Question about Dodge Durango

1 Answer

Knock sensor dont work for 2005 dodge durango

I got a check engine reading and it happens to be my knock sensor. i need to know where its located and the best way of fixing it.

Posted by on

  • Anonymous Mar 26, 2014

    No knocks and get 25 miles per gallon

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Dodge Master
  • 74,945 Answers

This problem is very seldom the knock sensor, it can be the harness connector at the sensor or the engine has excessive knock which will set a code, u did not mention the particular code so hard to say, the location of the knock sensor is the lower section of the engine block, it is screwed into what would normally be a block drain plug, if u replace it u need to torque it to whatever the factory spec is or it can cause it throw another code..

Posted on May 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Knock sensor location on a 2005 dodge Durango 4.7 liter


There are two knock sensors, and they are installed into the block (left and right side) under the intake manifold. The intake manifold must be removed to replace them. They are not identical, and must be installed in the correct position (they are tagged) so that the PCM knows which is which.

Jan 09, 2016 | Dodge Cars & Trucks

1 Answer

4.7l Magnum engine. Where is knock sensor located?


left rear of engine, link below
press the helpful button

Jan 09, 2016 | 2005 Dodge Durango

1 Answer

Where is the o2 sensor bank sensor 2 located on a 2005 dodge durango 4.7 engine I get an error code of P0038


P0038 HO2S Heater Control Circuit High (Bank 1 Sensor 2) It is located behind the catalytic converter, in the exhaust pipe . P0038 HO2S Heater Control Circuit High Bank 1 Sensor 2

Nov 01, 2015 | 2005 Dodge Durango

1 Answer

How do I locate the Crank shaft sensor on a 2005 Dodge Durango


Have you looked on the transmission just behind the engine block? A lot of the Dodge vehicles get readings of the flexplate/flywheel.

Sep 12, 2014 | 2005 Dodge Durango

1 Answer

Where is the oil presser sensor located at on a 2005 dodge durango


The oil pressure sensor for the 4.7 screws into the block right next to oil filter which is on the front left side of the engine.

Jun 27, 2014 | Cars & Trucks

1 Answer

WHERE IS THE IAT SENSOR ON A 2005 DODGE DURANGO LOCATED AT?


The sensor is located either in the air filter box or in the air duct coming from the box going to the throttle body. Let me know if you need anything else.

May 07, 2010 | 2005 Dodge Durango

1 Answer

2005 dodge durango driving down the road,


Are you actually hearing the engine speed change as well when this happens, or just seeing the tach needle make crazy readings??

If only the tach is being funky, then I would say a speed sensor on the tranny is on its way out. There is also a speed sensor on the rear axle of some Durangos that can cause this issue.

Apr 21, 2010 | 2005 Dodge Durango

1 Answer

Check gages light came on driving a 2002 dodge durango now engines knocking


with engine running check the oil pressure gauge. if it is not reading you will have to check the pressure with an external gauge. the sensor on a v8 is locaterd rear of the engine next to the distributor. No oil pressure will starve the engine of lubrication and cause damage resulting in the knocking .

Dec 12, 2009 | 2002 Dodge Durango

1 Answer

2005 Dodge Durango knock sensor problems


I really doubt the knock sensor is the problem, check the connector 1st for water intrusion or oil, if u do replace it then u must torque it to the proper spec into the cooling system jacket of the block or it will set another code.

Mar 11, 2009 | 2005 Dodge Durango

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,006 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...