Question about 2005 Chrysler Pacifica

1 Answer

Replacing 2005 pacifica flywheel

Can the flywheel be replaced without removing the engine?

Posted by on

  • Richard Scordino May 11, 2010

    Yes...but then, you need to remove the transmission.

  • Jennifer Martin
    Jennifer Martin Apr 07, 2018

    How to do I flywheel on a 2006 Chrysler Pacifica

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

Not on front wheel drive unless your hands are no bigger than an infants hands

Posted on May 27, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing the crankshaft in a 2005 mitsubishi galant 2.4l. Can you take the crankshaft out without removing the engine?


Sorry, the engine will need to be removed to replace the crank. The flywheel goes into the bell housing on the rear of engine which will need to be removed.

May 13, 2018 | Mitsubishi Cars & Trucks

2 Answers

Flywheel replacing


you will need a replica flywheel and new bolts plus torque range and manfacturers specs.

Nov 07, 2016 | Cars & Trucks

1 Answer

Have a 2005 Pacifica that will not go above 2500 rpm without stalling. Replaced fuel pump, still have the same problem ??


Do you have an engine light on? It sound like it is in limp mode which limits rpm and speed

Nov 08, 2014 | 2005 Chrysler Pacifica

1 Answer

I need to know how to replace the egr valve on a Pacifica 3.8L


Replaced the one on my 2005 Pacifica, 3.8L. There's not easy way to replace it unless you remove the intake, which is additional work. When I did the work, I didn't take the intake off and basically had to lay on top of the engine and reach with both hands around. If you have a few extra bucks, it's worth the time and hassle to pay someone else to do it.

Sep 12, 2011 | 2005 Chrysler Pacifica

1 Answer

It Started about 6 months ago on my 2005 chrysler Pacifica v6 3.8. my upper radiator hose colapses when i rev the engine up and it gets really hot. i can tell by the smell. i have replaced my thermostat...


REPLACE UPPER RADIATOR HOSE IT IS TOO SOFT WORN OUT CAUSE HOSE TO CLASP.I WOULD REMOVE THERMOSTAT FLUSH ENGINE BLOCK AND RADIATOR COOLANT SYSTEM NEED FLUSHING OUT.

Dec 14, 2010 | 2005 Chrysler Pacifica

1 Answer

My 2005 golf 5 gti dsg currently has 89000km on the clock. It is used extensively in traffic covering 60km/day/week. It has developed an irritating "knocking noise" in the engine.Booked it at a local VW...


hi,
i couldn't say for certain without hearing the noise , but i have replaced one or two "dual mass flywheels" on these models, alot of people don't realise the dsg actually has a dual mass flywheel.
regards
P

Aug 03, 2010 | 2008 Volkswagen Gti

1 Answer

Location of pcm on 2005 pacifica?


I have a 2004 Pacifica and mine is on the drivers side front, underneath between the bumper and the wheel splash guard. You will need to remove the splash guard ti access the PCM. Not very hard at all. Replacement time for a handy DIYer: about 1/2 hour. Good luck!!

May 12, 2010 | 2005 Chrysler Pacifica

1 Answer

I have a 2005 Pacifica 3.5. I want to replace my car starter. Where is it located?


It's in the front. Remove the cover over the radiator then the coolant line bracket remove the bolt from the front engine mount support engine remove bolt on trans and anything else that would be in the way remove starter. Time for a shop to do this is two hours so give yourself a day

Jan 07, 2010 | 2005 Chrysler Pacifica

Not finding what you are looking for?
2005 Chrysler Pacifica Logo

Related Topics:

467 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

80407 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...