I have a 93 deville and i just bought another keyless entry remote. i tried programing it by putting a paper clip in slots of my aldl connector but that didnt do anything. also i not even sure i found the aldl connector, the thing i found was under the dash behind the ashtray and it has 12 pin slot but only 6 active wires, so i dont know which one is "a" or "g" but i tried them all. I was reading and i sw another route i could go by putting it in diagnostic mode via climate control center. i just dont know the details on how to do it that way, any suggestions?
An expert who has achieved level 3 by getting 1000 points
An expert that got 10 achievements.
An expert that got 5 achievements.
An expert whose answer got voted for 100 times.
Re: keyless entry program
You jump terminal G (purple and white wire) and terminal A (black and white wire) doors should lock and unlock then press any button on the key fob and the locks should lock and unlock and you are done take jumper out
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need. goodluck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Put key remote near the ignition switch. Disconnect the battery for 30 minutes and reconnect. It SHOULD reset the chip in the ignition to match the remote and they should then be recognised by the ECM.
I own a 2007 Buick Lacrosse, but I imported it to Paraguay, South America. Now I bought a new Engine Start Keyless Entry Remote from Amazon, but here we do not have any GM dealer to program the unit.
I really need help to program the keyless remote control, I will appreciate very much your help.
you have to use a paper clip and bridge #4 and #8 terminals on the OBDII connector (then turn key on), then hold the lock/lulock buttons at the same time-the terminals are the top row, 4th and 8th(end) from the left side of the connector. Horn will beep 3 times when the code is learned by the new remote.
Hello: The keyless entry feature was NOT a factory option available on the 1989 Cadillac SedandeVille. If you have keyless entry it has to be after market. you will have to find out who made the add on unit and how to program it. SORRY
Hello, To answer your question about programming a keyless entry remote you need a scanner tool that has the capability to accomplish this task. A GM Tech 2 or something else that has the ability to do what the Tech 2 does. I know this is not what you want to hear but I am reading it right out of the Cadillac Service Manual. Thank you
reading your post you mention to "open and close switch"..not sure what refering to...these are the instructions from your vehicles service manual...good luck!
NOTE: All keyless entry remote transmitters (15K601) are programmable and must be set at the same time. NOTE: To program (or reprogram) the keyless entry remote transmitters into the RAP module, perform the following steps:
Make sure that the anti-theft system is not armed or triggered.
Turn the ignition switch (11572) from OFF to RUN eight times within ten seconds, ending in RUN. If the RAP module has successfully entered program mode, it will lock and then unlock all doors.
Press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed.
If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Diagnosis and Testing.
Turn the ignition switch to the OFF position, or wait up to 20 seconds after step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the RAP module will lock and unlock all doors one last time to confirm.
On this model you will have to open glove box and press the tabs on each side so that you can open it all the way open. You will see a 2 wire grey connector behind it.
Turn ignition switch to run postion then take a paper clip or something like that and momentarily short the 2 wires together.
The door locks should then cycle from lock to unlock.Remove the paper clip then press one of the buttons on each remote. When you press the button on the remote door locks should cycle again to confirm that it programed.Then when finished turn off the ignition switch and door locks should unlock to confirm you have exited programming mode.
on the plug in point on the car where they connect scan tool use pin 4 and 8 jump them with papper clip this will cause door locks to lock and unlock then press both lock and unlock buttons on fob and it will take programing then remove paper clip all done.