Question about 1999 Cadillac Seville
Driver window not working and door lock. the passenger door lock works for the whole car and every other window works. I have the manual but it dosent tell me where in the hell the circut breaker is or witch fuse to check. I looked under the hood in the fuse relay box but i have no clue please help. also the master control pannel not working for all other windown or locks and memory forthe driver seat not working
The same circuit breaker feeds the driver door as well as the passengers doors . The wires inside the rubber boot from the body to the door are probably broke ,power or ground wire .Or the door module is bad . Are your familiar with electronic control modules ? The door functions ,windows , lock's , memory etc... are controlled by DDM - driver door module .
Door Control System Operation
This vehicle has five modules capable of performing door system control functions. Vehicle door system components (windows, locks, mirrors, etc.) are controlled directly by these modules. There is a door module located inside of each vehicle door:
• Driver Door Module
• Passenger Door Module
• LH Rear Door Module (LRDM)
• RH Rear Door Module (RRDM)
• LH Front Power Window Switch
Simple Bus Interface (SBI)
Each Door Module communicates with the other Door Modules on the SBI. The driver door module is the only Door Module that is capable of communicating over the Class 2 Data Line as well as the SBI.
Driver Door Module
The driver door module directly controls the LH Front door lock actuator, power window motor and the outside rear view mirror. The driver door module sends and receives messages received from the LH Front Power Window Switch to the passenger door module, LRDM and RRDM modules over the Simple Bus Interface (SBI) line. Also, the driver door module sends and receives message from other vehicle system modules via the Class 2 Data Line.
Pulling the door panel off an checking B+ voltage and ground for the module would be good for you to do , since you probably don't have a $6,000 factory Tech 2 scan tool to see if the DDM is communicating .
The driver door module has two main power feeds (high and low current), and two main grounds. The low power feed (battery 1) is used to provide power for the driver door module's logic and internal driver operation. The high power feed (battery 2) is used to provide power for systems that draw higher amounts of current (motors, lights, etc.). Operating current at the driver door module's battery should not exceed 3.0 amperes at battery 1, and 7.5 amperes (for 2 seconds) at battery 2 while the driver door module is awake, and 2.5 milliamps when the driver door module is asleep. For most driver door module functions, the driver door module will operate properly with a system voltage of 9.0-16.0 volts. If system voltages exceed 16.0 volts the driver door module will provide protection by disabling certain functions that may damage due to higher than normal system voltages.
What kind of manual do you have ? The info above is from a factory repair manual .
The fuse's ,circuit breaker for the door module are located in the rear fuse box , not under hood . PWR WDO circuit breaker 30 amp. , DRVMDL fuse 10 amp. The rear fuse box is located under the back seat . Watch this video ,different type vehicle but probably the same problem .
Dodge Grand Caravan No Power Window No Power Locks CAN Trouble
Posted on Jul 23, 2017
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
you need to have a pulley puller to get the pulley off if you don't have one most auto zone part stores have a loan a tool program and they can help you with that on most powersteering pumps the high pressure line will be a fitting or bolt on and the return line is usually just a squeeze clamp hope this helps good luck
Posted on Jan 30, 2009
First thing you have to do is list all the codes, because some some might be stored for a long time. Pushing the OFF and WARM buttons together and holding will ghive you all the stored codes. Then press OFF and HI together to clear all codes. Hold and wait for bars or 0's. Now start your car and let it get up to proper operating temps. Take car for aride that aincludes all phases of driving including highway speeds. Observe SERVICE ENGINE LIGHT for coming on . Assuming it does , repeat steps previously provided, read codes stored and repair accordingly. If need be contact me with new codes and I will try to assist you.
Posted on Mar 16, 2009
you will need to remove the parking brake cable from the caliper then remove the lower slide pin bolt, flip the caliper up and pull out the old pads and install the new ones. You should get the rotors machined for the best braking performance or replace them.
Posted on May 02, 2009
bang on the door hard and put the window up.if there is a dead spot in the motor from lack of use,the motor will start.
Posted on Jul 17, 2009
Tips for a great answer:
Jan 25, 2016 | Cadillac Cars & Trucks
Jan 03, 2015 | 1998 Cadillac Seville
Apr 27, 2014 | 2005 Cadillac STS
Apr 14, 2013 | 1999 Cadillac Seville
Sep 03, 2012 | 1997 Cadillac Seville
Feb 06, 2011 | 2001 Cadillac Sts
Oct 29, 2010 | 1998 Cadillac Seville
Sep 06, 2017 | 1999 Jeep Grand Cherokee
Jun 03, 2009 | 1999 Cadillac Seville
173 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: