Question about 2002 Jaguar S-Type

1 Answer

TOP END NOISE AFTER I CROSSED HOSES

The 2 rear cylinders filled up with coolant. I removed spark plugs and cleaned the cylinders out, then I tried starting the engine and heard what sounded to me like a LIFTER noise or VALVE type sound. My ? is....... what is the procedure to remove & inspect the lifters or, if necessary, remove the cylinder head?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jaguar Master
  • 1,869 Answers

If your cylinders filled up with coolant ...you have a blown head gasket or, cracked engine head

Posted on May 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change the radiator fluid?


Most radiators have a drain plug on the bottom tank the engine block also has a drain plug . Remove the radiator cap ,open both drains ,let all the coolant run out, if there is no radiator plug remove the lower hose , remove the heater demister hoses, with the heater control on hot flush out all the coolant from the heater radiator. with a garden hose, till the water runs clean, tighten the radiator plug or re fit the hose,put a garden hose into the radiator and flush out till the water at the block plug runs clean ,refit the heater hoses, refit the block plug, fill the radiator from the hose leave the cap off , If it has a overflow tank clean and flush it. start and run engine for 5 minutes top up radiator if needed . stop engine and drain out all water. most important that all old coolant is drained out, only buy the best coolant you can . If you make up your own use only distilled water. keep some to top up with never mix with another brand. Fill radiator with coolant top up over flow tank, run engine top up coolant as needed, refit radiator cap run for another 10 minutes check for leaks,

Oct 14, 2014 | 2006 Chevrolet Trailblazer

1 Answer

How to bleed the radiator on a peugeot 2006 307 XS model


B1GG0RK1 - 206 TU ENGINE DW8 ENGINE
DRAINING - FILLING - BLEEDING COOLING SYSTEM
1 - SPECIAL TOOLS
b1gk06lc.gif[1] filling cylinder (-).0173/2 .
2 - DRAINING
TU ENGINE
b1gk070c.gifDW8 ENGINE
b1gk073c.gifALL MODELS
Carefully remove the expansion chamber cap .
b1gk06kc.gifUnscrew the radiator drain plug (1) .
NOTE : fit a pipe to the outlet to allow clean drainage of the system .
TU ENGINE
b1gk071c.gifDW8 ENGINE
b1gk074c.gifALL MODELS
Open the bleed screws (2) .
DW8 ENGINE
b1gk075c.gifDrain the engine by removing the plug (3) .
ALL MODELS
3 - FILLING AND BLEEDING THE SYSTEM
Before any re-filling operation, flush the cooling circuit with clean water .
WARNING : check the cooling system for leaks .
DW8 ENGINE
b1gk076c.gifTU ENGINE
b1gk072c.gifALL MODELS
Fit the filling cylinder [1] to the filler opening .
Open all the bleed screws .
Fill the circuit slowly with coolant .
Close the bleed screws in the order in which the liquid flows without bubbles .
The filling cylinder must be filled to the 1 litre mark to bleed the heater matrix correctly .
Start the engine .
Maintain the engine speed at 1500 to 2000 rpm until the end of the second cooling cycle (fan(s) starting then stopping) keeping the filling cylinder filled to the 1 litre mark .
Stop the engine .
Remove the filling cylinder [1] .
Immediately tighten the plug on the expansion chamber .
If necessary fill up to the level of the maximum mark (Engine cold) .

Jul 06, 2014 | Cars & Trucks

2 Answers

Timming chains....... engines not starting, just rotates and blows water out of the radiator when caps off. points and sparks lokks good, I sucpect, it might be the T/chains


Hello robtui: My name is Roger and I will help with your problem. The engine cranks over and does not start? Collant is belched out of the radiator? Problem is a warped head(s).Blown head gasket or cracked head. Remove the spark plugs fill the coolant system and you should see coolant fill and run out a spark plug hole. The engine should of had a miss before this happend. You could also do a compression test instead of filling the radiator and looking for coolant to run out. Either way you will find a cylinder compression leaking to the coolant passage. Should you need further help please just ask. Please rate the answer. Thank You for using Fix Ya. Roger

Jun 21, 2011 | 1994 Buick LeSabre

1 Answer

Trying to replace thermostat on a gonda accord LV v6. remove two hoses. assumes the thermostat was in one of them. I was wrong. Do I need to remove both hoses to replace the thermostat. And I keep reading...


Drain about 1 gallon of coolant from radiator Follow upper radiator hose to engine should end at housing secured to engine by 2 or 3 bolts Remove housing make note how thermostat is installed in housing Clean both surfaces completely Install new gasket and thermostat secure housing evenly to engine re-fill radiator Start engine and check for leaks Bring engine up to normal operating temperature with heater on Re-check coolant level

May 26, 2011 | 1998 Honda Accord

2 Answers

Car has been sitting in garage for past 10 years, on blocks. what do you recommend before trying to start? it needs new battery.


you need drain fuel tank.fuel tank probably need to be removed and cleaned out to remove all sediment in bottom of fuel tank.remove each sparks and label them.squirt some clean engine oil down the spark holes into cylinder bores to help lubricate cylinder walls and help seal the piston rings to build up compression.replace fuel filter.best to change spark plugs and wires.check all brake hoses they more likely old cracked. i would change brake fluid bleed out all the old brake fluid out of the brake system.also change power steering fluid and change transmission fluid and filter also change engine oil and oil filter.replace the antifreeze and all the coolant hoses and radiator hose.replace thermostat and radiator pressure cap.replace battery and add new full tank of gas.you should be ready go. check ignition timing also.

Apr 26, 2011 | 1991 Honda Accord

1 Answer

To remove 1993 mustang conv. top cylinders should top be up or down? thanks, bill


don't have 93. here's 94

Motor Assembly, Convertible Top Removal and Installation
NOTE: The folding top hydraulic cylinder rods should be in the fully retracted position.
Use absorbent rags or a container to catch any hydraulic fluid that leaks out when removing the fittings.
  1. Remove motor and pump assembly as outlined.
  1. Loosen each folding top motor upper and lower hose fitting on the sides of the folding top hydraulic lift motor and plate kit (533A00) .
  1. Remove the folding top hydraulic lift motor and plate kit .
  1. Remove each of the service folding top hydraulic lift motor and plate kit plugs one at a time and attach the tee fitting to the replacement folding top hydraulic lift motor and plate kit . NOTE: Make sure that the o-ring is installed in the bottom of each folding top hydraulic lift motor and plate kit port before attaching the hose tee fitting.
  1. Connect the folding top hydraulic lift motor and plate kit unit to a 12-volt power source and cycle the folding top hydraulic lift motor and plate kit in and out several times to purge the air from the folding top motor upper and lower hoses (53390) . Some noise squeal may be noticed due to the air. srb~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not overfill or the reservoir seal could be blown out.
  1. Carefully remove the rubber fill plug from the back and the reservoir and check the fluid level. The level should be at the bottom of the filler hole. If necessary, add Synthetic Mercon® Multi-Purpose Automatic transmission fluid E6AZ-19582-B (ESR-M2C163-A2) or equivalent.
  1. Replace the fill plug with a new fill plug.
  1. To install, reverse Removal procedure.
-------------------------------------------------------------------------------------------------------------------------------
Section 01-17: Convertible 1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION Lift Cylinder, Power Top Removal and Installation
NOTE: The cylinder rods should be in the fully-retracted position.
  1. Remove pump and motor as outlined.
  1. Remove the upper and lower hose fitting from the folding top hydraulic cylinder (50600) . Use absorbent rags or a container to catch any hydraulic fluid that leaks out when removing the fittings.
  1. Remove each of the service cylinder plugs one at a time and attach the hose fittings. NOTE: Be sure each fitting is installed in the correct position on the folding top hydraulic cylinder .
    NOTE: Make sure that the tetra seal is installed in the bottom of each of the folding top hydraulic cylinder ports before attaching the upper and lower hose fittings.
  1. Connect the folding top hydraulic lift motor and plate kit (533A00) to a 12-volt power source and cycle the folding top hydraulic lift motor and plate kit in and out several times to purge the air from the hoses. Some noise squeal may be noticed due to the air.
  1. Carefully remove the rubber fill plug from the back and the reservoir and check the fluid level. The level should be at the bottom of the filler hole. If necessary, add Synthetic Mercon® Multi-Purpose Automatic transmission fluid E6AZ-19582-B (ESR-M2C163-A2) or equivalent.
  1. Replace the fill plug with a new fill plug.
  1. To install, reverse Removal procedure.

Jan 21, 2011 | Ford Mustang Cars & Trucks

1 Answer

NEED HELP WITH TORQUE SPECS ON 1998 CHEVROLET SURBURBAN CYLINDER HEADS 5.7


Cylinder Head Removal & Installation 5.7L Engine To Remove:
  1. Disconnect the negative battery cable.
  2. Drain the engine coolant.
  3. Remove the air cleaner assembly.
  4. Remove the upper radiator hose.
  5. Remove both heater hoses.
  6. Disconnect spark plug wires at distributor cap.
  7. Remove distributor cap.
  8. Remove the coolant bypass hose from the water pump.
  9. Remove the drive belt. NOTE: It is not necessary to evacuate the A/C refrigerant.
  10. Remove the A/C compressor from the mounting bracket and set it aside.
  11. Remove the wiring bracket from the rear of the cylinder head.
  12. Disconnect the accessory bracket and slide forward.
  13. Remove the upper and lower intake manifold.
  14. Remove the exhaust manifolds.
  15. Remove the valve rocker arms and pushrods.
  16. Remove the power steering pump pulley.
  17. Disconnect the electrical connector from the power steering pump.
  18. Remove nuts attaching the power steering pump to the engine.
  19. Remove power steering pump mounting bracket bolts and nut.
  20. Slide power steering pump/bracket assembly forward and remove stud.
  21. Set power steering pump/bracket assembly aside.
  22. Disconnect the wiring bracket from rear of the right cylinder head.
  23. Remove the generator.
  24. Remove the oil indicator tube bracket bolt.
  25. Remove the generator mounting bracket.
  26. Remove the sixteen cylinder head bolts.
  27. Remove cylinder heads and gaskets.
  28. Clean all sealing surfaces.
To Install:
Right Side NOTE: Clean all dirt, debris, and coolant from the engine block cylinder head bolt holes. Failure to remove all foreign material may result in damaged threads, improperly tightened fasteners or damage to components.
NOTE: Do not use any type of sealant on the cylinder head gasket (unless specified).
  1. Clean the cylinder head bolt holes with a thread chaser and compressed air.
  2. Check the cylinder head locating pins for proper installation.
  3. Place a new cylinder head gasket over the engine block dowel pins.
  4. Install the cylinder head to the engine block.
  5. Apply sealant (GM P/N 12346004 or equivalent) to cylinder head bolt threads.
  6. Install the cylinder head bolts. gm-03-50-685.gif

  7. Tighten the cylinder head bolts in sequence on the first pass.
    • Torque to: 22 ft. lbs. (30 Nm)
  8. Using a torque angle meter, tighten the long bolts (1, 2, 5, 6, 9, 10 and 13) on the second pass in sequence to 75°.
  9. Using a torque angle meter, tighten the medium bolts (14 and 17) on the second pass in sequence to 65°.
  10. Using a torque angle meter, tighten the short bolts (3, 4, 7, 8, 11, 12, 15 and 16) on the second pass in sequence to 55°.
  11. Install the valve rocker arms and pushrods.
  12. Install the generator mounting bracket stud.
    • Torque to: 15 ft. lbs. (20 Nm)
  13. Loosely assemble the generator mounting bracket over the stud.
  14. Install all nuts and bolts finger tight.
    • Torque to: 30 ft. lbs. (41 Nm)
  15. Install the generator.
  16. Install the oil indicator tube bracket bolt.
  17. Install the exhaust manifold.
  18. Install the lower intake manifold.
  19. Install the valve rocker arm covers.
  20. Install the wiring bracket to the rear of the cylinder head.
  21. Connect the accessory bracket.
  22. Install the A/C compressor.
  23. Install the drive belt.
  24. Install the distributor cap.
  25. Connect the spark plug wires to the distributor cap.
  26. Install both heater hoses.
  27. Install the upper radiator hose.
  28. Install the air cleaner assembly.
  29. Refill the engine coolant.
  30. Connect the negative battery cable.
Left Side To Install:
NOTE: Clean all dirt, debris, and coolant from the engine block cylinder head bolt holes. Failure to remove all foreign material may result in damaged threads, improperly tightened fasteners or damage to components.
NOTE: Do not use any type of sealant on the cylinder head gasket (unless specified).
NOTE: Clean all dirt, debris, and coolant from the engine block cylinder head bolt holes. Failure to remove all foreign material may result in damaged threads, improperly tightened fasteners or damage to components.
NOTE: Do not use any type of sealant on the cylinder head gasket (unless specified).
  1. Clean the cylinder head bolt holes with a thread chaser and compressed air.
  2. Check the cylinder head locating pins for proper installation.
  3. Place a new cylinder head gasket over the engine block dowel pins.
  4. Install the cylinder head to the engine block.
  5. Apply sealant (GM P/N 12346004 or equivalent) to cylinder head bolt threads.
  6. Install the cylinder head bolts. gm-03-50-685.gif

  7. Tighten the cylinder head bolts in sequence on the first pass.
    • Torque to: 22 ft. lbs. (30 Nm)
  8. Using a torque angle meter, tighten the long bolts (1, 2, 5, 6, 9, 10 and 13) on the second pass in sequence to 75°.
  9. Using a torque angle meter, tighten the medium bolts (14 and 17) on the second pass in sequence to 65°.
  10. Using a torque angle meter, tighten the short bolts (3, 4, 7, 8, 11, 12, 15 and 16) on the second pass in sequence to 55°.
  11. Install the valve rocker arms and pushrods.
  12. Install the power steering pump mounting bracket stud.
    • Torque to: 15 ft. lbs. (20 Nm)
  13. Loosely assemble the mounting bracket over the stud.
  14. Install all nuts and bolts finger tight.
    • Torque to: 30 ft. lbs. (41 Nm)
  15. Install the power steering pump pulley.
  16. Connect the electrical connector to the power steering pump.
  17. Install the exhaust manifold.
  18. Install the lower intake manifold.
  19. Install the valve rocker arm covers.
  20. Install the wiring bracket to the rear of the cylinder head.
  21. Connect the accessory bracket.
  22. Install the A/C compressor.
  23. Install the drive belt.
  24. Install the distributor cap.
  25. Connect the spark plug wires to the distributor cap.
  26. Install both heater hoses.
  27. Install the upper radiator hose.
  28. Install the air cleaner assembly.
  29. Refill the engine coolant.
  30. Connect the negative battery cable.

Aug 31, 2010 | Chevrolet Suburban 1500 Cars & Trucks

1 Answer

Whats the tourqe on head bolts 1990 4 cylinder


1990–95 VEHICLES
  1. Disconnect the battery ground.
  2. Drain the cooling system. CAUTION
    When draining the coolant, keep in mind that cats and dogs are attracted by ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.
  3. Disconnect the hoses at the thermostat housing.
  4. Remove the air cleaner.
  5. Remove the rocker arm cover as outlined earlier in this section.
  6. Remove the rocker arms. Keep them in order!
  7. Remove the pushrods. Keep them in order!
  8. Remove the power steering pump bracket.
  9. Suspend the pump out of the way.
  10. Remove the intake and exhaust manifolds.
  11. Remove the air conditioning compressor drive belt.
  12. Loosen the alternator drive belt.
  13. Remove the compressor/alternator bracket mounting bolt.
  14. Unbolt the compressor and suspend it out of the way. DO NOT DISCONNECT THE REFRIGERANT LINES!
  15. Remove the spark plugs.
  16. Disconnect the temperature sending unit wire. Fig. 6: Disconnect the coolant hoses at the thermostat housing 85353100.jpg
    Fig. 7: Disconnect the coolant hoses at the thermostat housing 85353101.jpg
    Fig. 8: Remove the cylinder head–to–block bolts 85353102.jpg
    Fig. 9: Cylinder head bolt removed from the head 85353103.jpg
    Fig. 10: Removing the cylinder head from the engine block 85353104.jpg

  17. Remove the head bolts.
  18. Lift the head off the engine and place it on a clean workbench.
  19. Remove the head gasket. To install:
  20. Thoroughly clean the gasket mating surfaces. Remove all traces of old gasket material. Remove all carbon deposits from the combustion chambers. Lay a straightedge across the head and check for flatness. Total deviation should not exceed 0.001 in. (0.025mm). NOTE: The cylinder head gasket used on the 2.5L engine is a composition gasket. The gasket is to be installed dry. Do not use gasket sealing compound on the gasket.
  21. Fabricate 2 cylinder head alignment dowels from 2 used cylinder head bolts. Cut the head of the longest bolt off below the hex head. Then cut a slot in the top of the dowel to allow easier removal with a screwdriver.
  22. Install one dowel in bolt hole No. 10 and the other dowel in bolt hole No. 8.
  23. Place the cylinder head gasket over the dowels with the numbers facing up.
  24. Place the cylinder head over the dowels.
  25. Coat the threads of bolt No. 7 only, with Loctite PST sealant or equivalent.
  26. Install all head bolts except Nos. 8 and 10.
  27. Tighten the bolts in the sequence shown in the illustration to the following:
    1. Tighten bolts 1 through 10 in sequence to 22 ft. lbs. (30 Nm).
    2. Tighten bolts 1 through 10 in sequence to 45 ft. lbs. (61 Nm).
    3. Recheck bolts 1 through 10 in sequence to verify that they are 45 ft. lbs. (61 Nm).
    4. Tighten bolts 1 through 6 in sequence to 110 ft. lbs. (149 Nm).
    5. Tighten bolt 7 to 100 ft. lbs. (136 Nm).
    6. Tighten bolts 8 through 10 to 110 ft. lbs. (149 Nm). NOTE: During the final tightening sequence, bolt No. 7 will be tightened to a lower torque than the rest of the bolts. Do not overtighten bolt No. 7.
  28. Connect the temperature sending unit wire.
  29. Install the spark plugs.
  30. Install the compressor.
  31. Install the compressor/alternator bracket mounting bolt.
  32. Adjust the alternator drive belt.
  33. Install the air conditioning compressor drive belt.
  34. Install the intake and exhaust manifolds.
  35. Install the power steering pump bracket.
  36. Install the pushrods. Keep them in order!
  37. Install the rocker arms. Keep them in order!
  38. Thoroughly clean the mating surfaces of the head and rocker cover and install as outlined earlier in this section.
  39. Install the air cleaner.
  40. Connect the hoses at the thermostat housing.
  41. Connect the battery ground.
  42. Fill the cooling system.

Jul 08, 2010 | 1990 Jeep Wrangler

3 Answers

Where is the drain plug for the radiator


Should be a drain **** at the bottom of the radiator that unscrews out. It looks like a wing nut has been welded to a bolt on the end of it. Another way to do this is just pull off the bottom hose.

Mar 31, 2010 | 2001 Jeep Cherokee

1 Answer

Chevy k1500 5.7 v8 wont start


Sounds like your timing is off when you placed the distributor back in or your spark plug wires are crossed. Start with the simple and check the spark plug wire firing order. 1-8-4-3-6-5-7-2 Cylinder numbers drivers side 1-3-5-7 radiator to firewall. Cylinder numbers passenger side 2-4-6-8 radiator to firewall. Distributor cap #1 is at 5 O'clock and rotates clock wise. Once that is establish to be good then make sure the cylinder 1 is at TDC with the distributor rotor at the #1 position. Good luck and hope it's a crossed firing order.

Jan 11, 2010 | 1994 Chevrolet K1500

Not finding what you are looking for?
2002 Jaguar S-Type Logo

Related Topics:

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

74945 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...