Question about 1989 Dodge D150

1 Answer

Can't get fire

I have a 89 dodge d150 and i have changed the pick up coil and still bot getting any fire,what else could i do?

Posted by on

  • mike loshbough
    mike loshbough May 11, 2010

    try your crank sensor on the back side off the motor



1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 161 Answers

You should have a crank sensor that goes into the top of the bell housing . it will either be on the pass side or drivers side I believe on your year it is on pass side. if you reach back behind the intake behind the pass side head you will feel the sensor. it is held in by 1 bolt and feel the wire harness to follow and unplug it. they go bad often. and on yours you might even be able to see it if you lean over the back of the motor from pass side. it is the only sensor that goes into the top of bell housing where trans and engine go together . sometimes you have to move a few things out of your way to get to it like oil press sensor ect. and have you checked the coil? the crank sensors are pretty cheap just make sure you give the part store exact year and engine.

Posted on May 27, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

89 DODGE D 150 318

could be your coil is bad when it heats up it shorts out.

Sep 12, 2012 | 1989 Dodge D150

1 Answer

I got a 89 dodge d 150 v6 no fire at the coil can run a hot wire to the coil and it runs what does this regulator look like and where is it located

Try this jumper the ballast resistor on the fire wall if you have one looks like a block of white ceramic wit two or four wires. Jump them across not up and down If you check voltage on the right side 12 volt left side lower to protect coil from 12 volts. If that doesn't work your shut down relay may be bad. If not getting voltage to resister could be the starter switch on top of steering column under dash. Key switch is not ignition switch. The key switch pulls a lever up on the ignition switch if switch is not set right it will not send power to the coil. I had two break before on me. The book says to follow the wire all the way back to the battery and look for breaks

Feb 11, 2011 | 1989 Dodge D150

1 Answer

What is the firing order on a 89 dodge v6 3.9 liter and where is number one on the roter

For the 1988 thru 1996 Dodge 3.9L (238 cubic inch) V6:

Firing Order:

1 - 6 - 5 - 4 - 3 - 2


...................[.] clip

Aug 12, 2010 | 1989 Dodge D150

1 Answer

Change from inline 6 to a 318. cant get any fire from coil to the distruber

you should try getting a new coil or see if there is power to the coil first

Apr 13, 2010 | 1984 Dodge D150

1 Answer

I have 1992 Dodge D150 with 318 magnum. It won't

is this vehicle fitted with a chipped key ?? iam thinking factory immobilisor here?? but not sure what year it was introduced in america

Nov 22, 2009 | 1993 Dodge D150

2 Answers

89 dodge d150 no fire

The pickup coil is magnetic so take a small screwdriver and place it on one of the points of the pole peice and see if it has a pull on it first. It may be that item that went bad from excessive heat. That takes away the magnetivity in the long run most of the time

May 24, 2009 | 1989 Dodge D150

1 Answer

86 dodge 250 v8-318 no fire at spark plug, will not start

did you change the main coil and coil wire?if so then check the ing resistor and then the computor box

Mar 20, 2009 | 1989 Dodge D150

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides