Question about 1999 Ford Taurus

2 Answers

Inner tie rod end on passenger side needs replaced

I need to replace inner tie rod end on my 99 ford taurus how hard of a job is it? please help

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 74 Answers

Its not that hard its just a pain getting access to it as you will find the unit is tight and there is not a lot of room for leverage.

regards JR

Posted on May 27, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,004 Answers

You will definately need an expert to handle this because it is in a tight compartment.

Good luck.

Posted on May 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 FORD TAURUS INNER TIE ROD END


They screw on & then are cripped with a special tool

Dec 24, 2012 | 2002 Ford Taurus

1 Answer

Both inner tie rods r bad on my 2002 ford taurus.. i would like to try and replace them myself and save a few bucks.... i'm not too mechanically inclined, any help would be appreciated


The inner tie rod end is attached to the steering "rack". It doesn't take any "special" tools but since the steering rack is attached at the rear of the engine compartment, it is extremely awkward to do. I would recommend this job be taken to a shop that you trust. It is not that hard to mess up the steering rack with the wrong tools and then you have to replace the whole steering rack.

Jun 28, 2011 | Ford Taurus Cars & Trucks

2 Answers

Need to replace inner tie rod on a 1998 ford ranger two wheel drive , driver side . engine size is 2.5. do i have to take outer tie rod off as well?


webbraymond2, Yes, you have to remove the outer tie to access the inner tie rod. When you do this, count the rotations of the tie rod as this will have to be replaced when the new inner tie rod is installed. Counting the rotations will allow you to put the outer tie rod close to where it was when you started the job. You are changing the toe setting when you have to replace either the inner or outer tie rod. You need to access and remove the jamb nut and boot before you can access the inner tie rod and this is why the outer needs to be removed first. A wheel alignment is advised after you finish the job. Good luck with this.

May 28, 2011 | Ford Ranger Cars & Trucks

1 Answer

I have loose tie rod ends on both the right and left side of a ford 1999 expedition. On the passenger side the bottom bolt is missing completely. Do I need to replae both with a whole new assembly?


If the tie rods are just loose,you replace the bolts

Obviously if the end joint or brg is worn & loose you replace
them. (not the entire arm,just the joint)

You can replace the bolt or the tie rods yourself,
then have the front aligned within a few days as the
toe will be off.

I assume your talking outer ties rod ends,
not inner --- inside the steering rack boots!!

The inner joint does require the complete, what
looks like a rod or arm to be replaced

Apr 26, 2011 | 1999 Ford Expedition

1 Answer

How hard is it to replace the right side tie rod end?


Hello arriedad: My name is Roger and I will help with your question. It would depend on which tie rod end you are replacing.There are two right tie rod ends. You have a inner and a outer tie rod. The outer tie rod is easy. The inner takes a special tool to replace it. You will need an alignment when you are done as you will not be able to see when you have it correct. You can try to count the threads but the new end might be cut different. I would suggest that if you are not sure have a front end person perform the repairs. This way the alignment can be set at the same time. If not set you have premature tire failure. Some repairs are just best left to an expert if not for you then the safety of your family. If you still need further help please just ask and I will answer your questions. Please rate the answer. Thank You for using Fix Ya. Roger

Feb 15, 2011 | 2000 Buick Park Avenue

1 Answer

How do I replace tie rods on front passenger side


loosen lock nut. clamp vice grips on inner tie rod to hold it from turning. Then unscrew tie rod end, counterclockwise. count the number of turns so you can screw new one on in same place. get front end alignment.

may need to heat the tie rod end with a torch to break it free from the rust.

soak for a week with penetrating oil first.

Oct 15, 2010 | 1998 Ford Taurus

1 Answer

How difficult to replace inner tie rod end on 06 silverado 2wd?


Not that hard, just spray the tie rod sleeve with WD40 night before and let it soak in. Remove the collier pin and and nut and hammer the old inner tie rod end out of the Track rod with a 5 pound sledge hammer. Remove the inner tie rod end from the sleeve and don't forget to mark the distance so you can place the new tie rod end at the same length. Reinstall the inner tie rod end to the Track rod and tighten the nut and replace the collier pin with a new one. Grease the fitting and go for a test drive, if the truck does not wonder then your good to go with out a alignment. Good luck and hope this helps, Note, make sure you have to right inner tie rod ends. Each side has different thread rotations.

Jun 03, 2009 | 2006 Chevrolet Silverado 1500 2WD

1 Answer

Replace rack/pinion


The book calls for about 5 hours labor with a lift, air tools, and experience. It's a tough job. Here are a few tips, Take the lines loose from the rack; not the pump. With the tires off, Remove the nuts from the outer tie rods.Run the nuts back on the tie rods stud and hit the steering knuckle where the tie rod's stud goes through.This will free the stud. Remove the steering shaft from the rack.(take the bolt all the way out.Remove rack mounting bolts. Twist,pull ****,and fight the rack out the side of the car with the most room. The new rack will have inner tie rods already installed. Make sure the new rack is centered.(Turn left then right count the turns then center same # of turns from left to right). Count the threads or measure from the outer tie rod's jam nut to the last thread on the inner tie rod.(you can leave the jam nut in place and take the outer tie rod off and measure from the jam nut to the end of the rod.)Install the outer tie rods. Replace rack in car. hook up steering shaft.Bolt up rack. Hook up lines. Add fluid and work rack back and forth to bleed air. recheck fluid. Have it aligned. (or just take it to a shop.This job is going to be a nightmare!!!)

May 23, 2009 | 1999 Ford Taurus

1 Answer

1994 chevy cavalier,inner tie rod end.


Usually they can be replaced with a little effort. You would need to get under the car and pry the broken part off the control arm. The tierod end is threaded onto the shaft. There is a bolt which compresses the tierod end onto the tierod. Loosen the compression bolt and unthread the end from the shaft rod. Counting the number of turns to remove it will be the number of turns to replace it. Mount it and then get a front end alignment which is a good idea before something else breaks.

Apr 18, 2009 | 1994 Ford Escort

1 Answer

Inner tie rods


you can rent the tools for free when you buy the tie rods from autozone, o'reilly's etc. tool loosens tie rod.

Jun 05, 2008 | 1989 Ford Taurus

Not finding what you are looking for?
1999 Ford Taurus Logo

748 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...