Question about 1995 Jeep Wrangler

2 Answers

Wont go into gear at all when car is running

I have a 1997 jeep goes into gear when car is running but when car is started it wont go into any gears

Posted by on

  • Ray Keckeisen May 11, 2010

    is this a manual transmission,do you mean when the car is running it will not go into gears

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 710 Answers

CHECK THE SLAVE CYLINDER RESERVOIR ON THE DRIVERS' SIDE FIREWALL. IT MAY BE IN NEED OF SOME BRAKE FLUID. IT IS RESPONSIBLE FOR THE ENGAGEMENT OF THE CLUTCH. IF IT IS LOW, THEN YOU HAVE A LEAK SOMEWHERE. A THOROUGH CHECK OF THE HYDRAULIC CLUTCH SYSTEM WILL LOCATE THE SOURCE OF THE LEAK. HOPE THIS HELPS. PLEASE KEEP ME POSTED. THANKS FOR USING FIX-YA AND FOR AN HONEST RATING. GOOD LUCK

Posted on May 26, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

If you have a manual transmission and you mean the car will go into gear when the car is moving but not when engine running and standing still you probably have a bad clutch or bad clutch linkage.

Posted on May 26, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1997 grand jeep cherokee wont start all the way it starts to then you hear a high pitch whine


Sounds like a starter shaft, housing or spring. Possibly a flywheel, but probably not. You might need to either tighten some starter bolts or replace the starter. If the starter bolts are tight, you don't want to tighten them anymore. That will tell you if your starter is loose or just needs to be replaced.

Feb 17, 2017 | 1997 Jeep Grand Cherokee

2 Answers

Jeep wont go into gear after sitting over night. Rev it up and it goes into gear. What could be the problem


probably a problem torque converter clutch servo/solenoid
run the fault codes

Oct 02, 2015 | Jeep Cars & Trucks

1 Answer

Jeep runs but will not change gears


automatic? trans, mines a 6speed, and has a clutch.
my guess is yes,
my A/T will not change gears,
all gears slip? (slip , flare or?)
or wont move at all. the car?????
or is stuck in1st gear in drive.?
or wont move in reverse. why not tell full story on so complex a device. super complex it is.
wont up shift , wont down shift
skips gears.
??????????????????

check fuses first.
then scan the PCM, it will tell you errors, called DTCs
use a real scan tool that can scan 2010 Jeeps. (factory codes !!!)
not some autozoned junk.

id bet there is a code, for sure.
even a broken shifter switch, or?

Aug 17, 2014 | 2010 Jeep Wrangler Sahara

1 Answer

I have a rover 200 i seem to be having probelms getting it into gear,when engine is off its fine goes in gear no problems,so there for i put gear into first start car up then take off and drive and its...


it could be your slave sinder.if you have a hydrilick cluth. if you have a cable that run the clutch it could be dab. or it most likely you clutch is on its way out

Oct 19, 2009 | 1997 Jeep Wrangler

1 Answer

After being stored clutch willnot engage


do you mean wont disengage? does the pedal feel normal, or like its pushing nothing?cant put it in gear? or goes in gear but wont move?. if you put it in gear but car wont move, the clutch is toasted. if you can put it in gear with the engine off, but not when its running, check the clutch master fluid. if its low or out, then the slave or master is leaking and you will need to replace both. if the clutch arm IS working, and the pedal feels normal, sometimes you can put in gear, and start it with the clutch pedal depressed and drive it, and goose the gas to "break the disc loose"

Oct 14, 2009 | 1997 Suzuki Sidekick

1 Answer

Jeep 1997 Wrangler. Gear shifting very hard


synchronizers are going bad a used trans would be cheaper than a rebuild due to the labor involved

Aug 19, 2009 | 1997 Jeep Wrangler

2 Answers

Jeep 1997 Wrangler. 6 Cyl Manual Having real trouble getting into gear, especially from stop. Grinding noise when backing up. Easier on gears 3/4/5 once moving. Can it be something as simple as clutch...


easy #1 check is what gear is hard when running turn car off it goes in easy probably just a clutch adj. or problem. gone unfixed can destroy the trans synchronizers

Aug 19, 2009 | 1997 Jeep Wrangler

2 Answers

95 Jeep wrangler wont go in gear


if this is something that started suddenly, it could be a leak in your master cylinder or slave cylinder, or your fluid could be low, or there could be air in the lines. Make sure it's full of fluid, and get back to me.

Jun 15, 2009 | 1995 Jeep Wrangler

Not finding what you are looking for?
1995 Jeep Wrangler Logo

448 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...