Question about 1991 Toyota 4Runner

1 Answer

Stuck clutch 93 ford ranger sat for two years. clutch will not disengage know.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 318 Answers

The clutch has rusted to the flywheel drive the truck down the road you will have to start it in gear (1st) while driving push the clucth pedal to the floor and keep pushing up and down on the gas pedal to get the truck to rock forwards and backward the clutch should brake loose.

Posted on May 29, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

After driving down bumpy road my clutch does not seem to disengage, after it sits awhile it works fine, 2009 ford ranger

The hydraulic fluid level in the clutch master cylinder may be low. The rough ride can cause the fluid to fill with air bubbles. If the fluid has air in it, it will not compress properly and therefore the clutch will not disengage.

Mar 29, 2017 | Ford Ranger Cars & Trucks

1 Answer

I have a 93 ford ranger four cylinder that set for a year or two now the clutch is extreamly soft and light grab what could be problem

This should have a hydraulic clutch look for a leak in the line from the inside all the way down to the clutch if the pump is empty add fluid pump it a few times and locate the leak post your finding good luck

Sep 26, 2014 | Cars & Trucks

1 Answer

2002 ranger ac.

Could be a stuck relay, or the ac clutch.
Will the clutch disengage if you unplug it ?

May 30, 2013 | 2004 Ford F150

1 Answer

Clutch would not disengage

IF you have bled the clutch system and managed to get a firm clutch then the clutch plate has been installed back to front and the clutch center is hitting the bolts that hold flywheel onto the crankshaft. If you have no not got a firm predal pressure replace the clutch master cyl

Mar 02, 2013 | 1989 Ford Ranger

1 Answer

1990 f-250 truck has sat alot the clutch wont disengage it seems.mastercylinder looks full?

This happens to many cars that sit too long. The clutch plate has probably stuck to the flywheel. Just put the transmission in neutral and with engine and brake off, try rocking the car back and forth. If alone, be sure that you are not on a hill, because when the clutch breaks loose, the car will roll freely.

Oct 31, 2010 | 1986 Ford F 250

1 Answer

Should I take my '93 ford ranger to a transmission shop to replace the clutch?

Hi, you should definitely take it to a transmission shop to replace the clutch, you will get the best of service like i did....

Take care

Aug 01, 2010 | 1993 Ford Ranger SuperCab

1 Answer

1987 Ford Ranger stuck in 4 wheel drive!!

Chances are the linkage for the transfer case is out of adjustment try loosening the adjuster bolt and put the 4WD shifter into the position 4WD high or low (depending upon which position it's lockup in) then lock down the adjuster bolt, try to shift out of 4wd sometimes you need to go forward and backward with the vehicle to get it out of 4wd, when you get it out of 4wd you may have to fine tune the adjustment to get it to engage and disengage smoothly it's a trial and error thing keep resetting adjuster until you get the desired effect.

Jul 02, 2009 | Ford Ranger Cars & Trucks

1 Answer

5speed ford ranger problem is shifting

Sounds like your clutch is not releasing enough to allow you to engage or disengage. It is dragging which causes hard engagement and disengagement. Possible causes are, Low fluid in the master cylinder to the clutch, or bad slave cylinder down by the bell housing, or badly worn pressure plate, or air in the line leading to the slave cylinder. You will need to eliminate these items one by one by testing to find the bad item in the system. Good luck

Apr 14, 2009 | Ford Ranger Cars & Trucks

1 Answer

87 ranger new motor bad truck

try to find an 1988======>93 ranger. the closer to 88 the better. the wiring harness is similar in 90-93, but you will have to adapt some parts on the newer.

Sep 10, 2008 | 1988 Ford Ranger

Not finding what you are looking for?
1991 Toyota 4Runner Logo

565 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8582 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides