Question about 2004 Ford Focus

1 Answer

R/H rear quarter window repalcement

My rear quarter window is smashed. I bought a replacemant window, but how do I go about removing the old one and installing the new one? I bought window bead and RTV. Is that all I need to hold the window in?

Posted by on

  • 1 more comment 
  • admjet69 May 29, 2009

    I am an A&P mechanic. I can get B 1/2 if you think this mght be a better adhesive. I appreciate your help.

  • yadayada
    yadayada May 11, 2010

    have no idea what A&P means.

  • yadayada
    yadayada May 11, 2010

    this is for a glass shop, it takes special skills and adhesives to do this job

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 93 Answers

Tv is the wrong adhesive. you must use urethane with a primer. it is available at any QUALITY parts store (NAPA or Carquest comes to mind)


Material Item Specification Urethane Metal Primer Essex U-413
WSB-M2G234-C Urethane Glass Prep Essex U-401
WSB-M5B280-C Urethane Glass Primer Essex U-402
WSB-M2G314-B Urethane Adhesive Essex 400-HV
WSB-M2G316
Removal
All vehicles
R/H rear quarter window repalcement - ani_caut.gif WARNING: To prevent glass splinters from entering the eyes or cutting the hands, wear safety glasses and heavy gloves when cutting the glass from the vehicle.

  1. Remove the C-pillar trim panels. For additional information, refer to Section 501-05.
3-Door, 5-Door
  1. ani_caut.gif CAUTION: Make sure the cutting blades are changed where the cutting depth changes to avoid damage to the body and trim panels.
    NOTE: Some resistance may be encountered when cutting through the glass locating pegs in the lower corners of the glass.
    NOTE: Lubricate the existing urethane adhesive with water to aid the special tool while cutting.
    Using the special tool, place the flat side of the knife against the quarter glass window. Start at the top and work towards the corners cutting to the given maximum depths:
    1. 20 mm
    1. 60 mm
    1. 75 mm
    1. 90 mm
    a0074767.gif
    1. ani_caut.gif CAUTION: Make sure the cutting blades are changed where the cutting depth changes to avoid damage to the body and trim panels.
      NOTE: Some resistance may be encountered when cutting through the glass locating pegs in the upper right and lower left corners of the glass.
      NOTE: Lubricate the existing urethane adhesive with water to aid the special tool while cutting.
      Using the special tool, place the flat side of the knife against the quarter glass window. Start at the top and work towards the corners cutting to the given maximum depths:
      1. 20 mm
      1. 30 mm
      1. 40 mm
      a0074768.gif
    4-Door
    1. ani_caut.gif CAUTION: Make sure the cutting blades are changed where the cutting depth changes to avoid damage to the body and trim panels.
      NOTE: Some resistance may be encountered when cutting through the glass locating pegs in the upper right and lower left corners of the glass.
      NOTE: Lubricate the existing urethane adhesive with water to aid the special tool while cutting.
      Using the special tool, place the flat side of the knife against the quarter glass window. Start at the top and work towards the corners cutting to the given maximum depths:
      1. 20 mm
      1. 25 mm
      1. 45 mm
      1. R/H rear quarter window repalcement - a0074769.gifol>
        1. 55 mm
        1. 70 mm
        1. 150 mm
        a0074769.gif
      All vehicles
      1. Using a soft brush or vacuum, remove any dirt or foreign material from the pinch weld.
      Installation
      ani_caut.gif CAUTION: When installing urethane installed glass parts, the vehicle must not be driven until the urethane adhesive has cured. At temperatures above 21°C (70°F) and relative humidities above 50%, adequate cure time is typically 24 hours. (Refer to Essex drive away chart for the cure times as temperatures and humidity vary.) Inadequate or incorrect curing can adversely affect the retention of the quarter window glass.
      1. NOTE: Avoid sR/H rear quarter window repalcement - a0005586.gife pinch weld.
        Trim the remaining urethane adhesive. The urethane adhesive must be smooth and free of cuts and contamination after trimming. Avoid touching the urethane adhesive after preparation.
        a0005586.gif
      1. Apply the urethane metal primer to any exposed or damaged metal on the pinch weldR/H rear quarter window repalcement - ani_caut.gif
        1. If reinstalling the original rear quarter window glass, remove the excess urethane adhesive.
        1. Clean the rear quarter window glass with a non-alcohol based window cleaner.
        1. ani_caut.gif CAUTION: Wipe off the urethane glass prep immediately after each application because it flash dries.
          If installing a new rear quarter window glass, apply urethane glass prep twice around the glass surface to be uretR/H rear quarter window repalcement - a0016835.gif/ol>
          1. If installing a new rear quarter window glass, apply urethane glass primer to the same area that was prepped in the previous step. Allow 5 minutes to dry.
          1. Cut the urethane adhesive applicator tip to specification.
            a0016835.gif
          1. Position the rear quarter window glass to the flange, and press the retaining tabs into the flange to engage.
            an0459b.gif
          1. Install the rear quarter window glass.
          1. Check the rear quarter window glass installation for air or water leaks through the urethane seal.
          1. Install the C-pillar trim panels. For additional information, refer to Section 501-05.

Posted on Jun 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove and replace rear drivers side quarter glass 2004 Chevy impala


This video is not on an Impala, but a quarter window is a quarter window. It should give you an idea of what needs to be done.
How to Replace Quarter Window

Jan 28, 2017 | Chevrolet Impala Cars & Trucks

1 Answer

Replacing quarter glass on left side on 2005 pontiac gto


Remove the door opening weather-strip. Refer to Door Opening Weatherstrip Replacement in Doors.
Remove side sill trim plate. Refer to Door Sill Plate Replacement in Interior Trim.
Remove the lower quarter panel trim. Refer to Rear Quarter Trim Panel Replacement in Interior Trim.
Remove the center pillar upper trim panel. Refer to Center Pillar Upper Trim Panel Replacement in Interior Trim.
Remove the quarter upper trim panel. Refer to Rear Quarter Upper Trim Panel Replacement in Interior Trim.
Remove the center pillar outer applique. Refer to Center Pillar Applique Replacement in Exterior Trim.
Remove the roof drip molding. Refer to Body Side Roof Drip Molding Replacement in Exterior Trim.

Important: It is necessary to use new nuts when reinstalling the quarter window.
Remove the nine quarter window nuts (1), securing the quarter window assembly (2) to the body opening.
Caution: When working with any type of glass or sheet metal with exposed or rough edges, wear approved safety glasses and gloves in order to reduce the chance of personal injury.
Important: When removing the quarter window from the body opening make sure that the attaching pins are clear of the outer body.
Remove the quarter window (2) from the body opening.

Remove the rear seat cushion. Refer to Rear Seat Cushion Replacement in Seats.
Remove the rear seat back. Refer to Rear Seat Back Replacement in Seats.
Remove the door sill plate. Refer to Door Sill Plate Replacement .

Remove the 3 quarter trim panel retaining screws (1).
Starting at the lower edge of the trim panel and moving alternately clockwise and counterclockwise, pull outward on the trim panel to disengage the eight rear quarter trim panel attaching clips (2).
Remove the quarter trim panel from the vehicle.
Remove the 4 radio speaker grille speed clips (1), securing the speaker grille.
Remove the speaker grille (2).
Remove the rear quarter trim panel insulator (1), from the back of the quarter trim assembly (2).
Remove 7 rear quarter trim panel armrest retaining clips (1).
Remove 7 rear quarter trim panel armrest retaining nuts (2).
Gently pry the quarter trim panel armrest insert assembly (3), away from the rear quarter trim panel and remove.

You mite look for a video on youtube !

Dec 23, 2016 | Pontiac Cars & Trucks

1 Answer

How to install quarter window that flips out on 2003 dodge Dakota. 2 door.right side


REMOVAL

(1) Remove quarter trim panel.

(2) Remove the bolts attaching the latch to the cab


side panel.



(3) Remove the nuts attaching the frame/hinge to

the B-pillar.

(4) Remove the glass from the cab.
(5) If necessary, remove the latch from the glass.

INSTALLATION

(1) If removed, install the latch to the glass.

(2) Center the window glass at the opening, insert

the hinge studs in the B-pillar holes, and install the

nuts.

(3) Attach the latch to the rear side panel with the

bolts. Tighten the bolts with the latch in the lock

position and pushing rearward on the latch.

(4) Test the vent window for water leaks.
(5) Install quarter trim panel.

INSTALLATION

(1) If removed, install the latch to the glass.

(2) Center the window glass at the opening, insert

the hinge studs in the B-pillar holes, and install the

nuts.

(3) Attach the latch to the rear side panel with the

bolts. Tighten the bolts with the latch in the lock

position and pushing rearward on the latch.

(4) Test the vent window for water leaks.
(5) Install quarter trim panel.

Oct 02, 2016 | 2003 Dodge Dakota

1 Answer

Where is the motor located for my rear quarter panel windows on my 05 Pontiac Montana SV6? And how do I test it?


Rear Quarter Window Actuator - Right (A20)
Behind the right rear interior body panel
Rear Quarter Window Actuator - Left (A20)
Behind the left rear interior body panel
Rear Quarter Window Inoperative

1

Did you review the rear quarter window description and operation?
Go to Step 2
Go to Symptoms - Body Rear End

2

Verify that the rear quarter windows are inoperative.
Do the rear quarter windows operate normally?
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
Go to Step 3

3

Are both rear quarter windows inoperative?
Go to Step 4 yes
Go to Step 6 no

4

  1. Turn OFF the ignition.
  2. Disconnect the rear quarter window switch.
  3. Turn ON the ignition, with the engine OFF.
  4. Probe the accessory voltage circuit of the rear quarter window switch harness connector with a test lamp that is connected to a good ground.
Does the test lamp illuminate?
yes Go to Step 5
no Go to Step 7

5

Connect a test lamp between the accessory voltage circuit of the rear quarter window switch harness connector and the ground circuit of the rear quarter window switch harness connector.
Does the test lamp illuminate?
Go to Step 8
Go to Step 10

6

  1. Turn OFF the ignition.
  2. Disconnect the appropriate rear quarter window actuator.
  3. Turn ON the ignition, with the engine OFF.
  4. Connect a test lamp between the power window motor rear vents open control circuit of the rear quarter window actuator harness connector and the power window motor rear vents close control circuit of the rear quarter window actuator harness connector.
  5. Activate the rear quarter window switch to the Open and Close positions.
Does the test lamp illuminate?
yes Go to Step 9
no Go to Step 11

6

  1. Turn OFF the ignition.
  2. Disconnect the appropriate rear quarter window actuator.
  3. Turn ON the ignition, with the engine OFF.
  4. Connect a test lamp between the power window motor rear vents open control circuit of the rear quarter window actuator harness connector and the power window motor rear vents close control circuit of the rear quarter window actuator harness connector.
  5. Activate the rear quarter window switch to the Open and Close positions.
Does the test lamp illuminate?
yes Go to Step 9
no Go to Step 11

7

Test the accessory voltage circuit for an open or a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 14
Go to Retained Accessory Power (RAP) Inoperative in Computer/Integrating Systems

8

Inspect for poor connections at the harness connector of the rear quarter window switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
yes Go to Step 14
no Go to Step 12

9

Inspect for poor connections at the harness connector of the appropriate rear quarter window actuator. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
yes Go to Step 14
no Go to Step 13

10

Repair the open in the ground circuit of the rear quarter window switch. Refer to Wiring Repairs and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 14
--

11

Repair the open in the appropriate power window motor rear vents control circuit. Refer to Wiring Repairs and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 14
--

12

Replace the rear quarter window switch. Refer to Quarter Window Switch Replacement .
Did you complete the replacement?
Go to Step 14
--

13

Replace the appropriate rear quarter window actuator. Refer to Body Side Window Actuator Replacement .
Did you complete the replacement?
Go to Step 14
--

14

Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 2

Sep 28, 2015 | Pontiac Cars & Trucks

1 Answer

How to remove a rear quarter window, that's not a


You have to remove the Rear Panel, then the Window is bolted to teh Manual Window Regulator, Unbold and then pull out at an angle through the SLot

Apr 10, 2013 | Cars & Trucks

1 Answer

Best way to detatch a 2003 model celica quarter panel around the window?


You must remove the window and then pry the panel off, just drilling out the weld does not release the area around the weld.

Jul 26, 2012 | 2003 Toyota Celica

1 Answer

The left rear door window fell off the track. How do I remove the door panel to access it.


This is the complete procedure you stop when you see the problem.



1. REMOVE REAR DOOR INSIDE HANDLE BEZEL


(a) Remove the screw.


(b) Using a screwdriver with its tip taped, disengage the 2 claws A.


(c) Pull out the the rear door inside handle bezel in the direction indicated by the arrow, disengage the claw B, and remove the rear door inside handle bezel.


2. REMOVE DOOR PULL HANDLE


(a) Using a screwdriver wrapped with the protective tape, disengage the 2 clips and remove the door pull handle.


3. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


(a) Remove the screw.


(b) Disengage the 7 clips.


(c) Disconnect the connector and pull up on the rear door trim board sub-assembly to remove it.


4. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


(a) Remove the bolt.


(b) Disengage the 2 claws and separate the rear door inside handle sub-assembly.


(c) Disconnect the 2 cables and remove the rear door inside handle sub-assembly.


5. REMOVE REAR SPEAKER


6. REMOVE REAR DOOR SERVICE HOLE COVER


(a) Disconnect each connector and remove the rear door service hole cover.


HINT:


Remove the remaining tape on the door side.


7. REMOVE REAR DOOR GLASS RUN


(a) Connect the window regulator switch assembly.


(b) Fully lower the door glass.


(c) Remove the rear door glass run.


8. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


(a) Remove the 2 bolts, the screw and rear door window division bar sub-assembly.


9. REMOVE REAR DOOR QUARTER WINDOW GLASS


(a) Pull out the direction indicated by the arrow, remove the rear door quarter window glass and rear door quarter window weatherstrip as a unit.


10. REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP


11. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


(a) Remove the rear door glass sub-assembly as shown in the illustration.


(b) Disconnect the window regulator switch assembly.


12. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY


(a) Disconnect the connector.


(b) Loosen the temporary bolt.


NOTICE:


If the temporary bolt is removed, the rear door window regulator may fall and become deformed.


(c) Remove the 3 bolts and the rear door window regulator sub-assembly and the power window regulator motor assembly rear as a unit.


(d) Remove the temporary bolt from the regulator.


13. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY REAR


(a) Using a "torx" driver (T25), remove the 3 screws and power window regulator motor assembly rear.


14. REMOVE REAR DOOR LOCK ASSEMBLY


(a) Disconnect the connector.


(b) Remove the bolt.


(c) Using a "torx" socket wrench (T30), remove the 3 screws.


(d) Slide the rear door lock assembly downward, pull out the link from the outside handle frame, and remove the rear door lock assembly and cables as a unit.


(e) Remove the door wire harness packing.


(a) Using a "torx" socket wrench (T30), loosen the screw.


(b) Disengage the 2 claws and remove the rear door outside handle cover.


(a) Disengage the 2 claws and remove the rear door outside handle pad rear.

Jan 03, 2011 | 2006 Toyota Highlander

1 Answer

How to replace rear blower motor motor in 2006 chrysler town and country van


from autozone.com:


Removal & Installation

  1. Disconnect and isolate the negative battery cable.
  2. Remove the right quarter trim panel as follows:
    1. Remove first rear seat. Remove the second rear seat, if equipped.
    2. Remove the sliding door sill plate.
    3. Remove the quarter trim bolster.
    4. Remove the upper C-pillar trim and D-pillar trim panel.
    5. Remove the first and second rear seat belt anchors.
    6. Remove the screws securing the quarter trim to quarter panel from the bolster area.
    7. Remove the screws securing the rear edge of the quarter trim to the support bracket.
    8. Carefully disengage the hidden clips securing the front of the quarter trim to the quarter panel just rearward of the sliding door opening.


jturcotte_39.gif
Fig. Removing the trim panel to access the rear blower motor

i. Disconnect the wiring harness connector from the accessory power outlet, if equipped.


j. On long wheelbase wagons only, remove the quarter trim from the quarter panel and pull second rear seat belt through access hole.


k. Pull first rear seat belt through the access hole.


l. Remove the quarter trim panel from the vehicle.



3. Remove the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).


4. Twist the blower motor out of scroll housing.


5. Disconnect the blower motor wiring connector.


6. Remove the blower motor from vehicle.

jturcotte_40.gif
Fig. The rear blower motor is held in place by four screws
To install:

  1. Install the blower motor unit into the vehicle.
  2. Reconnect the blower motor wiring connector.
  3. Secure the blower motor into scroll housing.
  4. Install and tighten the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
  5. Install the right quarter trim panel as follows:
    1. Install the quarter trim panel in position in the vehicle.
    2. Insert and pull the first rear seat belt through the access hole in quarter trim panel.
    3. On long wheelbase wagons only, insert and pull the second rear seat belt through access hole in quarter trim panel.
    4. Reconnect the wiring harness connector to the accessory power outlet, if equipped.
    5. Engage the hidden clips to secure the front of quarter trim to quarter panel rearward of sliding door opening.
    6. Install the retaining screws that secure the rear edge of quarter trim to support bracket.
    7. Install the retaining screws that secure the quarter trim to the quarter panel in bolster area.
    8. Install the second rear seat belt anchor (if equipped), and the first rear seat belt anchor.
    9. Install the D-pillar trim panel and upper C-pillar trim.
    10. Install the quarter trim bolster.
    11. Install the sliding door sill plate.
    12. Install the second rear seat, if equipped, and install the first rear seat.
  6. Reconnect the negative battery cable. Check blower motor operation.

Nov 04, 2010 | Chrysler Town and Country Cars & Trucks

1 Answer

How to replace the blower motor in a dodge 2001 caravan


Removal & Installation
  1. Disconnect and isolate the negative battery cable.
  2. Remove the right quarter trim panel as follows:
    1. Remove first rear seat. Remove the second rear seat, if equipped.
    2. Remove the sliding door sill plate.
    3. Remove the quarter trim bolster.
    4. Remove the upper C-pillar trim and D-pillar trim panel.
    5. Remove the first and second rear seat belt anchors.
    6. Remove the screws securing the quarter trim to quarter panel from the bolster area.
    7. Remove the screws securing the rear edge of the quarter trim to the support bracket.
    8. Carefully disengage the hidden clips securing the front of the quarter trim to the quarter panel just rearward of the sliding door opening.

      1549e60.jpg

      Fig. Removing the trim panel to access the rear blower motor

    9. Disconnect the wiring harness connector from the accessory power outlet, if equipped.
    10. On long wheelbase wagons only, remove the quarter trim from the quarter panel and pull second rear seat belt through access hole.
    11. Pull first rear seat belt through the access hole.
    12. Remove the quarter trim panel from the vehicle.
  3. Remove the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
  4. Twist the blower motor out of scroll housing.
  5. Disconnect the blower motor wiring connector.
  6. Remove the blower motor from vehicle.

    823bf07.jpg

    Fig. The rear blower motor is held in place by four screws


To install:
  1. Install the blower motor unit into the vehicle.
  2. Reconnect the blower motor wiring connector.
  3. Secure the blower motor into scroll housing.
  4. Install and tighten the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
  5. Install the right quarter trim panel as follows:
    1. Install the quarter trim panel in position in the vehicle.
    2. Insert and pull the first rear seat belt through the access hole in quarter trim panel.
    3. On long wheelbase wagons only, insert and pull the second rear seat belt through access hole in quarter trim panel.
    4. Reconnect the wiring harness connector to the accessory power outlet, if equipped.
    5. Engage the hidden clips to secure the front of quarter trim to quarter panel rearward of sliding door opening.
    6. Install the retaining screws that secure the rear edge of quarter trim to support bracket.
    7. Install the retaining screws that secure the quarter trim to the quarter panel in bolster area.
    8. Install the second rear seat belt anchor (if equipped), and the first rear seat belt anchor.
    9. Install the D-pillar trim panel and upper C-pillar trim.
    10. Install the quarter trim bolster.
    11. Install the sliding door sill plate.
    12. Install the second rear seat, if equipped, and install the first rear seat.
  6. Reconnect the negative battery cable. Check blower motor operation.

Hope helps (remember to rate this).

Nov 01, 2010 | 2000 Dodge Caravan

Not finding what you are looking for?
2004 Ford Focus Logo

2,874 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...