Question about 1994 Ford Mustang

1 Answer

Need to get a programmer dont know where its at

Wipers wont stop need to find programmer 94 mustang

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 4,369 Answers

  • Windshield Wipers Continue to Run When Turn Signal and Windshield Wiper Switch Are Turned OFF
  • Damaged turn signal and windshield wiper switch .
  • Damaged windshield wiper motor .
  • Damaged windshield wiper control module.
need to get a programmer dont know where its at - 7fd52e7.gif
efd7dbe.gif
Pin Number Circuit Circuit Function 1 57 (BK) Wiper Motor Ground (Park) 2 28 (BK/PK) Wiper Module to Wiper Motor (Park Switch) 3 65 (DG) Wiper Motor Power (Park Feed) 4 61 (Y/R) Wiper Motor Common (RUN) 5 56 (DB/O) Wiper Motor LO 6 58 (W) Wiper Motor HI
Windshield Wiper System The windshield wiper system consists of :
  • Windshield wiper motor (17508) (F-type).
  • Washer system.
  • Windshield wiper control module.
  • Turn signal and windshield wiper switch (13K359).
The windshield wiper control module is:
  • Located at the instrument panel fuse panel.
The windshield wiper motor is:
  • Attached to the cowl top extension (021A36) .
  • Connected to windshield wiper mounting arm and pivot shaft (17566) .
The turn signal and windshield wiper switch features a:
  • Rotary wiper switch.
  • Push type washer actuator.
OFF/Low/High Speed
  • Has a two-speed, permanent magnet, three brush electric windshield wiper motor .
  • The windshield wiper motor has a brush rigging that permits selection of low or high speed.
  • When the turn signal and windshield wiper switch is in the LO position, the common brush and the blue/orange wire brush are used, and the windshield wiper motor operates at low speed.
  • When the turn signal and windshield wiper switch is in the HI position, the common brush and the white wire brush are used.
  • In HI position, electric current will bypass a portion of the armature winding causing the windshield wiper motor to operate faster.
  • When the turn signal and windshield wiper switch is moved to the OFF position, the windshield wiper motor will continue at low speed until the park switch outer contacts open.
  • When the park switch contacts open, the windshield wiper motor stops in the park position.
Interval
When the turn signal and windshield wiper switch is in the interval position:
  • The wipers make single wipes separated by pauses.
  • The rotary switch is on the end of turn signal and windshield wiper switch .
  • The length of the pause can be set from approximately 1 to 17 seconds.
  • Length of pause decreases as the rotary switch is rotated away from off.
  • Length of pause increases as the rotary switch is rotated toward off.
While in the interval wiper mode:
  • It is normal to hear a slight click at the beginning of each on/pause cycle. NOTE: When using interval wipers, the first wipe may not occur until after a pause of up to 17 seconds.

Posted on May 27, 2009

  • gerry bissi May 27, 2009





    Section 01-16: Wiper and Washer Systems

    1994 Mustang. Workshop Manual
    REMOVAL AND INSTALLATION



    Windshield Wiper Control Module
    The windshield wiper control module is located at the instrument panel fuse panel.

    Removal and Installation


    1. Disconnect battery ground cable (14301) .


    1. Disconnect harness connector.


    1. Remove windshield wiper control module from bracket.


    1. To install, reverse Removal procedure. Check wiper system operation.

    -----------------------------------

    Removal and Installation


    1. Disconnect the battery (10653) and remove the windshield wiper pivot arms (17526) and windshield wiper blades (17528) .


    1. Remove the cowl vent screen (018A16) by carefully prying up on rear edge of cowl vent screen .


    1. Remove plastic cowl extension from cowl.


    1. Remove clip retaining windshield wiper mounting arm and pivot shaft (17566) to windshield wiper motor link.


    1. Disconnect the linkage drive arm from the windshield wiper motor .


    1. Disconnect the windshield wiper motor electrical connector and remove the windshield wiper motor three retaining screws. Pull the windshield wiper motor from the opening.


    1. To install, reverse Removal procedure. Tighten all motor retaining screws to 13-17 Nm (10-12 lb-ft).


    1. Before installing the windshield wiper pivot arm to the windshield wiper mounting arm and pivot shaft , ensure the windshield wiper motor is in PARK and the windshield wiper blades are set to Dimension X as outlined under Adjustments .

×

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
jaysonemanme
  • 500 Answers

SOURCE: 2003 ford mustang. delay on

needs a wiper motor

Posted on Jun 13, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Wiper motor


Possible wiper linkage has broken/seperated from wiper motor. The wiper cowling covering the linkage assembly will need to be removed to inspect/repair

Feb 13, 2016 | 2008 Chevrolet Impala

1 Answer

What could cause my windshield wipers on 2001 mustang no to work?


Could be many things, but check the fuse's first then turn on the wipers and check for voltage at the motor if you have voltage then its the motor. if you dont its the wiring or switch most of the time its the switch or motor. also some systems have a relay if you know how check that as well.

Jun 12, 2014 | 2001 Ford Mustang

1 Answer

How do i fix nonstop windshield wipers on a 98 ford mustang?


In the instrument panel fuse box , fuse # 2 30 amp. is power for the wiper control module . Pulling that fuse will or should turn them off . Your wiper / washers are controlled by a electronic control module , if i were to guess ,i would say that was bad. But that is just a guess , without testing don't know for sure . Also there is a switch inside the wiper motor that allows parking operations of the wipers .

Oct 01, 2017 | 1998 Ford Mustang

1 Answer

Power seat wont work 1996 mustang convertible


http://www.moddedmustangs.com/forums/94-95/64750-how-fix-my-power-seat.html
please find this site useful sounds to me that wire use to belong to your power seat motor but they recalled the motors because they had a tenancy to catch fire and burn the seat

Sep 27, 2012 | 1996 Ford Mustang

1 Answer

My speedometer wont work nor trip gage on 94 MUSTANG


it sounds like the speedometer cable is unhooked.

Apr 04, 2010 | 1994 Ford Mustang

1 Answer

Washer fluid leak in lines


Run your own new line through the engine compartment from the wipers to the washer bottle and leave the old disconnected leaky line right where it is.....out of sight.

Aug 13, 2009 | 1994 Ford Mustang

2 Answers

Where to find fuse diagram for 95 Ford Mustang?


http://www.allfordmustangs.com/forums/attachments/94-95-tech/608d1036338026-need-fuse-box-diagram-95-gt-esb01113.gif


hope that helps.

Mar 26, 2009 | 1995 Ford Mustang

Not finding what you are looking for?
1994 Ford Mustang Logo

Related Topics:

2,143 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77201 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

fordexpert

Level 3 Expert

5579 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...