners manual out this will tell you exactly what type of bulbs you will need to get to replace the indicator bulb.

May 29, 2008 | 2005 Cadillac SRX

Not finding what you are looking for?
2003 Cadillac CTS Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...