Question about 2000 Chevrolet S-10

1 Answer

I have a disconnected vacuum line. it is located at the T by the hinge on the driver side. it is a short line no longer than 8 inches and comes out of the right side of the T. where does this line belong? and could it be the reason my 4x4 is not working? I have the same loose line, same non-functioning 4WD (and it's stuck where it is until I fix it). Where the ***$%*@# does it connect? I can't find anywhere to connect it, not a vacuum hose routing picture.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,118 Answers

You might want to chk. to see if it hooks to your diafram that locks in your front axels, or to a port around the back of the plentem, you should hear it whisel when the truck is ideling. I would almost bet it goes to that diafram.

Posted on May 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i connect/disconnect electric from drivers side sun visor?


you should be able to remove two/three screws that hold hinge on visor and slowly pull out wire , there should be a connector on there a few inches in you can undo

Jan 09, 2015 | 2006 Dodge Ram 2500

1 Answer

What side is pcv for a 1994 dodge 318


Switch the valve covers to the correct side

The oil fill cap should be on back drivers side
& pcv on passenger side in middle as I recall

Mar 04, 2013 | 1994 Dodge Ram

1 Answer

Hay i have a 1991 subaru gt legacy.the car starts fine but runs a lil ruff,but its wen u give it a little throttle it runs more rrough and then u gve it more and then its alryt.the coil packs r fine and i...


Could be a few things, if you pull the plug wires off the coil and there a little bit corroded and light green in color I would replace your coil. The easiest check is to check and see if the EGR valve and vacuum solenoid are working properly. Locate the EGR valve, It's about 6 to 8 inches from the throttle body towards the drivers side. It looks like a small stepped flying saucer about 3 inches in diameter with a vacuum line going to it. Get something like a golf "T" to fit into and plug the vacuum line once you have disconnected it. Drive the car to see if there is any improvement in driveability. If not, then there are more things to look at but those are the most common. I hope this info helps.

Jul 28, 2011 | 1991 Subaru Legacy

1 Answer

I Have a LT1 motor in my car. There are a"old" and


The old style fits into the timing cover that has the small hole for the actual distributor shaft. The old style also has no vacuum lines connected to it, or no provisions for vacuum lines to be connected to it.

The newer style has one vacuum line that runs from the elbow that connects the throttle body to the MAF, and another vacuum line that goes to the drivers side of the intake manifold. The timing cover has a hole about 2 inches in diameter for the newer Opti, the old version has a hole about 3/8" in diameter. If the distributor is installed look for the vacuum lines on the opti. The one that goes from the intake elbow attaches to the drivers side front in about the 2, O clock position. The one that attaches to the intake manifold attaches to the drivers side too, at about the 5, O clock position.

Dec 09, 2010 | 1995 Chevrolet Camaro

1 Answer

Engine light on.engine read out say's it's a vacuum leak.replaced the gas cap engine light still on. what could be the cause?


Well, it is most likely a vacuum leak *somewhere*. Open the hood, look around carefully for any cracked, broken, or disconnected vacuum lines (these are usually about 1/4 inch in diameter, black rubber hoses, sometimes 1/8 inch diameter rigid black plastic tubing). Often one or more goes to the firewall to control the a/c dampers, make sure that the air comes out of the defrost vents, the dash vents, and the floor vents according to the knob settings, if not, look for the engine to dash hose.

Sep 01, 2010 | 2001 Jeep Grand Cherokee

2 Answers

I have a 2004 Jeep Grand Cherokee. The operation of the manual Climate control no longer allows me to select which vent I want air, center, floor, and defrost. I only get air out of the defrost vents.


This system uses vacuum from the engine intake manifold to steer the vacuum actuator of the mode door. Fail safe position is defrost. Most of the time problem is caused by a loose vacuum line at the manifold or a shaved trough line somewhere under the hood. The line runs on the LH side off the engine (as seen from drivers position) starting on the intake manifold.

May 20, 2010 | 2004 Jeep Grand Cherokee

1 Answer

Heat only comes out of defrost


Most of the time when that happens you have lost the vacuum to the heater. Look under the hood near the fire wall for a broken or disconnected vacuum line. They are usually plastic and about 1/8 inch in diameter.

Dec 13, 2009 | 1993 Dodge Spirit

1 Answer

I have a disconnected vacuum line. it is located at the T by the hinge on the driver side. it is a short line no longer than 8 inches and comes out of the right side of the T. where does this line belong?...


Yes it could be why your 4x4 is not working. The 4x4 on some GM vehicles works off of vacume. Also there is a shift module or switch whatever you whant to call it on the front axle and these are notorious for going bad. You can buy a manual cable set up on ebay for around $100 this will eliminate the 4X4 not engaging.

Apr 28, 2009 | 2000 Chevrolet S-10

1 Answer

Power steering and brake line location2002 Chevy Silverado 2500HD


the power steering lines are very short hoses approximately 8 inches long that go from the power steering pump down to the steering box, which is located on the frame, just below the pump. The brake lines run from the master cylinder(where you fill it with fluid on the drivers side firewall) down to the frame, and then follow the frame both directions; both to the front end and the rear end, along the drivers side frame rail, just on the inside of it. The fuel line runs along the same path to the rear.

Mar 03, 2009 | 2002 Chevrolet Silverado 2500HD

Not finding what you are looking for?
2000 Chevrolet S-10 Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...