Question about 1993 Mitsubishi Eclipse

1 Answer

Roar after new install

A roar after new clutch,pressure plate and release/throwout bearing no pull power at all!!

Posted by on

  • katiej_20080 May 29, 2009

    could it be the trans its self i'm more of a fourwheeler bike guy then i am cars!!!=]

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,559 Answers

Something is not installed properly

Posted on May 29, 2009

  • Randy Hough
    Randy Hough May 29, 2009

    Sounds more like the flywheel was not mounted the same way it came off and is now unbalanced.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Clutch stays down. Slowly will take of with clutch fully pressed. Does not slip.dont understand


It sounds as though the clutch pressure plate has become weak.

When you press the clutch pedal the release/throwout bearing presses against the centre of the clutch pressure plate. This causes the metal 'fingers' -the springs- on the pressure plate to flex and release pressure on the driven plate - momentarily disconnecting the drive from engine to gearbox.

The link below is of generic clutch images
how clutch works Google Search

A weak pressure plate isn't fully releasing the driven plate. If you're going to do any replacing of parts - a clutch should be replaced in 3 units: Pressure plate, driven plate and release/throwout bearing.

May 05, 2016 | Cars & Trucks

1 Answer

Hi i just put a new master cylinder a month back now today my clutch felt hard and when i put it in reverse heard a broken sound clutch went flat and oil came from the master what can the problem be


Umm...

A mechanical 'breaking noise' doesn't sound good. It's hard to diagnose a problem online without being there to see/hear the vehicle. But .. it may be that your clutch pressure plate has broken/ release/throwout bearing has broken?

It's difficult to see why the master cylinder should leak - unless it was incorrectly fitted in the first place?

Just to check ... The master cylinder is in the engine bay/compartment and is where you top up with clutch fluid. When a master cylinder fails it usually results in no pressure at the clutch pedal, not a leak.

The clutch slave cylinder is the one that does all the work. When you press the pedal hydraulic pressure is sent from the master cylinder to the slave cylinder - which then pushes the release/throwout bearing against the clutch pressure plate and 'disconnects' the driven plate .. allowing you to change gear.

The slave cylinder is the one that does all the hard work - it is located somewhere where engine and gearbox mate together, usually at the bottom right/left. It's usually the one that fails/leaks. It's quite easy to replace..

I don't think it is anything to do with reverse gear. It's more to do with the clutch pedal being depressed - and, I would suspect - something has failed.

The link below is generic images of a clutch:
clutch diagram Google Search

Basically, a clutch is 3 parts. There's the 'pressure plate' which bolts onto your flywheel. The pressure plate is a 'spring'. You depress the clutch pedal and the release/throwout bearing presses onto the centre of the pressure plate causing the 'fingers' - the springs - to bend back and take pressure off the driven plate - which is the link - the drive - between engine and gearbox.

If you have a leak your clutch will not work. This causes a 'grinding/crashing' noise when you try to change gear. The first thing you should do is check where the leak is coming from and do something about it.

The 'noise' that you mention may be due to the fact that the gears are 'grinding' as they try to mesh together without the use of the clutch.

The first thing you should do is check why there's a leak. It's difficult to see why a new master cylinder is leaking unless it was incorrectly fitted and damaged (pipes incorrectly connected..).

If it's the slave cylinder that is leaking - replace it. Easy job.

If Master cylinder and slave cylinder are ok - you have to look at your clutch unit. A clutch is always replaced with 3 parts ... throwout bearing/pressure plate and driven disk.

May 04, 2016 | Cars & Trucks

1 Answer

I need to know how to replace the clutch in a 1993 colt vista


0900c1528004723e.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: Clutch release bearing - 1990 Colt hatchback and sedan w/ 1.6L engine, 1990 Colt Wagon w/1.8L engine, and 1990-93 Vista


0900c1528004723f.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 2: Clutch driven and drive discs - 1990-93 all models


0900c15280047240.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: Clutch release bearing - 1990 Colt Wagon w/1.5L engine, 1991-92 Colt hatchback and sedan w/4-speed and 1993 Colt hatchback and sedan w/1.8L engine

  1. Remove the transmission or transaxle as outlined.
  2. Insert a pilot shaft or an old input shaft into the center of the clutch disc, pressure plate, and the pilot bearing in the crankshaft.
  3. With the pilot tool supporting the clutch disc, loosen the pressure plate bolts gradually and in a crisscross pattern.
  4. Remove the pressure plate and clutch disc.
  5. Clean the transmission and clutch housing. Clean the flywheel surface with a non-oil based solvent. Wash your hands before installing or handling the clutch assembly parts. Hold the clutch disc by the center hub only.

Before assembly, slide the clutch disc up and down on the transmission input shaft to check for any binding. Remove any rough spots with crocus cloth and then lightly coat the shaft with Lubriplate.
  1. To remove the throwout bearing assembly: Remove the return clip and take out the throwout bearing carrier and the bearing.
  2. To replace the throwout arm use a / 16 in. punch, knock out the throwout shaft spring pin and remove the shaft, springs, and the center lever.
  3. Do not immerse the throwout bearing in solvent; it is permanently lubricated. Blow and wipe it clean. Check the bearing for wear, deterioration, or burning. Replace the bearing if there is any question about its condition.
  4. Check the shafts, lever, and springs for wear and defects. Replace them if necessary.
  5. If you hadn't planned on replacing the clutch disc, examine it for the following before reusing it. Loose rivets. Burned facing. Oil or grease on the facing. Less than 0.3mm left between the rivet head and the top of the facing.
  6. Check the pressure plate and replace it if any of the following conditions exist: Scored or excessively worn. Bent or distorted diaphragm spring. Loose rivets.
  7. Insert the control lever into the clutch housing. Install the two return springs and the throwout shaft.
  8. Lock the shift lever to the shaft with the spring pin.
  9. Fill the shaft oil seal with multipurpose grease.
  10. Install the throwout bearing carrier and the bearing. Install the return clip.
  11. Grease the carrier groove and inner surface.
  12. Lightly grease the clutch disc splines.

The clutch is installed with the larger boss facing the transmission.
  1. Support the clutch disc and pressure plate with the pilot tool.
  2. Turn the pressure plate so that its balance mark aligns with the notch in the flywheel.
  3. Install the pressure plate-to-flywheel bolts head-tight. Using a torque wrench and, working in a crisscross pattern, tighten the bolts to 11-15 ft. lbs.
  4. Install the transmission or transaxle as outlined.
  5. Adjust the clutch as described in the following information.

Jan 07, 2013 | Cars & Trucks

1 Answer

No clutch disengagement


I hate to say it, but it could be an exploded throwout bearing or defective pressure plate/disc. Fixed one the other day, all new hydraulics, good travel at the fork, pulled trans to find throwout bearing in pieces. Hope this helps.

Oct 02, 2012 | Cars & Trucks

1 Answer

How do I replace a clutch 2000 eclipse


Remove transaxle. Remove clutch pressure plate. Remove clutch plate. Inspect the flywheel for damage and resurface or replace as necessary. Replace pilot and throwout bearings. Install new clutch plate. Install new pressure plate. Re-install transaxle.

Mar 06, 2012 | 2000 Mitsubishi Eclipse

2 Answers

Push in clutch and it makes a horriable grinding noise/ when release it stops and it goes into gear


It sounds like your throwout bearing is shot. There is a bearing called a throwout bearing that goes against the clutch forks when you push on the clutch, which causes the pressure plate to release the clutch which also releases tension from the input shaft which lets you change gears.
Replace that throwout bearing and I think you will find all your troubles gone. Hopefully it hasnt ruined the pressure plate forks. if your pressure plate forks are good there is not need to replace the clutch though if there is lots of miles on it you might choose to go ahead and do it since the transmission will be out anyway. Of course that is a lot more money. the choice is yours though so dont let a shop talk you into it if you dont want to.
Cheers.

Apr 21, 2010 | 1991 Nissan Pickup

1 Answer

I was bleeding my clutch now my clutch pedal stuck to the floor on a 1995 f 150


Most modern clutches are hydraulic. It may be that either the clutch master cylinder or slave cylinder are stuck or some sort of restriction in the line. Or, it may be that the throwout bearing or pressure plate have some sort of issue (this requires pulling the tranny and looking at the clutch, pressure plate (plate that rides against the clutch with springs to engage the clutch) and throwout bearing (bearing on the arm that presses against the pressure plate to engage the clutch).

Of course, I am assuming you have checked for any outside restrictions that would not allow the pivot arm to retract (missing spring or piece of ice or debris stuck in there).

Just some ideas :)

Jul 27, 2009 | 1995 Ford F150 Styleside Regular Cab

1 Answer

TRAns prob.. 93 mitsubishi eclipse..


This usually indicates a pressure plate spring is bound up and/or throwout bearing. Here are a few things to check...You are certain there is no air in the system, including slave cylinder....The pedal free play adjustment is important as well. On the Galant there is a locknut you loosen, then turn the pushrod until the freeplay is correct.
Did you move the release bearing lever to engage the release bearing with the wedge collar on install? Clutch plate facing the right direction? Did you have the flywheel resurfaced? Input shaft on transmission ok? Will the car roll in gear?
Good luck..i hope this helps.

May 29, 2009 | 1993 Mitsubishi Eclipse

1 Answer

New Clutch, New Noise!


throw out baring was inproperly installed

Mar 30, 2009 | 1998 Ford Escort

1 Answer

94 chevy s-10 clutch won't release comepletely after replacement


two things to mind, sometimes when you get a new clutch it comes with blocks in pressure plate there put in there from the factory for shipping purposes, they have to be removed otherwise it will do what you discribe. secound if you got the wrong length throwout bearing will do it to. most likely its one or the other. if you sure everything is right as far as clutch, pressure plate, and throwout bearing, than the only other thing i can say it could be is slave cyl. bad. hope this helps. OLD SCHOOL.

Jan 21, 2009 | 1994 Chevrolet S-10

Not finding what you are looking for?
1993 Mitsubishi Eclipse Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...