Question about 2000 Chrysler Concorde

1 Answer

Cant remove oil pan

Is there any way to remove the oil pan on a 2001 2.7l concorde v6 without removing the stabilizing bar?

Posted by on

  • vrollins300 May 28, 2009

    Thanks for the help, ENSANE1970. That's sounds a lot better than taking the suspension apart.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 54 Answers

You should be able to remove it after you take off the engine mount bolts and then jack up the engine, at the bell housing. This should give you enough clearance to get it out.

Posted on May 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I get oil pan off on a 2000 Saturn LW300 V6 3.0L


The official shop manual reads :
Remove nose cone brackets bolts from oil pan.
Remove lower transmission flange to oil pan bolts.
Remove oil pan bolts.
Using designated pry points to break loose the seal. Bump the pan with a rubber mallet to loosen the pan from the engine block.
Remove oil pan.
By the illustrations, the only thing in the way is the oil pickup tube.... Good luck !
t

Nov 21, 2014 | Saturn Cars & Trucks

1 Answer

I dont have enough clearance to remove oil pan out of a 2003 concorde 3.5 v6 removed stabilizer bar & transaxle oil pan support plz give me a tip on this


Daniel ,truly god bless you ,that is one heck of a job , ok with that said ,I just read that chapter just now an the only thing is that I could find is that you have it on some kind of ramps holding it up in the air , if that's it you may have to jack the frame up letting the wheels hang down giving you more clearance ,you can also try undoing the motor mounts and tranny mount and jack up motor ,and yes there is little to grab to do this and trust me the book isn't much more help . I REALLY hope this gives you the help you wanted ,good luck .
Woody. P.S. get back to me if theres any thing elese I can do.

Aug 28, 2014 | 2003 Chrysler Concorde

1 Answer

Need to replace oil pan on a bmw 2004 330ci


Raise engine with special tool 00 0 200 approx. 5 mm.
- Remove suction filter housing. Remove engine splash guard.
- Drain engine oil. On vehicles with automatic transmission:
- Disconnect oil lines from automatic transmission and from oil pan.
- Release guide tube for dipstick.

Note: M52TU and M54 only.
- Detach return hose from cyclone oil separator on oil dipstick guide tube.
- Replace O-ring.
- Remove front end reinforcement.
- Detach steeling spindle from steering gear.
- Remove vane pump for power steering unit (lines remain connected).
- Disconnect plug connection to oil level sensor.
- Loosen top and unfasten bottom of left and right engine mounts.

E46 4WD only
- Remove left and right swivel bearings.
- Remove output shafts. Remove front propeller shaft.
- Remove front axle differential.
- Detach brackets for left and right control arms from engine carrier.
- Release retaining brackets for left and right stabilizer bars.
- Unfasten screw connection on front axle support and lower the front axle support.

Note: There is no need to detach the steering gear from the front axle support.

- Unfasten oil sump screws at transmission and engine ends.
- Lower and remove oil sump.
Sealing faces clean and free of seal debris.
Apply approx.3 mm wide, 2 mm high coat of Drei Bond 1209 sealing agent to the area around seams.

Installation:
  1. Replace gasket
  2. Install oil sump.
  3. Insert all oil sump screws.
  4. Insert screws in transmission end without preload at this stage.
  5. Tighten down screws in engine end.
  6. Tighten down screws in transmission end.

E60 Removing And Installing, Sealing Or Replacing Oil Sump (M54)

Necessary preliminary tasks. -
- Remove intake filter housing
- Remove guide tube for oil dipstick
- Lowering front axle support
- Drain off engine oil
- Disconnect plug connection to oil level sensor.

On vehicles with automatic transmission:
- Detach oil lines from automatic transmission and from oil pan.
- Unfasten oil pan screws at transmission and engine ends.
- Lower and remove oil pan.

Installation:
Sealing faces clean and free of seal debris.
Apply approx.3 mm wide, 2 mm high coat of Drei Bond 1209 sealing agen to the area around seams.

Installation:

  1. Replace seal.
  2. Install oil sump.
  3. Insert all screws on transmission end, without preload at this stage.
  1. Tighten down screws on engine end.
  2. Tighten screws on transmission end.

Or take it to a dealer....

Apr 19, 2011 | BMW 330 Cars & Trucks

1 Answer

Oil pan is not clearing the sway bar and frame. How do i get the pa m completely off the car?


Where the sway bar meets the cradle the are two bolt that hold a sway bar bushing down on both sides. The bolts have a 15mm head on them. Remove the two on the driver side only they are easiest ones to get to. Once you have them out you should be able to push the sway bar back far enough to get the pan to drop.

Nov 28, 2010 | 2004 Chrysler Concorde

1 Answer

Can i remove oil pan without removing engine 1984 s10 2wd 2.8 v6


Yes, you can remove the pan without removing the engine. You may have to remove anything preventing you from getting the pan out or you may have to disconnect the engine mounts and raise the engine enough to get the pan out.

Apr 18, 2010 | 1984 Chevrolet S-10

3 Answers

Replace swaybar 1999 silverado



Removal & Installation

  1. Raise and support the vehicle.
  2. Remove the tire and wheel.
  3. Remove the stabilizer shaft nut from the link bolt.
  4. Remove the stabilizer shaft link bolt.
  5. Remove the stabilizer shaft link insulators and spacers.
  6. Remove the oil pan skid plate, if equipped.
  7. Remove the stabilizer shaft insulator bracket bolts.
  8. Remove the stabilizer shaft bracket.
  9. Remove the stabilizer shaft.
  10. Remove the stabilizer shaft insulators.
  11. Inspect all of the parts for wear and damage.

To install:
  1. Install the insulators to the stabilizer shaft.
  2. Install the stabilizer shaft.
  3. Install the brackets over the insulators and the stabilizer shaft.
  4. Install insulator bracket bolts and tighten to 37 ft. lbs. (50 Nm).
  5. Install the stabilizer shaft link insulators and spacers.
  6. Apply Loctite® on the threads of the stabilizer link bolts then install the bolts.
  7. Install the stabilizer shaft nut to the link bolt and tighten to 89 inch lbs. (10 Nm), and continue to tighten the nut until 2-4 threads protrude above the nut.
  8. Install the oil pan skid plate, if equipped.
  9. Install the tire and wheel assembly.
  10. Remove the safety stands
  11. Lower the vehicle.

Mar 30, 2010 | 1999 Chevrolet Silverado 2500

1 Answer

I need to know how to replace the oil pan gasget of my 1999 concorde. 2.7


you will have to remove engine to replace pan gasket on this vehicle big job good luck

May 27, 2009 | 1999 Chrysler Concorde

1 Answer

I cracked my oil pan and i need to know if i need to take out my engin to change it i'm low on cash i need help


here's v6 3.8L

Section 03-01A: Engine, 3.8L 1996 Thunderbird, Cougar Workshop Manual
IN-VEHICLE SERVICE Oil Pan/Oil Pump Screen Cover and Tube Removal
  1. Disconnect battery ground cable (14301).
  1. Remove air cleaner outlet tube (9B659). Refer to Section 03-12 .
  1. Remove two bolts retaining radiator upper sight shield (8C291) and position radiator upper sight shield aside.
  1. Remove hood weather seal.
  1. Remove windshield wipers.
  1. Remove LH cowl vent screen and wiper module.
  1. Install Three Bar Engine Support D88L-6000-A or equivalent.
  1. Raise vehicle on a hoist. Refer to Section 00-02 .
  1. Remove front engine support insulator through-bolts.
  1. Partially lower vehicle.
  1. Raise engine and support with Three Bar Engine Support D88L-6000-A or equivalent.
  1. Raise vehicle.
  1. Remove starter motor (11002).
  1. Position drain pan.
  1. Drain engine oil.
  1. Remove oil bypass filter (6714).
  1. Remove starter motor wire, ground strap and automatic transmission oil cooler lines.
  1. Remove oil pan-to-bell housing bolts and bolts at crankshaft position sensor lower shield.
  1. Remove remaining oil pan retaining bolts.
  1. Remove steering shaft pinch bolt and separate steering shaft.
  1. Position transmission jack under front sub-frame (5C145).
  1. Remove six rearward bolts on front sub-frame. Loosen two forward front sub-frame bolts.
  1. Remove lower shock absorber-to-front suspension lower arm bolts and nuts (both sides).
  1. Lower front sub-frame.
  1. Remove oil pan (6675).
  1. Empty any residual oil from oil pan.
  1. Remove oil pump screen cover and tube retainer bolts and support bracket nut. Remove oil pump screen cover and tube (6622) and discard oil pump inlet tube gasket (6626).

Apr 14, 2009 | 1996 Ford Thunderbird LX

1 Answer

2001 Concorde 3.2 L Oil Pan Removal


if you have your old drain plug take it to a auto part store get a self tapping drain plug! save big$$$$$ I have installed piles of these they last for ever $5-$20- for one. cheers

Dec 24, 2008 | 2001 Chrysler Concorde

Not finding what you are looking for?
2000 Chrysler Concorde Logo

Related Topics:

196 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...