Question about 2000 Ford Explorer

1 Answer

How do I remove the left side mirrer on my 2000 ford explorer?

What do I need to do to replace the mirrer?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 93 Answers

Mirror — Outside Rear View Removal
NOTE: Do not remove the exterior mirror assembly when repairing an individual part. Individual components can be installed without removing the exterior mirror.

  1. Disconnect the battery ground cable (14301).
  1. Remove the front door trim panel; refer to Section 501-05.
  1. Remove the speaker.
    1. Remove the screws.
    1. Disconnect the electrical connector.
    1. Remove the speaker.
    How do I remove the left side mirrer on my 2000 fo - gk6980a.gif
  1. Remove the outside rear view mirror (17682).
    1. Disconnect the power mirror wiring clips.
    1. Remove the outside rear view mirror nuts.
    1. Remove the outside rear view mirror.
      • Feed the power mirror wiring through the opening in the front door (20124).
    gn0316a.gif
Installation
  1. NOTE: When the battery (10655) is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
    To install, reverse the remHow do I remove the left side mirrer on my 2000 fo - gn0317a.gifure.
    gn0317a.gif

Posted on Jun 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On a 2000 explorer 4.0 Soho do I have to remove the injectors to remove the lower intake


REMOVE UPER INTAKE 97 EXPLORER V6 4.0 - YouTube

? 12:22
https://www.youtube.com/watch?v=ugExJ0wkP8A
Jun 11, 2013 - Uploaded by Sum Guy
REMOVE UPER INTAKE 97 EXPLORER V6 4.0 ... I was told that all I have to do is remove the fan belt to get access to it ... FordExplorer 2000 intake manifold gasket upper lower P0174 by froggy - Duration: 36:54. by froggy 36,588 views ... Ford Explorer 4.0L SOHC Rough Idle P0171 P0174 Lean Codes ...

Putting the lower intake on my 1997 Ford Explorer 4.0 OHV ...

? 5:23
https://www.youtube.com/watch?v=qKE1vPxqPHs
Jun 27, 2010 - Uploaded by origionaldz
Putting the lower intake on my 1997 Ford Explorer 4.0 OHV sport .... I do have a 2000 5.0 ... @michaelheiland123654 To dothis job, you have to remove the alternator, unbolt the AC compressor, remove upper intake manifold, remove fuel rail,remove all injectors, ... Do you have the SOHC or OHV version?

1999 Ford Explorer 4.0L -need assistance on removing upper intake ...

www.automotiveforums.com > ... > Ford > Explorer ' Explorer Sport Trac
Sep 20, 2011 - 1999 Ford Explorer 4.0L -need assistance on removing upper intake ...Are you sure you have the OHV/pushrod engine and not the SOHC engine? ... Do youhave the upper intake manifold loose, you just are unable to ... the lower intake gasket, valve cover gaskets, Injector o-rings, plugs and wires. Thanks ...

How to replace upper intake manifold gaskets - Ford Explorer




Dec 09, 2015 | Cars & Trucks

1 Answer

Where is the dpfe sensor located on the 2000 ford taurus?


I had to replace the dpfe sensor on my 2000 Ford Explorer and they should be the same.
Mine was located on the left side of the engine (facing the engine with the hood up) above the valve cover. It will have two 3/8" vacuum lines going into it and a plug ended cable. Very simple to replace.

May 16, 2011 | 2000 Ford Taurus

1 Answer

Where is fuse box on 2000 explorer xlt


You have two locations,:
Fuse Panel: located on the left hand side of the instrument panel facing the drivers side door. Pull panel cover outward to access the fuses.Open side
Power Distribution Center: in the engine compartment.

For mode tails and graphics, can check the 2000 Explorer Owners Manual. (page 192 and next).

Good luck (rated this).

Jan 18, 2010 | 2000 Ford Explorer

1 Answer

I need to know which coils is number 8 on my ford explore 2000


Hello tmac200968: My name is Roger and I can answer your question for you. You will find #8 cylinder located on the driver side of the motor. THis will be the plug closest to the firewall. THe cylinders run as follows. 1-2-3-4 are on the right side of the block 5-6-7-8 are on the left side of the block.Right and left are always determined from the drivers seat. Please rate the quality of your answer as this is how we determine you received the correct information. Thank You for using FixYa. Roger

May 07, 2009 | 2000 Ford Explorer

3 Answers

1998 Ford Explorer timing problem


FORD: 1997-2000 EXPLORER, MOUNTAINEER
ISSUE: A "knocking" noise at start up for up to 2 minutes from the left hand front chain cassette area may occur on some vehicles. After engine shutdown, the tensioner oil supply gallery empties. The noise may be due to air entering the left hand tensioner when the engine is restarted.
ACTION: Replace the left hand camshaft tensioner with a revised Tensioner Kit. Refer to the Instruction Sheet within the Tensioner Kit for service procedure details.
tx2605~us~en~file=caution.gif~gen~ref.gif WARNING: THE XU2Z-6K254-AA TENSIONER KIT IS FOR INSTALLATION ON THE LEFT SIDE OF THE ENGINE ONLY. INSTALLATION OF THIS KIT ON THE RIGHT SIDE OF THE ENGINE MAY RESULT IN ENGINE FAILURE. IF A TENSIONER IS NEEDED FOR THE RIGHT SIDE OF THE ENGINE, USE KIT XU3Z-6K254-BA.
PART NUMBER PART NAME XU2Z-6K254-AA Tensioner Kit - Left Side XU3Z-6K254-BA Tensioner Kit - Right Side

SECTION 303-01B: Engine — 4.0L SOHC 1998 Explorer/Mountaineer Workshop Manual
IN-VEHICLE REPAIR Timing Drive Components —LH Hydraulic Chain Tensioner Removal and Installation
  1. Remove the upper intake manifold. For additional information, refer to Intake Manifold—Upper in this section.
Intake Manifold —Upper Removal
  1. Disconnect the battery ground cable (14301). For additional information, refer to Section 414-01 .
  1. Remove the air cleaner outlet tube (9B659); refer to Section 303-12 .
  1. Remove the bolts and the accelerator control splash shield.
  1. Remove the accelerator cable (9A758) and speed control actuator cable (9A825).
    1. Pull up on speed control actuator cable to remove.
    1. Rotate the throttle body cam and remove the accelerator cable from the cam.
  1. Remove the screws, the accelerator cable and speed control actuator cable.
  1. Disconnect the RH upper intake manifold vacuum connection.
  1. Disconnect the idle air control (IAC) valve electrical connector.
  1. Disconnect the TP sensor electrical connector.
  1. Disconnect the engine vacuum regulator (EVR) and the variable induction system (VIS) solenoid electrical connections.
  1. Disconnect the crankcase ventilation hose (6853).
  1. Disconnect the power brake booster vacuum line.
  1. Remove the 12 bolts.
  1. NOTE: Inspect the O-rings and replace as necessary.
    Disconnect the LH fuel vapor management valve (VMV) hose.
  1. NOTE: Inspect the O-rings and replace as necessary.
    Disconnect the RH VMV hose and remove the upper intake manifold.
  1. Remove the thermostat housing. For additional information, refer to Section 303-03 .
  1. Remove the LH camshaft tensioner.
    • If using a new washer, tighten to 44 Nm (32 lb-ft).
    • If using the old washer, tighten to 67 Nm (49 lb-ft).
  1. Remove the pipe plug, and the oil volume reduction plug.
  1. NOTE: Be sure to install the new oil volume reduction plug supplied with the hydraulic chain tensioner.
    To install, reverse the removal procedure.
please rate as fixed if this helps you

May 03, 2009 | 1998 Ford Explorer

1 Answer

I need to replace the drivers side mirror on a ford explorer 2000....how is this done? I know you take it off, but does the inside door panel come off?


you remove door trim panel and the plastic water shield .disconnect electrical connectors from the mirror.peel back insulator pad .then remove the mirrors 3 retaining nuts remove the mirror.

Apr 24, 2009 | 2000 Ford Explorer

2 Answers

Recognizing ford models, namely 2000 explorer


Check the VIN plate in the lower left corner of the dash (driver side) and viewed from outside of truck through windshield. The 11th digit of the VIN should be a letter " Y " which indicates a model year 2000. The VIN number should also be on a label on the driver side door or B post.

Mar 21, 2009 | 2000 Ford Explorer

1 Answer

2000 Ford Explorer 6 cyl


pcv is located at rear of valve cover on drivers side.to remove turn counterclockwise then pull.be very careful because there are 2 small lock tabs to hold valve in place.

Oct 21, 2008 | 2000 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

421 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...