Question about 2004 Chrysler Sebring

1 Answer

How do you get to back spark plugs

How do you get the back spark plugs on a 2004 Sebring Convertible

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 323 Answers

You'll need to remove the intake plenum. From there you can access the plugs and wires.

Posted on May 26, 2009

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

c17hydro
  • 2984 Answers

SOURCE: Spark plug location on sebring convertible

Depending on the tightness of the socket fit and the engine, carefully pull the spark plug out of the bore


ac34e37.jpg
Hope this helps some...best that I can find!

Posted on Jun 30, 2009

  • 93 Answers

SOURCE: Is it difficult to change the spark plugs on a

Yes. Yopu must remove the plenum, which means a new gasket.

The plug wires go down into the valve covers. The circular gaskets there often leak, so I would replace the wires and gaskets around them at the same time because it is all exposed.

Posted on Feb 02, 2010

ZJLimited
  • 17970 Answers

SOURCE: 1999 Chrysler Sebring Convertible code P1495. I

Code 1495 = Leak Detection Pump Solenoid Circuit

Remove the connector from the solenoid (should be on the back wall, just to the drivers side of the air-hat). You will have the solenoid to check and the harness. What you want to measure is the voltage coming from the harness and the resistance of the solenoid.

Turn the key to the "ON" position but do not start the motor; the voltage at the connector should be at least 10V or more,.now, check the resistance of the solenoid (should be around 35 ohms).

Hope helps.

Posted on Jun 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How easy is installing a expandable freeze plug on a 2004 Chrysler Sebring 2.7 6 cylinder lxi convertible


depending which one is being replaced usually not bad. however some require a frost plug install tool that has a flex able head to get into tight spaces. it maybe best to have a shop replace it as it makes a mess.

Apr 19, 2015 | 2004 Chrysler Sebring Convertible

1 Answer

How do you access the rear strut assembly on a 2004 Sebring Convertible? The videos show a trunk access but its not there?Is it located behind the back seat?


its in the trunk area over the wheel. you have to remove the trunk liner panel and then you can access the strut mounting bolts

Feb 17, 2015 | 2004 Chrysler Sebring Convertible

1 Answer

How to replace the back up light on a 2004 Sebring


really. you have to pull the light cover off. if its on the trunk lid side, I am just guessing but you have to pull the interior panel to get to the light bulbs

Oct 20, 2014 | 2004 Chrysler Sebring

1 Answer

How to remove driver door panel on 2004 Sebring convertible to replace external door handle


Panels usually push on with plastic clips or screws,some screws are hidden behind push in plug covers.

Jul 20, 2014 | 2004 Chrysler Sebring Convertible

1 Answer

Where is the speed sensor located on a 2004 chrysler sebring convertible???


The speed sensors are on the side of the trans that faces the front of the car. They are about midline height, with one of them near the seam between the engine and the transmission, and the other near the very far end of the transmission, basically on either side of the vertical shift rod. They simply unscrew, after lifting tab and removing the electrical plug, and screw back in to about the torque of a spark plug. They look very similar to one another.

May 17, 2011 | 2004 Chrysler Sebring

1 Answer

Where are the spark plugs on 2008 sebring convertable 2.4L


PLUGS ARE UNDER PLASTIC COVER...IT DOESNT LOOK LIKE IT BUT THE COVER WILL POP RIGHT UP...NO BOLTS.

Feb 25, 2011 | 2008 Chrysler Sebring Convertible

1 Answer

1999 chrysler sebring convertible jxi code p1495 intermittant shut off while driving. Replaced fuel pump and filter, distributor, spark plugs and wire. Was advised by ZJLimited to remove connector from the...


replacing the fuel pump relay is one thing but what about the (ASD auto-shut down) relay

additionally...
  • what engine size?
  • what transmission?
  • any codes?
  • does the pump run KOEO?
  • Do you have spark?
  • What is the cranking speed?

you may find faster service by subscribing to a "live chat" since there are so many questions and variables in your concern

Jun 03, 2010 | 1999 Chrysler Sebring

1 Answer

Is it difficult to change the spark plugs on a 2004 Chrysler Sebring Convertible V6


Yes. Yopu must remove the plenum, which means a new gasket.

The plug wires go down into the valve covers. The circular gaskets there often leak, so I would replace the wires and gaskets around them at the same time because it is all exposed.

Dec 01, 2009 | 2004 Chrysler Sebring

2 Answers

My 2004 chrysler sebring electical is not working.


Check around the MAP sensor area for any connections that may have been disturbed while you were replacing the sensor. Most or all of those functions are controlled by the body control module. I would think that a fault like that would show on the scanner readouts.

Aug 23, 2009 | 2008 Chrysler Sebring Convertible

3 Answers

Spark plug location on sebring convertible


Depending on the tightness of the socket fit and the engine, carefully pull the spark plug out of the bore


ac34e37.jpg
Hope this helps some...best that I can find!

Jun 30, 2009 | 1998 Chrysler Sebring

Not finding what you are looking for?
2004 Chrysler Sebring Logo

Related Topics:

326 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...