Question about 1992 Toyota Camry V6

1 Answer

How to change rear wheel bearings on 1992 toyota camry

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 136 Answers

Remove the wheel, disconnect the a arms upper and lower, tie rod end,brake caliper, remove the hub, remove wheel bearing, replace, repack, and re install

Posted on May 28, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to replace both lateral links on 96 toyota camry


See here for details, p89

http://www.turboninjas.com/camry/sa.pdf



Sometimes parts can be rusted in place, needing violence on your part


http://www.toyotanation.com/forum/103-3rd-4th-generation-1992-1996-1997-2001/375660-rear-wheel-wobble-how-diagnosis-replace-bad-lateral-control-arm.html#post3510098



If you decide to work on the front side lateral arms (still rear of car), that's when it gets REALLY hard


http://www.toyotanation.com/forum/103-3rd-4th-generation-1992-1996-1997-2001/372696-92-camry-help-advice-replacing-rear-lateral-control-arm-front-arm.html

Nov 28, 2012 | Toyota Camry Cars & Trucks

1 Answer

I have a Toyota Camry 1992. The car runs okay, but when I stop the wheel start to vibrate really hard, it doesn't do it when I accelerate the car or it is in Parking.


Hi,
This is usually due to warped/worn brake discs/rotors. Time to have a brake job done.

It could also be the wheel bearings. It will require a mechanic to fix.

Td

Nov 21, 2012 | Toyota Corolla Cars & Trucks

1 Answer

Oil leaking from toyota camry 1992, 1994 model


You don't say what engine it has. The 4-cyl was a better than the V6 for oil leaks.

The V6 had oil leaks from

-rear bank cam cover gasket

-distributor o-ring seal

-oil filter bracket o-ring seal

-crankshaft nose oil seal (less common)

-rear main bearing oil seal (expensive, just leave it)

The 4 cyl leaked oil from

-distributor o-ring seal

-camshaft cover gasket

-rear main bearing seal (expensive, leave it)

May 21, 2012 | 1991 Toyota Camry

3 Answers

It makes a grinding noise and only on the passenger side. just started making noise when turning


Check brakes, then check axle bearing. If brakes check out OK, then jack up so the wheel is off the ground, put car in neutral, now spin the wheel and put one hand on the coil spring, if you feel any roughness, the bearing is bad.

Nov 03, 2009 | 1992 Toyota Camry V6

1 Answer

Not-too-loud roar sounding


could be a wheel bearing. get the car up where you can spin the wheel, now grab the strut spring with your hand and spin the wheel. you will be able to feel "roughness" on the wheel that has a bad bearing.

Oct 13, 2009 | 2001 Toyota Camry

1 Answer

How to replace the wheel bearing in a 1992 toyota camry


Which one????? back is o.k you can do, frt forget it pressed in !

Aug 16, 2009 | 1991 Toyota Camry

1 Answer

Change the front wheel bearings toyota corolla 1992


front wheel bearings on this vehicle are part of a hub assy. you will have to completely remove the steering knuckle, press out the old bearing hub and rear seal and press in the new one.

Aug 03, 2009 | 1993 Toyota Corolla

1 Answer

How to change a rear wheel bearing on a 1994 toyota camry


The rear wheel bearing on a toyota camry is replaced by replacing the wheel bearing and hub as a unit. this is a design change as compare to older models with two piece wheel bearings. Scotch drive wheels. Remove rear wheel. Remove rear brake drum. (note: if emergency brakes are applied you will not be able to remove brake drum) Remove dust cap and hub retaining nut. Hub should slide off as unit. Replace hub with new unit. Installation is reverse of removal.

May 30, 2009 | 1994 Toyota Camry

Not finding what you are looking for?
1992 Toyota Camry V6 Logo

669 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...