Question about Dodge Neon

1 Answer

I just got the clutch kit and installed it. The clutch engages once the pedal hits the floor board. It should engage at least a little off the floor, right?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 130 Answers

Yes very correct.it should engage at least a little of the floor.its not fitted properly.get it reallighned.
thaks.please do rate the solution.thank you for using fixya.

Posted on May 28, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to adjust 95 geo tracker clutch


engaging?
you meant dis-engage im sure.
pedal up is engaged,
pedal at floor dis-engages it.
my guess, is the clutch drags unless i push the clutch pedal 100%
to the floor.
1: bad cable is 90% cause. non last this long.
2: no free play is way too loose.
3: broken lever on the pedal top. caused by #1

all fail modes covered here.
http://www.fixkick.com/tranny/clutch/clutch-on-kick.html

Apr 23, 2014 | Geo Tracker Cars & Trucks

1 Answer

Clutch pedal travel


Your pedal height may be adjustable by a stopper bolt at top of pedal. You would have to check the specification for your car. Most important that the pedal has about a half inch free travel before clutch begins to engage. You need that free play to ensure the release bearing (the throw-out bearing) is not touching the fingers on the pressure plate when not engaged. If it always is touching, it will be rolling around constantly and will go out prematurely.
Your new clutch will allow gear engagement sooner as the clutch pedal is released. I mean gears will engage just as pedal is lifting off from floor. You should notice that difference-the old clutch would have taken longer pedal travel from floor before releasing.

Apr 15, 2013 | Cars & Trucks

2 Answers

My clutch is barely engaging even when depressed all the way to the floor. Can it be adjusted or dose it need a clutch replacement?


I would try adjusting the clutch master such that the point of engagement at the pedal, is further from the floor. This will effectively increase the travel of the clutch slave and possibly solve your problem. The clutch master pushrod should have an adjustment behind the pivot at the pedal bracket. Usually a lock nut has to be loosened off a little and then the rod screwed out of it's holder to effectively lengthen it.

Jan 24, 2011 | 1999 Suzuki Grand Vitara

1 Answer

Clutch issue after throwout bearing instal


once you have bled out all the air ,if the pedal still engages right down then suspect the fingers on the release plate are worn.Never replace a part of the clutch, allways change all 3 components,it save all the hastle of taking it to bits again and again.

May 21, 2010 | 2003 Nissan 350Z

2 Answers

Height of Clutch Pedal


I assume it is a cable operated clutch. If so the adjustment is tightened so that there is about 1/2 to 1" of pedal travel to clutch operation, provided the gears can be selected smoothly.

Mar 09, 2010 | 1987 Suzuki Samurai

1 Answer

Problem going into gear


Your clutch system works the same as brakes do. The necessity to bleed tells you that there is a malfunction permitting air into the system. Check where the pedal rod goes into the firewall under the dash, the line itself, and the slave unit (some are inside the bellhousing...look for fluid dripping from bottom to verify if leaking) Not unlike brake master, they can also internally bypass. If you find no leaks, change master. Bleed system and you should be fine

Jul 11, 2009 | 1995 Jeep Wrangler

2 Answers

Clutch ONLY engages close to the floor - how do I fix it?


Try to adjust the clutch to compensate. if the adjustments have already been made and, the pedal is very close to the floor while engaging. this will confirm pressure plate failure.

replace the pressure plate in this case.

Jun 20, 2009 | 1993 Volvo 240

1 Answer

Soft clutch 1992 isuzu rodeo


If the seals around the shafts of master and slave are tight, they may be concealing a leak with fluid bypassing the piston seals internal to the two assemblies. Either your master or slave cylinders need to be replaced ot have new seals installed. Once you find the culprit and have installed a replacement, you will have to bleed the lines to evacuate air trap in the lines.

Mar 21, 2009 | 1992 Isuzu Rodeo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...