Question about 1993 GMC Jimmy

1 Answer

Out put shaft came out of my output tube

My output shaft came out of the out put tube on my 4x4 gmc jimmy 1993 i put it back in with a long bar it stayed in will it be ok what holds it from coming out

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • GMC Master
  • 6,982 Answers

It shouldn't come out, and you shouldn't have been able to put it back in. Check whatever is allowing so much movement that the two parts can separate. Change whatever it is (likely bushing or mount somewhere) If you have a lift kit in there it can change geometry...you may also have a problem there.

Posted on May 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do you pull a 1979 gmc jimmy 4x4 rear right axle


QU40221 19 Spline Outer Axle Shaft for 1977 to 1991 Chevy, GMC Corporate GM 10 Bolt Front Axle is a genuine original equipment outer axle stub shaft for all GM 10 Bolt front axles in 1977 to 1991 Chevy Blazers, GMC Jimmys, and Suburbans, plus Chevy, GMC 4x4 1/2 ton and 3/4 ton Pickups. The splined end on these new axle shafts has three snap ring grooves in three places so they are compatible with all types of automatic and manual lockout hubs plus all full-time solid splined drive gears.

Also available while supplies last: QU40221U Used Outer Axle Shaft with 3 snap ring grooves and QU40660UUsed Inner Axle Shafts with 2 snap ring grooves (QU40660U is not compatible with automatic locking hubs)



see this vdio

Apr 01, 2015 | GMC Jimmy Cars & Trucks

1 Answer

4x4 wont work


Sorry would need a play and a drive so ask a local mechanic to have a look for you ,could be simple or a complicated thing like a drive shaft broke

Feb 17, 2014 | 2000 GMC Jimmy

2 Answers

Where is the speed sensor located on a 93 jimmy 4.3 4x4 and is there any sensor on ****** that would be involved or cables?


The vehicle speed sensor(VSS)is located on left rear of transfer case on 4x4( 4wd) 1993 jimmy.Ensure ignition is off.Raise and support vehicle .Disconnect VSS electrical connector.Place a container under VSS mounting area, to catch transmission fluid when VSS is removed.---- On 4wd the VSS is threaded,un-thread VSS from transfer case.Then remove VSS and O-ring.Installation in reverse.--------- This will help.Thanks.Helpmech.

Aug 05, 2011 | GMC Jimmy Cars & Trucks

1 Answer

Can you tow a 1999 jimmy behind a rv?


U should remove the rear shaft when towing if it is 4x4 you can put the transfer case in neutral without pulling the shaft.

Jul 25, 2010 | 1999 GMC Jimmy

1 Answer

Location o il filter 1993 gmc jimmey


if its a 4.3 v6 4x4
its behind the airbox on the drivers side fender (relocator kit factory)

Mar 25, 2010 | 1993 GMC Jimmy

1 Answer

Have a 1993 Jimmy and having problems pulling the starter out to replace it. 4x4 The lines running from the transmission to the radiator and the drive shaft seem to be in the way of getting it out...


the lines are steel and will flex without breaking, just dot kink them. You might even have to remove a clip that holds them in place so you can get the starter out, do not forget to reinstall the clip after you put the starter back in.

Mar 10, 2010 | 1993 GMC Jimmy

1 Answer

Need to know where the vacuum lines for the 4l60e tranmission go in a 93 S15 gmc Jimmy


94 chev truck 4x4 350 put new injectors in now it idles to fast what to do (trottle body)

Feb 07, 2010 | 1993 GMC Jimmy

2 Answers

Rough idle and alot of carbon out exhaust pipe, 1993 gmc jimmy


You need new egr valve gasket with a screen on it. It will block carbon from clogging it causing rough idle. Need 10mm wrech and socket set. I found the part at napa for around 22 bucks. I have had my 93 4x4 Jimmy for 10 yrs it now has 235000 on it and still going.

Dec 30, 2009 | 1993 GMC Jimmy

1 Answer

Output shaft separated from output tube 93 Jimmy


You need to disassemble the front diff as there is a clip that holds the shaft in the housing. You should just be able to remove the housing if it is the right side, whole diff for the left side.

Jul 14, 2009 | 1993 GMC Jimmy

1 Answer

Like a tire rubing noise in right front on 97 gmc jimmy 4x4


If noise will go away when you turn wheels a different dirrection you need a wheel brg. hub assem.

Jan 01, 2009 | 1999 GMC Jimmy

Not finding what you are looking for?
1993 GMC Jimmy Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...