Question about 2003 Dodge Stratus

1 Answer

2003 stratus cam sensor replaced still unresolved

2003 dodge stratus cam sensor code replaced both cam and crank sensor still have same code replaced ecm still same code bypased wires still same code. car starts and runs fine up to 2400 rpm

Posted by on

  • Keith Heavilin
    Keith Heavilin May 11, 2010

    Have you checked your PCM to make sure that it has not gone bad?  That's what it sounds like it could be.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 137 Answers

You bypassed the wires that connect to the sensors? that would have been my first guess the harness that plugs into the sensor. after that i would check the ground connection from the ecm. wouldn't hurt to check the battery posts too. if the battery posts are oxidized you can have all kinds of goofy electrical problems. hope that helps.

Posted on May 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you perform a relearn procedure on a camshaft position sensor for a 2003 Dodge Stratus


Chrysler P0340 Cam Sensor Replacement - YouTube

? 4:01
www.youtube.com/watch?v=Lf85sxxDwc0
Oct 14, 2008 - Uploaded by markjhicks Hello, I have a 2003 Dodge Stratus. I have no starting ... It throws the 0344 code even with a new cam position sensor. Symptoms are it coughs ...

Sep 12, 2015 | 2003 Dodge Stratus

1 Answer

03 stratus replaced broke timing belt,crank and cam sensor it cranks has fuel and spark but no start whats up?


If your sure the timing belt is correctly installed, then check compression. you very well may have bent some valves when the timing belt broke. low or no compression will be a sign that this is the case.

Jul 17, 2011 | 2003 Dodge Stratus

1 Answer

My 1999 2.4 dodge stratus wont run unless i unplug cam sensor its a new sensor and a new crank sensor


I'm having excatly same problem, found this sequence to ge the car running again..turn off ign, unplug cam position sensor, crank for 2 seconds, connect cam shaft sensor, crank again and it starts like that...

Apr 01, 2011 | 1999 Dodge Stratus

2 Answers

I have a 2003 Dodge Stratus 2.4L DOHC Engine. The


it went from a hard cam sensor failure to an intermittent theres no magnet just a raised portion on cam.i think you got a loose terminal in the connector or a wire shorting or partly open from the sensor to the pcm

Mar 25, 2010 | 2003 Dodge Stratus

1 Answer

98 dodge stratus,engine light came on and it died and won't start now.What could be wrong?


when you crank the engine over now, does it sound different than before? if yes, you probably have a broken timing belt. it is also common for the cam gear to slip out of position from the cam and cause an incorrect, but hard to diagnose, timing issue. other no start with check engine light on issues could be a faulty cam or crank sensor.

pull the codes from the vehicles computer. if there is a cam or crank sensor code, or if there is a code that says in some different wording "cam sensor signal does not match crank sensor singal", first check crankshaft to camshaft timing. if belt is ok and timing marks line up then i strongly suggest removing the bolt from the camshaft that holds the cam gear on. with the bolt and cam gear removed you should be able to tell if the cam gear has rotated on the camshaft. there should be a small pin sticking out of the camshaft. if it is broken off then you need to replace the camshaft. if the pin is still there and the timing is good then replace iether the cam or crank sensor depending on what code you have stored in the ecu memory. if the code is not for the cam/crank sensor then google search the code number e.g. "p0502" and your make and model.

Mar 23, 2010 | 1998 Dodge Stratus

1 Answer

2003 stratus both sensors replaced still unresolved


Have the exact problem. Replaced cam sensor and timing belt. Still happens intermittently. code is p0344.

May 30, 2009 | 2003 Dodge Stratus

1 Answer

My 2002 dodge stratus serges when i accerate. I


Sounds like a throttle position sensor, but the comp should be coding the error in any case. How did you know to replace the crank and cam sensor?

May 06, 2009 | 2002 Dodge Stratus

1 Answer

2001 dodge stratus wont start


SORRY TO SAY BUT WHEN ONE SENSOR GOES BAD 90% OF THE TIME BOTH GO BAD AT THE SAME TIME. YOU WILL ALSO HAVE TO REPLACE CRANK SENSOR .WITCH IS ABOUT 80 BUCKS AT THE LOCAL AUTO STORE SUCH AS ADVANCED AUTO OR AUTO ZONE . BOTH CAM SHAFT SENSOR AND THE CRANK SHAFT SENSOR. THIS SEEMS TO BE A PROBLEM WITH THE DODGE STRATUS. GOOD LUCK. KENNY

Mar 02, 2009 | 2001 Dodge Stratus

Not finding what you are looking for?
2003 Dodge Stratus Logo

Related Topics:

515 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...