Question about 1999 Plymouth Grand Voyager

1 Answer

Replacing Blower fan info

Is there a "How To" repair diagram for replacing the blower fan on a 99 Plymouth Voyager, v6 3.0 Mine is sluggish to rotating very slowly. Sometimes wacking it with the palm of my hand under the glove compartment housing vibrates it enough to start it rotating! Thanks

Posted by on

  • w_ankenbauer Jun 01, 2009

    Thanks polarcycle, it sounded easy and it was.
    I first removed the glove compartment, tool the cover off the blower housing to reveal the blower motor, and like you said there was only three screws holding it in. The fan dropped down, I unplugged it, and installed a new motor in reverse. Works like a charm!
    Thanks again


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,392 Answers

Should be only 3 screws holding it in Unplug, remove the screws and remove the blower motor.

Posted on May 30, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to replace blower fan resister for 99 Plymouth voyager?

ok the resister is near the fan in the ductwork inside cab normally behind glove box remove it. its normally held in with 2 screws and has wires plugged into it

Aug 20, 2014 | Cars & Trucks

2 Answers

The heater fan is not working. Is it a fuse?

fuses are the easy thing to check just pull one and look at it if you see a burned spot replace it, checking relays and blower motor resesters and blower motors are harder if you dont know how to do it. there best left to a shop to check.

Dec 16, 2010 | 1999 Plymouth Voyager

1 Answer

My 2001 Voyager blower fan only runs on high.

This is 100% the Blower (Fan) Motor Resistor located near the Blower Motor.
This is a very common problem with Chyrsler, Dodge, Plymouth. The key symptom is the Fan only working on High.
This is very easy to access and replace.

Let me know if this helped....

May 11, 2010 | 1999 Chrysler Sebring

2 Answers

Heater fan will not run some of the time, if you go in through the glove box and give it a good whack it will start most times, not wanting to start now.

replace the blowermotor thats your problem, another thing is the resistor for the blowermotor, replace that while your there replacing the motor.hope this helps, heres some diagrams to help also.the resistor is under the hood next to pass/side strut tower heres a diagram, the blower is behind glove box area.892e04b.gif80f8288.jpg

Feb 06, 2010 | 1996 Plymouth Grand Voyager

1 Answer

'99 Plymouth Grand Voyager fan switch issues

The problem is not with the switch, it's the blower motor resistor. The resistor is usually located in duct work near the blower motor. It will have 4or 5 wires going to it and is held in place with a couple screws. These things generate heat, so they put them in duct work so the fan blows air across them to keep them cool. Sometimes the plug gets hot and melts, you should be able to buy the resitor and the plug with wires (pig tail) from an auto parts store or a dealer. The resistors are usually about $50 the pig tail is about $30.

Dec 02, 2009 | 1999 Plymouth Grand Voyager

1 Answer

The fan blower only works on high. The other

its the resistor, and its located with the blower motor. you will need a new motor assy. Chryslers infinite wisdom, its all one unit.

Oct 08, 2009 | 1998 Plymouth Voyager

1 Answer

1st 2nd and 3rd fan speeds dont work when a/c or just fan is on... this is on a 99 plymouth breeze.. what do i do?

You need a blower motor resistor. The resistor is fairly inexspensive and is fairly easy to get to and replace. Hope this helps. Good luck.

Jun 29, 2009 | 1999 Plymouth Voyager

1 Answer

Location needed for blower senser on 99 plymouth voyager

the blower resistor is under the hood at the firewall on pass side... there are no screws just tabs holding it in place... the pigtail is usually needed when the resistor goes bad it melts the harness

Feb 12, 2009 | 1999 Plymouth Grand Voyager

1 Answer

Blower motor

It's in behind glove box, you will probably have to remove glove box, but a good look up from under will tell you. You did check fuses & resistor right? Did it run for a while on high only?

Jan 08, 2009 | 1999 Plymouth Grand Voyager

1 Answer

Blower fan

Blower fan resistors are in the air box on the passenger side below the dash. Basically right at the passengers feet.

Jan 02, 2009 | 1996 Plymouth Voyager

Not finding what you are looking for?
1999 Plymouth Grand Voyager Logo

396 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts


Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides