Question about 1999 Mercury Villager

1 Answer

Engine motor mounts are loose. How do I tighten?

Can you show me where yhey are?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mercury Master
  • 4,369 Answers

You have 2 engine and one trans mount. Go here and check files and photos http://autos.groups.yahoo.com/group/villagerquest/

Posted on Jun 11, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the motor months for a 93can Dakota n how do fix it


They'll be at the bottom of your engine, one on each side and possible one at one end. One piece will bolt to the side of the engine block, and one piece will bolt to the truck's frame. Between the two pieces will be a rubber vibration damper.

If you need to replace one or more motor mounts, you'll need to jack up the front of the truck enough to comfortably get under it, and support the truck with something that CANNOT fail. If the truck falls off the jack, it WILL KILL YOU DEAD. I like to put two or more spare tires/wheels under the vehicle with me - they take the impact if a jack fails, allowing me to survive.

You'll also need to jack up the engine slightly. Not much, just slightly... more to take the weight off the motor mounts than for anything else.

Work ONE motor mount at a time. DO NOT try to do more than one at a time - it's hellish to let an engine float around in there with no motor mounts while you try to get all those bolts to line up again.

After jacking up the engine slightly, unbolt one motor mount from the engine block. You may need any of several different types of wrenches to do this. Also unbolt the same motor mount from the truck frame. Now you can remove the motor mount altogether, letting the engine hang there between the remaining motor mount(s) and the jack. If you hadn't jacked up the engine, now it would have fallen when you took out the motor mount, and it'd have been EXTREMELY difficult to get it back into position so you could reinstall the new mount.

Installation is the reverse of removal. Bolt it (LOOSELY) to the frame, then to the block. You may need to do some prying to get the last bolts to line up with their holes. After all the bolts are installed loosely, THEN you can tighten them all down. If you tighten some before you install the others, the others may be impossible to line up with their holes.

Finish one, move on to the next.

Jul 30, 2014 | Cars & Trucks

1 Answer

How to install a slant 6 225 in a 1972 plymouth duster


Lower engine in bay, loosely attach motor mounts. Install transmission, mate to motor. Install transmission mounts, tighten motor mounts.
Hook up wiring and hoses. Fill all fluids. Reinstall driveline, hook up exhaust and linkage. Reinstall hood. Test work, check timing and carb settings.

Aug 29, 2012 | Plymouth Valiant Cars & Trucks

1 Answer

Video on replacing motor mounts on a 1999 ford escort


I have no video of the job just written instructuions.

  • Park the vehicle on level ground and shut off the engine. Raise the front end of the Escort off the ground using the floor jack. Lower the vehicle onto jack stands placed under the frame to support the car.
  • 2Place the jack under the oil pan and raise the lift plate to the bottom of the oil pan. Remove the engine mount bolt using the 1/2-inch socket wrench. The engine mount bolt is in the center of the mount fitting in clear view.
  • Slowly raise the engine using the jack until the weight of the engine is removed from the engine mount. Pull the engine mount from the fitting and place the new mount in the fitting.
  • 4Lower the engine slowly and insert the bolt into the mounting hole. Tighten the mount bolt to 67.9 foot-pounds using the torque wrench.
  • 5Remove the bolt from the other engine mount the same way as the first one. Pull the mount from the fitting and insert the new one. Replace the bolt to the center of the mount fitting. Lower the engine to the frame and tighten the mount bolt to 67.9 foot-pounds.
  • 6Remove the jack from under the Escort. Raise the car off the jack stands, remove the stands and lower the car to the ground
  • Jul 19, 2012 | 1999 Ford Escort

    2 Answers

    Hi i need to change motor mounts on my 2005 pacifica never dont it before too espensive in the shop can you tell me how dificul it is thsnk you


    you have to lift the engine out of the vehicle far enough to remove bolts this can be a complicated process

    Apr 27, 2011 | 2005 Chrysler Pacifica

    2 Answers

    When I start or drive my 1999 chevy suburban k1500 it make a loud knocking noise in the egine- so loud that can not drive it no where- I was told by a friend that my egine are loose and to be tighten. how...


    if the engine is loose, i would check the motor mounts to see if 1 of them is not broken, if it is , it will have to be replaced, if it is loose, then it can be tightened up. with the appropiate size wrenches. if the knocking sound is coming from the inside of the engine, i would have it checked out soon to see what is causing the knocking. [ interior knocking in a engine is serious. ]

    Feb 16, 2011 | 1999 Chevrolet Suburban

    2 Answers

    Are there any other parts that need to be removed in order to change the front engine mount of a 2005 chrysler pacifica?


    are there any other parts i need to move, in replacing front motor mounts for 2005 pacifica

    Nov 05, 2010 | 2005 Chrysler Pacifica

    2 Answers

    How do I install starter for 2000 GMC Sonoma. This is a 4 cyl 2 wheel drive pick-up


    e
    Removal & Installation
    2-Wheel Drive
    - 2.2L Engine
    1. Remove or disconnect the following:
      Negative battery cable Front exhaust pipe, if necessary for access Starter heat shield, if equipped Brace rod from the front of the engine and the bell housing Drivers side wheel to access the starter motor wires and the starter motor attaching bracket-to-engine bolt through the opening in the wheel well Wires from the starter solenoid Attaching bracket-to-engine mount bolt Starter-to-engine block bolts. When removing the last bolt, be sure to support the starter to keep it from falling and possibly injuring you. Starter and shims (if equipped) from the vehicle Bracket from the starter assembly, if equipped

      e12f2d1.jpg

      Fig. Starter motor and related components - 2.2L engine

    To install:
    1. Install or connect the following:
      Bracket to the starter, if removed. Tighten the bracket nuts to 97 inch lbs. (11 Nm). Starter and shims (if equipped) into position in the vehicle and thread one of the retaining bolts to hold it in position. Bracket-to-engine mount bolt (loosely), if equipped Starter mounting bolt, then tighten all mounting fasteners to 32 ft. lbs. (43 Nm) Wiring to the solenoid Brace rod and tighten the retainers Front exhaust pipe and tighten the fasteners, if removed Starter heat shield, if equipped Driver-s side wheel, if removed Negative battery cable

    Hope helped with this (remember rated this help) Good luck.

    Nov 18, 2009 | 2001 GMC Sonoma Extended Cab

    1 Answer

    Engine motor mounts are broken.


    besure when you replace engine mount.you have to use a engine lift to take weight off the mount.you need a haynes manual.it will show you where engine mounts located.

    May 29, 2009 | 1999 Mercury Villager

    Not finding what you are looking for?
    1999 Mercury Villager Logo

    Related Topics:

    230 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mercury Experts

    yadayada
    yadayada

    Level 3 Expert

    75744 Answers

    fordexpert

    Level 3 Expert

    5495 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    Are you a Mercury Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...