Question about 1997 Ford Crown Victoria

1 Answer

Stereo removal I have a 1997 Ford Crown Victoria and was wondering if I needed to remove the entire dashboard to remove the tape deck?

Posted by on

  • yadayada
    yadayada May 11, 2010

    no they just slide out using a special radio spring clip release tool set.

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 50 Answers

If you have unit i think you have look for 2 holes 1/8 inch in dia on both sides take a coat hanger and cut 2 12 inch lengths and bend into semi circles and insert into holes firmly and it will slide out if not have a friend pull on the radio while you push on your new ford radio tools

Posted on May 28, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi, How do I replace the tail light bulbs in my '97 Crown Victoria? Thanks


Sedans
  1. Remove the screw(s) and wing nut retainers at the rear of the luggage compartment and push the trim away from the back of the light.
  2. Remove the wing nuts retaining the light assembly to the vehicle and the retaining nut from either side of the luggage compartment and pull the light body assembly from the vehicle.
  3. Turn the bulb socket(s) counterclockwise to the stop and remove the socket(s) from the light assembly. Remove the bulb(s) from the socket(s).
  4. Installation is the reverse of the removal procedure.
56c16fa.gif
Push the trim away from the back of the light—1992-98 Crown Victoria

f147c29.gif
The rear tailamp assembly is held by various fasteners

da5bd90.gif
Remove the wing nuts retaining the light assembly to the lower back panel—1992-98 Crown Victoria

e896b59.gif
Remove the nut retaining the light assembly from the side of the luggage compartment

2e1520f.gif
Pull the light assembly away from the vehicle—1992-98 Crown Victoria

Oct 12, 2009 | 1997 Ford Crown Victoria

1 Answer

Reaching rear seat belt on 1997 crown victoria


Lap belt or shoulder harness? Lap belt - remove rear seat bottom by pushing in on bottom edge of the seat cushion and lifting. This will expose the lap belt and its anchor. Shoulder belt should be accessible via trunk compartment. If not then you'll have to remove the back of the rear seat to get to it.

Oct 04, 2009 | 1997 Ford Crown Victoria

1 Answer

I need to get my 97' Crown victoria trunk open from the inside.


There should be a safety trunk release located on the upper rear window deck platform- a black handpull . If it is still intact- it should pop the trunk lid.

May 27, 2009 | 1997 Ford Crown Victoria

1 Answer

1999 crown victoria


You don't.
The dash has to come out in order to remove the HVAC box to get to it.

Apr 29, 2009 | 1999 Ford Crown Victoria

2 Answers

How do you remove the lens cover for the left front turn signal on a 1997 Ford Crown Victoria?


must remove the assembly from the car, unbolts from the inside of the engine compartment.

Apr 21, 2009 | 1997 Ford Crown Victoria

2 Answers

Removal of lower ball joint


yes it is safer to use a bal joint press . and it goes downward.

Apr 17, 2009 | 1997 Ford Crown Victoria

1 Answer

Remove heater core 1998 crown victoria


You dont need to remove all of those thing to do that. Working on the passenger side, remove the globe box and then the air bag, you are gonna see the bolts there. Now yo can see the black box behind the globe box? you have to remove the screws, some from the inside and some from the ouside (very hard to reach, under the box of the AC box outside).
Lifth the black box of the heater core and change it!!!

Mar 31, 2009 | 1998 Ford Crown Victoria

1 Answer

I would like to know how many bolts hold the front fenders on to a 1997 ford crown victoria and their locations


no more then 10 to 15 bolts they are under the hood remove the inner fender and you will see the rest and there should be one or two under the car near the doors

Mar 20, 2009 | 1997 Ford Crown Victoria

1 Answer

How do I change the headlight in 1997 crown victoria


Remove the set screws from the housing and remove the light.

Nov 26, 2008 | 1997 Ford Crown Victoria

Not finding what you are looking for?
1997 Ford Crown Victoria Logo

Related Topics:

196 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...