Question about 1990 Isuzu Trooper

2 Answers

"90" Trooper will not go in gear when eng running

Had Clutch, master & slave cly replaced but will not go in gear when eng running. "90" Trooper. tech talking about air bubbles in sys. still Will NOT shift with pedal in. Can someone help.. Rocker_jet@yahoo.com Thanks... Oh I am into it so far 1G.

Posted by on

  • rocker_jet May 27, 2009

    Tryed this and still after hours of wait time . Once I start eng. and push pedal. WILL NOT GO IN GEAR. now tech talking about rebuilding tranny. Sinkros? reverse is non sinkro gear but still will not shift into reverse. having master ansd slave replaced again. is it possible bad parts? Friend telling me clutch plate could b installed backwards... could it be a pedal problem? linkage set all the way out... can start with pedal pushed and in gear. and vehicle wants to go, Reverse and 1st gear.. is it a seating issue with the clutch plate? once I take out of gear, can not put back into gear without shutting eng. off.. HELP

  • rocker_jet May 30, 2009

    Thank you for your Help. After 2 Slaves and 3 Masters I got good parts, Back on the Road again... Thank everyone for your help with this matter...

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Isuzu Master
  • 2,007 Answers

You'll have to bleed your system. There should be a bleeder screw on your slave cyllinder.Stick a piece of vacuum hose on it, and have the other end of the hose in a bottle of brake fluid. Keep pumping your clutch until no more bubbles come out of the hose, and then, with the clutch held in, tighten your bleeder screw again, and you should be good.

Posted on May 27, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

It could be possible you have bad parts. I have had several new parts bad, and the shop charged me every time i swapped them out. Hopefully the shop your working with is willing to swap parts out again, with out being charged for labor. Air bubbles can also be a nightmare when working with hydrolic systems.

Posted on May 27, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I replaced the master cylinder for my 91 s10 now the clutch won't spring back how do I fix this


What master CLY did you replace clutch or brakes you have air in the slave CLY for the clutch system and you will have to bleed the system and make sure you don't run low on brake fluid while you are bleeding the system.

Apr 11, 2016 | Cars & Trucks

1 Answer

My 90 ford probe lx will not drive unless i start it in second gear and will not shift in any gears when clutch is applied. Clutch master replaced and clutch. What else can be the problem???


See if your slave cylinder needs bleeding. Follow the line from the master cylinder down to the bell housing to find the slave. When clutch pedal is pressed, a rod on the slave should move outward just a little. It will move the clutch fork to engage the clutch.

Feb 17, 2016 | Ford Cars & Trucks

2 Answers

Why is my chevy s10 gears are getting harder to put in ?


I would look to see if the clutch master cylinder is low. It is smaller but like the brake master cylinder. If so check to see if the slave cylinder on the bell housing is leaking or the master cylinder is leaking. Low fluid or no adjustment will make it hard to get in gear.

Aug 07, 2014 | 1999 Chevrolet S-10 Pickup

1 Answer

How would i find where my 1996 Isuzu Trooper is leaking clutch fluid?


clutch fuild leaks due to bad slave, bad mc or lines

Jul 16, 2014 | 1996 Isuzu Trooper

1 Answer

1986 isuzu trooper clutch pedal went soft


some of these were manual clutch cable check adjustment of cable at firewall (bulkhead) and check for cracks around where cable goes through to inside cab common on old girls.
if hydraulic clutch system
check fluid in clutch master cylinder is it low?
it could have leaking slave cylinder on gear box bell housing or your clutch needs replacing, gear box out and replace clutch as a kit, pressure plate, clutch plate, thrust bearing (comes as kit) but dont forget to check and or replace the spigot bearing in the rear of the crank shaft when doing clutch kit.

Apr 01, 2014 | 1986 Isuzu Trooper

1 Answer

I had a new clutch asembly and new slave cly put in my 1990 nissan truck about year and half ago. My problem is my clutch is hard to push down and if i don't push it all the way to floor it will g


replace the clutch master cylinder. The rubbers on the piston swell over time and/ or break down blocking up the ports in the cylinder.. Wrong fluid is the main culprit for this type of fault.

Mar 29, 2013 | Cars & Trucks

1 Answer

Replaced clutch master which was leaking. 3mos


no, the clutch disk is just worn out.

May 18, 2010 | 1994 Isuzu Trooper

1 Answer

1994 Altima clutch master and slave replacement


easy replace both parts then fill the clutch reservoir,crack slave cly bleeder to let gravity bleed let 1 to 2 reservoirs flow through,tighten bleeder and pump clutch pedal,pump 4 or 5 times hold down pedal get 2nd person to crack bleeder while pedal is down,tighten bleeder before releasing pedal,should work fine

Nov 04, 2009 | 1994 Nissan Altima

1 Answer

My 1989 chevy beretta will not go in gears i have fluid it was going in drive but now it locked in a gear and would not go.


I actually have the same issue with my '90 Beretta. I have not yet had the time to look at it but I could suggest that either your master or slave clutch cylinder is shot or your clutch linkage needs to be tuned/replaced. A Master clutch will run about $50.00 at your Autozone or Advanced Auto, and the slave is about $40.00. I'm not sure wht the linkage will run you, nor do I know the cost of repair if you decide to have a mechanic fix it for you.

Aug 20, 2008 | 1989 Chevrolet Beretta

1 Answer

1992 blazer clutch


These systems are a pain to get the air out of. Have an assistang push in on the pedal and push back on the slave cyl. and crack bleeder valve at the same time. Step on the clutch pedal slowly when doing this.

Jun 10, 2008 | 1992 Chevrolet S-10 Blazer

Not finding what you are looking for?
1990 Isuzu Trooper Logo

158 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14384 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...