Question about 2001 Dodge Dakota

1 Answer

Fan switch works on only one speed

2001 Dodge Dakota. How do I remove and replace?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Dodge Master
  • 358 Answers

  1. Disconnect and isolate the battery negative cable.
  2. From the passenger foot well area, remove the two hex screws used to secure the blower motor resistor.
  3. Unplug the front blower motor resistor from the wire harness connector.
  4. Pull the front blower motor resistor and its wire harness out of the plenum panel and through the cowl plenum access hole far enough to access the wire harness connector.
  5. Remove the front blower motor resistor from the cowl plenum.
INSTALLATION
  1. Plug the blower motor resistor into the wire harness connector.
  2. Install the blower motor resistor to the cowl plenum panel by feeding the resistor and wire harness back through the cowl plenum access hole.
  3. Install and tighten the two screws that secure the resistor to the HVAC unit Tighten the screws to 2.2 Nm (20 in. lbs.) .
  4. Connect the battery negative cable

Posted on May 27, 2009

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I need to replace the blower motor harness in a 2001 dodge dakota


you can buy that pigtail and solder it back in there. use shrink tubing also. replace the resistor

Sep 22, 2017 | 2001 Dodge Dakota

1 Answer

2001 DODGE DAKOTA A/C FAN NOT WORKING.I REPLACED FUSE AND RESISTOR WITH NO LUCK. HELP


First you have to figure out if you are missing power to the blower motor, or ground to the motor. The motor gets power from the key switch, and the fan switch grounds the resistor to change speed.

Jun 02, 2013 | Cars & Trucks

2 Answers

Heat / air cond control fan works only on high where is the problem


your control switch ,where you turn on up to high position, is bad. replace it

May 14, 2011 | 2001 Dodge Dakota

1 Answer

Heater fan not working on 2001 Dodge Dakota.. Fuses are good.


Wire between fan motor & switch disconnected or fan motor bad. Check and/or replace

Feb 11, 2011 | 2001 Dodge Dakota

1 Answer

2001 dodge dakota how do I relace the cabin fan


the blower motor resistor if i remember correctly is behind the glove box ,once u remove the glove box u should see it . make sure u check the wiring connector, i have ran into a few that has melted ..had to ret a replacement from chrysler that had a bigger supply wire. hope that helped you!!!

Jul 08, 2009 | 1998 Dodge Dakota

1 Answer

Fan on heat and/or a/c won't work unless on high


Your fan speed dropping resistor is burnt out, it is located near the blower motor.

Apr 27, 2009 | 2001 Dodge Dakota

2 Answers

Heater fan only works on the two low settings.


if you have checked the switch as recommended, it is most likely to be the heater resistor which contols the diffrerent speeds. it is
normally fited near to the motor and is a squarish block with multiplug on it and coils like springs in the centre of it, look at the coils they may be burnt out.hope this helps

Apr 22, 2009 | 2001 Dodge Dakota

1 Answer

Fan control knob has only two speeds, ''Off'' and ''high.'' Can knob be replaced or do I need replace complete control unit.


there is no computer control unit, what u need to replace is the fan speed control resistor module.

Mar 22, 2009 | 2001 Dodge Dakota

Not finding what you are looking for?
2001 Dodge Dakota Logo

778 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...