Question about 1995 Chevrolet Lumina

Open Question

Replacing a High Pressure Power steering hose on 95 chevy lumina

We are trying to replace the high pressure hose on a 95 chevy lumina but on one end we can't get the bolt off. We need to know how to get in there and what tools we will need.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

c17hydro
  • 2984 Answers

SOURCE: high pressure power steering hose leak 97 chevy 4x4

Very simple and no special tools. Take your time and put some rags or a oil pan underneath it and wrench away!

Please don't forget to rate!!!!

Posted on Mar 14, 2009

  • 1596 Answers

SOURCE: high pressure power steering hose on a 1995 surburban

PUMP R&R PROCEDURE at Bottom


Do I need to pull the power steering pump off of the 1995 surbuban 350 engine in order to replace the high pressure hose?<-You Ask.

NO Not on the 95 and If you do need or want to REMOVE the PUMP it Comes off Without the Removal of P/S Pump Pulley. Now if you are replacing the P/S Unit Yhere is A Special tool fo pull off Pulley .
Ist a Universal tool for Ford & GM just P/S Pump Pulley Removal Tool Auto Zone has en for $40.00 or rent it from them.

POWRE STEERING PUMP R&R

Removal/Installation Notes

  1. Disconnect hoses at power steering pump, then plug pump ports and hoses to prevent dirt entry.
  2. Loosen pump adjusting bolt and remove pump drive belt.
  3. Remove pump to support bracket retaining bolts, then the pump.
  4. Reverse procedure to install.

Posted on Mar 22, 2009

michigan man
  • 3533 Answers

SOURCE: Power Steering Pressure hose, 1976 Cadillac Eldorado

yes you can repair it and you are right about the flang try this website to see if they have your car listed www.autozone.com to get pictures and diagram i also would like to give you this information website www.schramauto.com if you ever have any hard to find GM-parts Schram auto & truck parts sells only GM-parts and i hope i have been some help to you and you have a nice car.

Posted on Apr 25, 2009

thunderalley
  • 432 Answers

SOURCE: I'm replacing the Power Steering Pressure Hose on my 1995 Chevy

buy a new hose assembly and get some line wrenches the lines are very tight.when you remove the old hose it will spill some hyd. oil.catch it in something. install the hose and fill to the just above the add line.

Posted on Sep 13, 2009

  • 2 Answers

SOURCE: How to replace high pressure hose on steering,

Found a diagram online myself..

Posted on Nov 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Power steering hose keeps breaking, even when replaced by high pressure hoses. Replacing rack and pinion does not help either.


A bad seal in the rack and pinion would have caused low pressure from fluid by-passing the seal. This also would have caused noticeably increased effort to steer the vehicle. Excessively high pressure would indicate an issue between the power steering pump and the rack, and since the hoses have been replaced I would focus on the pump. PS, find a real mechanic, not a parts changer.

Apr 06, 2014 | 2001 Chrysler Town & Country

1 Answer

Power steering hose diagram


power steering hoses run from pump to the steering box, (high pressure) and from the steering box to pump (low side).. is a closed connection. pump to box, then from box back to pump. High pressure should have pressed on fittings, while low side may have normal water hose clamps or replaceable hose without pressed on fittings.

Dec 16, 2013 | Cars & Trucks

1 Answer

How to change powerstering pump chevy uplander


I just finished replacing mine.

It is much easier if you do these steps:

1. Remove the serpentine belt.
2. Remove the nuts holding the main fuse box over the battery.
3. Remove the reinforcing bar over the battery.
4. Remove the battery.
5. Remove the windsheild washer tank.
6. Now you have access to remove the pump pulley. Without removing the stuff, it may be possible, but it will be extremely difficult.
7. Remove the pump pulley.
8. Loosen the high pressure hose fitting.
9. Remove the return line clamp.
10. Remove the power steering pump mounting bolts.
11. Remove the high pressure hose fitting.
12. Remove the power steering pump while sliding off the low pressure hose.
13. Remove the clips holding the reservoir on the pump.
14. Remove the reservoir.
15. Install new o-ring on the reservoir.
16. Install reservoir on new pump.
17. Install clips to hold reservoir on pump.
18. Install new o-ring on high pressure fitting.
19. Place new pump in position while sliding on low pressure hose.
20. Loosely attache high pressure fitting.
21. Tighten pump to mounts.
22. Tighten high pressure fitting.
23. Install clamp on low pressure hose.
24. Install power steering pulley.
25. Install washer reservoir.
26. Install battery.
27. Install reinforcing cross member.
28. Install fuse panel.
29. Install serpentine belt.
30. Bleed the power steering system.

Dec 13, 2012 | 2008 Chevrolet Uplander

2 Answers

Replace power steering pump on 06 chevy uplander


I just finished replacing mine.

It is much easier if you do these steps:

1. Remove the serpentine belt.
2. Remove the nuts holding the main fuse box over the battery.
3. Remove the reinforcing bar over the battery.
4. Remove the battery.
5. Remove the windsheild washer tank.
6. Now you have access to remove the pump pulley. Without removing the stuff, it may be possible, but it will be extremely difficult.
7. Remove the pump pulley.
8. Loosen the high pressure hose fitting.
9. Remove the return line clamp.
10. Remove the power steering pump mounting bolts.
11. Remove the high pressure hose fitting.
12. Remove the power steering pump while sliding off the low pressure hose.
13. Remove the clips holding the reservoir on the pump.
14. Remove the reservoir.
15. Install new o-ring on the reservoir.
16. Install reservoir on new pump.
17. Install clips to hold reservoir on pump.
18. Install new o-ring on high pressure fitting.
19. Place new pump in position while sliding on low pressure hose.
20. Loosely attache high pressure fitting.
21. Tighten pump to mounts.
22. Tighten high pressure fitting.
23. Install clamp on low pressure hose.
24. Install power steering pulley.
25. Install washer reservoir.
26. Install battery.
27. Install reinforcing cross member.
28. Install fuse panel.
29. Install serpentine belt.
30. Bleed the power steering system.

Jul 08, 2012 | 2006 Chevrolet Uplander

1 Answer

How to change power steering hose on chevy k1500 1989?


there r two hoses for high pressure hose u will need either a 5/8 & or a 19mm flare hut wrench (tubing hose wrench)for low pressure hose use side cutter pliers to cut two clamps off at either end of hose, will need new low pressure hose and two clamps. don't forget to re-fill with proper p/s fluid

Jan 15, 2011 | 1989 Chevrolet K1500

1 Answer

Power steering fluid leaking pretty good on 2005 chevy impala. not from pressure line ithink. any clues


The power steering pump is belt driven. It is on the engine where you put fluid in. There are two lines that run from the power steering pump to the power steering rack on the firewall. The fluid can leak from the pump, either of the lines or the rack itself. If you are handy you may be able to repair the problem by replacing the bad part. Wear safety glasses when looking for the leak and do not touch the fluid leak when the engine is running. The pressure is high enough to hurt you. If you ignore the problem you will eventually loose the power assist and may be unable to steer the car. Fix it now!








One line is high pressure and the other is a return line. Check them with the engine off and when you think you've found the leak staret the car and look for the leak. If it sprays like a water hose DO NOT TOUCH THE LEAK. The pressure is high enough to cause serious injury.

Mar 19, 2010 | 2005 Chevrolet Impala

1 Answer

Subaru impreza 1993 power steering leak


YOU CANT USE A REGULAR FUEL LINE ON POWER STEERING AS A HIGH PRESSURE HOSE.BECAUSE POWER STEERING PRESSURE IS 1000 PSI.YOU HAVE TO BUY THE POWER STEERING HIGH PRESSURE HOSE IT HAS NUMBER OF PLIES MATERIAL WEAVES TO MAKE IT STRONG.IT WAS MADE FOR POWER STEERING HIGH PRESSURE.YOU DONT HAVE A BLOCKAGE .THE HIGH PRESSURE HOSE JUST WORE OUT.REPLACE IT .IT SHOULD FIX THE PROBLEM.

Sep 04, 2009 | 1993 Subaru Impreza

Not finding what you are looking for?
1995 Chevrolet Lumina Logo

Related Topics:

1,331 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...