Question about 2008 Chevrolet Hhr

2 Answers

2008 HHr headlights aimed too high.

It is very obvious that our HHr's headlights are aimed too high.  Everyone hates our dims and the owls are not very happy with our brights.  I was totally amazed at the air cleaner assembly so; I thought I would seek out help on this procedure before I attempted to adjust the lights.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

You need a 6mm hex socket (Allen wrench) To adjust up and down.I can't find anything on horizontal yet. The adjustment is in a hole behind the bulb, under the hood.

Posted on Aug 02, 2012

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

There should be some screws at the back of the headlights where they go in u would have to adjust those

Posted on May 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Driver side low and high beam on but dim. Passenger side low beam normal but high beam on and dim


I would check for the groundwire continuity

Driver side - dim low beams and no hi beam - Subaru Outback ...

www.subaruoutback.org > ... > General > Electrical & Electronics
Oct 11, 2014 - Hi everyone, My drivers side headlights are dim on low, (car has separate bulbs ... When the headlight switch is turned ON, but for low beams, ...

Driver-side Low beam Not Working (electrical issue not bulb ...

www.hummer4x4offroad.com/.../showthread.php?...Driver-side-Low-be...

Mar 12, 2015 - 10 posts - ‎4 authors
The high beam continues to work on both sides...I pulled the Driverside headlamp fuse and then both left and right beams lit up but very dim.

High beams ok, but not low beam - one side only - TDIClub Forums

forums.tdiclub.com > ... > VW MKIV-A4 TDIs (VE and PD)
Jan 23, 2014 - My driver's side lights are working fine - high and low beams. ... But it definitely looks like the big lamp on the driver's side gets brighter when ..... Drivers side headlight is very dim on low beam and goes out when on high beam ...

Dim driver's side headlight (low & high beam) - GrandAmGT.com Forum

www.grandamgt.com > ... > Technical Q&A

Dec 11, 2002 - 6 posts - ‎4 authors

Jan 04, 2016 | Cars & Trucks

1 Answer

Ford escort no headlights on dim or high beam


check fuse for signal switch and all other related fuses. most likely if the switch is good. the bulbs are bad. lol

Jul 02, 2012 | Cars & Trucks

1 Answer

How do you access the headlights on a 2008 chevy hhr I need to change them.


Most Chevy headlights are held in place by three 10 mm bolts...as you remove all 3, you can lift the headlight assembly forward and expose the headlight bulbs...be sure to use bulb lubricant when installing the new bulbs, also wear gloves so you do not touch (harmful hand grease) the new bulb filaments...our normal hand grease can cause shorter bulb life. Hope this helps.

Apr 06, 2012 | 2007 Chevrolet HHR Panel LT New Cars

1 Answer

Can't find the adjustment screws for the headlights on a 2008 Tundra


Adjust the vertical headlight aim into the specified range by turning aiming screw A with a screwdriver.
  • Perform lo beam aim adjustment.
  • The headlight aim moves down when turning the aiming screw clockwise, and moves up when turning the aiming screw counterclockwise.
  • 5687808.jpg

Oct 16, 2010 | 2008 Toyota Tundra

2 Answers

2008 hhr ls can't get to drivers side headlight bulb to change Please help?


This video will show you how to replace the headlight and also the bulb in the headlight of your HHR">

May 20, 2010 | 2008 Chevrolet Hhr

1 Answer

Need to replace headlight bulb 2007 hhr


H13 HALOGEN HEADLIGHT BULB, SOLD INDIVIDUALLY -- Low 55/high 65-watt halogen bulb; 12.8 volts; P26.4t base; A high quality, direct fit OE replacement headlight bulb

3c8c3dc.jpg


How to Replace a Headlight Bulb
(DIY Complexity: Easy / Time: 0.9 hour)

Parts:
1. Headlight Bulb

Tools:
1. Screwdriver
2. 1/4 in. Drive Ratchet
3. Socket Set

Steps:
Step 1 Open the hood and locate the headlight assembly.
o Tip: Most headlight assemblies have a place in the rear to gain access to the headlight bulb.
o Tip: It is recommended that headlight bulbs are replaced in pairs.
o Tip: Always make sure the struts on the hood can fully support the weight of the hood so that it does not close on you while working. The use of a hood prop can securely hold it in place.
o Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.

Step 2 Gain access to headlight bulb.
o Tip: It is a good idea to check the high beam and low beam headlight bulbs at this time.

Step 3 Disconnect the wiring harness and replace the old headlight bulb with a new one.

Step 4 Turn on the headlights and check high and low beams to verify repairs.

Hope this help (remember rated this help). Good luck.

Mar 30, 2010 | 2008 Chevrolet Hhr

2 Answers

2008 Jeep Grand Cherokee has a headlight aiming problem - the low beams are aimed too high. I cannot find the vertical aiming adjustment screws to fix the problem. Can anyone tell me how to adjust the low...


Hi, i have no idea if this will help you or not, but, on the 1997 grand cherokee, if you look at the headlight itself, look to the outer edge, over the top ontop of the headlight there is a white allen key hole, not sure on the size, this, basically is the up and down adjuster for the headlight, sorry if it doesn't help but i've just had to adjust mine, and thats where it is, the one towards the radiator is the in and out, it pushes or pulls the headlight offcentre

Nov 26, 2009 | 2005 Jeep Grand Cherokee

1 Answer

Headlight pointing down, loose in housing


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Nov 19, 2009 | 2008 Dodge Charger

2 Answers

1998 Ford Mustang Headlight Adjustment


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Mar 16, 2009 | 1998 Ford Mustang

1 Answer

Honda CRV 2007 dim headlights


add some driving lights or re aim your high beams lower so you can use them all the time.

Jan 13, 2009 | 2007 Honda CR-V

Not finding what you are looking for?
Cars & Trucks Logo

1,177 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...