Question about 1997 Acura TL Series

1 Answer

Abs light on

I changer abs new but they still light on

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 129 Answers

Did you have the code cleared by a scanner? If not have a mechanic scan for any codes in the ABS system, it is possible a sensor may have to be replaced as well.

Posted on May 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How too take abs light off after new brakes are fitted


Fitting new brakes wouldn't usually put the abs light on unless you disconnected the abs and then switched on the ignition, made an unfortunate mistake or coincidentally an abs fault occured naturally.

The abs light is supposed to illuminate for a few seconds when the ignition is switched on and then go out signalling there are no faults. If the abs light is on it means a fault has been detected.

Early systems would cancel the light when the fault had been located and rectified but I believe modern systems require the use of diagnostic equipment.

Jun 12, 2016 | Cars & Trucks

1 Answer

Just had new disc an brake pads and new abs sensors an my abs light is still on


Might want to take it to a car dealership and get that checked out. Either something's still not quite right with your brakes, or your light simply needs resetting. Try consulting the owner's manual.

Feb 17, 2013 | 2000 Renault Laguna Estate

1 Answer

Abs light still dose go off after fitting to new abs sensors?


new abs and speed sensor fitted light still on do codes have to be cleared

Nov 27, 2011 | Cars & Trucks

1 Answer

Chevy Blazer 2001


Find a qualified shop to scan the ABS system and find out why the light is on. Having a good shop is the only way to avoid "parts changers" which will cost you way more than repairs.

Sep 22, 2009 | 1997 Chevrolet Blazer

1 Answer

ABS Light Stays on new brakes put on


Could be dirty abs sensors attached to your brakes. I would clean them with brake parts or elecronical cleaner.
Other possibility is a faulty ABS system.

May 22, 2009 | 2003 Volkswagen New Beetle Convertible

1 Answer

2005 impala


All the hubs on the car have the abs sensor built into the hub. The abs system has to be re set to read the sensor . The rear hub bearing if noisy should be replaced. There are wiring harnesses that connect to the abs sensor. The harnesses to each of the abs sensor should be replaced.

Mar 18, 2009 | 2005 Chevrolet Impala

1 Answer

ABS Light is on


When the ABS light comes on and stays on there is an issue with the Anti-lock Brake System. As long as the light is on you do not have ABS and to turn the light off you need to have the system repaired.

Jan 26, 2009 | 1999 Volkswagen New Jetta

1 Answer

Seat belt, ABS and radio issues


chances are the seatbelt is jammed and has to be replaced either with a new factory part or a used one. 2nd you probably heated the sending unit for the abs on the wheel and as a result it has thrown the code. 3rd if you have a cd changer it will either be located in the trunk or it will be loocated in the dash console. Note: if you have the abs sending unit replaced you still will need to clear the code so the light goes out.

Aug 30, 2008 | 1998 Mercury Sable

Not finding what you are looking for?
1997 Acura TL Series Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...