Question about 1995 Toyota T100 Xtracab

Open Question

Cv joint how do you remove a cv joint on a toyota t100 4x4

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
chiquititas
  • 1010 Answers

SOURCE: removal of cv joint

Go to a mechanic, safe way...

Posted on Jun 22, 2008

Ad
  • 6982 Answers

SOURCE: 1998 grand cherakee driver side cv joint removal

You can find instructions for doing this in any half decent manual. One thing they usually don't tell you is when removing the large axle nut on the end, it helps to put a spare tire on with no center cap and with the vehicle on the ground, break that nut free before starting the job. without air tools, it's next to impossible to remove it when jacked up.

Posted on Mar 10, 2009

yotaguy
  • 232 Answers

SOURCE: replacing CV Joints

Yes you can remove the drive shaft by unbolting the bottom ball joint,then removing the nut that holds the shaft in the hub I would'nt recommend trying to replace just the CV joint as this can be a very complicated procedure involving specialized tools and more than just general mechanical skill,this isn't true of all,as some CV's come apart fairly easily.If the joint is bad you should probably just replace the axle.Remember to match mark any adjustable parts you may have to disassemble,and when you reassemble make sure to check the splines of the shaft and the drive hub,remove any foreign material and carefully file or sand any burs or scratches,any of these can cause the spline to bind on reassembly and possibly cause irreparable damage to one or both parts.Good luck hope this helps.

Posted on Apr 10, 2009

  • 10 Answers

SOURCE: cv joint replacement 1998 isuzu trooper 4x4

This is a simple job that is why it is not very detailed in your book. Nothing special. Do one side at a time so you have a reference to how to reassemble it. Remove your tire , brake calipers be sure not to stress the rubber brake lines or open the brake lines to air. Remove both upper and lower ball joints. When taking out the ball joints remove the cotter pin and bolt and beat the **** out of the joint for it to release. Then the C/V axles will come right out with a bit out encouragement. You will need a few tools wrenches pry bar hammer. I would buy a Chilton's or a Haynes repair manual for torque specs for reassembly. Good luck and take your time. And unless the axles are making noise you can just replace the rubber boots. Which is alot cheaper.

Posted on Jun 01, 2009

  • 173 Answers

SOURCE: cv joints

The process is a little involved. Try going to Autozone.com and see if they have a repair guide online to look at the process.

Hope this helps...

Mike

Posted on Nov 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace a cv joint


I can tell you how to replace the CV joint but it is by far better to just buy a re-manufactured axle. The price of the CV joint itself then the labor to remove the axle, change the joint and install it is a big pain. Changing just the CV joint is labor intensive and you could run in to problems. Don't risk it, but a rebuilt.

Mar 23, 2014 | 1994 Toyota Camry

1 Answer

Replace axle but not cv joints


"What we have here is a failure to communicate". The axle comes with CV joints on the end. You will be buying the rebuilt assembly. Both axle and CV joints will refer to the same part in a front wheel drive application.

Feb 19, 2014 | Toyota Sienna Cars & Trucks

1 Answer

Pulling a cv axle from a 97 toyota rav4


mark the relationship of the inner cv joint to the flange.place a large screw driver between wheel studs hold driveaxle and remove the inner cv joint to axleshaft flange nuts remove the freewheel hub remove the driveaxle snap ring and spacer pull the inner cv joint off the axleshaft flange studs lower the inner cv joint and pull the driveaxle assembly out of the steering knuckle.let me know if this helps.

Jan 24, 2012 | Toyota RAV4 Cars & Trucks

1 Answer

Dashboard warning light second on the dash board of a Toyota corolla E110 series we have replaced CV joints and i think there are slightly different in either the size or the sharp but the tooth are...


Hi P,
I think that the warning light that has come on is the ABS warning light. If you look at the CV joint which has been removed from your vehicle, you'll see a ring gear that looks like a cog on the widest part of the old CV joint. That cog ring should be carefully removed and then fitted to the new CV joint. That's the rotor which sends an electrical pulse to the ABS system. Without it the Abs system can't work.
Please rate this answer
Best regards Johngee10

Feb 10, 2011 | 2003 Toyota Corolla

1 Answer

Pass cv joint will not come out of carier, removed clip, what next ? 97 toyota avalon...


This is for the removal of the passenger side cv joint. If the Avalon carrier is like the Camry you will have to remove the snap ring and the set bolt. You have 2 choices to get the carrier bearing out,(1) remove bracket, and take it out with the cv joint as yiu noticed the bolts are in tight spot (2) You will need a torch with a rose bud tip and put a lot of heat (red hot)on the cast iron bracket and be in postion to hit the cv joint bearing (on the tire side of carrier) with a hammer and drive it out. This is the way I prefer but, take caution with flame. Do step 2 only if you are planning on replacing the cv joint anyway.

Jul 17, 2010 | 1997 Toyota Avalon

1 Answer

Cv axle replacement in a 1994 toyota celica gts


Jack up the car, remove the tire, you'll need to remove the axleshaft nut, disconnect the strut from the wheel hub. You can pull the wheel hub towards you. This should give you enough room to get the outer CV joint out of the hub, you may need to take off the brake caliper, and tie it back for more room. You'll need to use a pry bar to pop out the inner CV joint out of the transmission. Some stores rent a tool to use to remove the inner CV joint from the transmission.

Mar 16, 2010 | 1994 Toyota Celica

1 Answer

What's involved in changing a cv joint in a 2000 Rav 4? I have very good mechanical abilities & have changed cv joints before (about 10 years ago)


Easy enough job really, jack car up, put axel stand under. remove wheel - remove hub nut, remove pinch bolt - prise open the pinch bolt part (sorry cant rem name) pop out the hub from the lower arm. Remove CV join from drive shaft. Usually a tap will pop it out.. sometimes theres a circlip that need removing (models vary). Grease up new CV joint - put grease in new boot, pop boot over drive shaft. put cv join on (replace circlip if provided in kit). join cv to hub - attach CV boot fully. fasten hub nut, replace wheel.

done. might need tracking again or aligning once you do this.

Feb 14, 2010 | 2000 Toyota RAV4

1 Answer

Need to know how to remove cv joint for clutch replacement in 2004 toyota corolla s


Take out the drive-axle. Cut the old rubber-boot clamps off and discard them.
Remove the boot from the inner CV joint nnd slide the tripod from the joint housing.
Remove the snap-ring with a pair of snap-ring pliers.
Drive the tripod the tripod joint from the drive-axle with a brass punch and hammer; careful not to damage the bearing surfaces or splines on the shaft.


Oct 31, 2009 | 2004 Toyota Corolla

1 Answer

1992 Toyota Corolla CV Joint


You can pick up an entire re manufactured axle assembly at your local auto parts store. In order to replace the assembly you will need to disconnect the tie rod end and the ball joint. Remove the spindle nut. Push the axle stub out of the hub. Now with a suitable container under the axle to catch spilled fluid pry the axle from the transmission housing. Install is the reverse of removal. For more detailed instructions and diagrams go to www.autozone.com vehicle repair guides.

Oct 29, 2009 | 1992 Toyota Corolla

1 Answer

Can not remove CVjoint on the drivers side of my toyota camry


no just put a good sized flathead screwdriver in between the end of the cv joint and where it goes into the transmission and pop it out

Mar 22, 2009 | 1990 Toyota Camry

Not finding what you are looking for?
1995 Toyota T100 Xtracab Logo

Related Topics:

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...