Question about 2000 Dodge Neon

1 Answer

Iam replacing the motor mount

The car only goes 25mph

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Dodge Master
  • 3,433 Answers

And?

Posted on May 26, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1989 Acura Legend LS, automatic. Car is at 4000 rpms before it goes to the next gear, at 25MPH. Is that normal.


could be normal shift timing set by the shifting solenoid's value related to the diagnostic board on the car i noticed some cars will hit that mark before shifting

Feb 27, 2017 | Acura Cars & Trucks

1 Answer

I rebuilt the TBI, Changed every sensor in the truck and replaced the heads. I still cannot pass the CA smog test


Check everything that is connected to a vacuum line, check the CAT and the injectors and last run a compression test.

Mar 13, 2014 | 1988 Chevrolet K2500

1 Answer

The support (dogbone) on the motor mount is cracked


This usually happens when the motor mount near the firewall goes bad, this will allow the motor to move more causing the dog bone to crack, both of these mounts should be replaced.

Oct 05, 2011 | 1993 Toyota Camry V6

2 Answers

98 buick park ave. shakes n shifts hard and noises, is this a transmission sensor?


sounds like a trans mount when they go bad it causes all kinds of shakes , have someone put in gear ,open hood,, watch motor. tell them to hold brake and give it a little gas .Don;t stand in front of car .....see if motor raises up if so replace all mounts motor included. this is a common fix on theses cars.

Mar 18, 2011 | 1998 Buick Park Avenue

1 Answer

Engine and speedometer surge when car is going about 20-25mph


GM had gauge cluster problems from 2000-2005. Bad stepper motors. On those units you have to replace the cluster or rebuild it with new stepper motors. Dealership fixed mine for $150.00

Oct 28, 2010 | 2004 Chevrolet TrailBlazer

1 Answer

Do i have to disconnect motor mount to replace my drive belt


Depends on the motor. If there is a mount on the passanger side that the belt goes around then yes. Don't fret though, easy to get around. Use a jack and a piece of wood on the oil pan to support the motor so you can remove the motor mount to remove the belt. Again, this is on SOME gm motors not all. On the others the mount isn't in the way at all.

Jan 24, 2010 | 1995 Pontiac Bonneville

1 Answer

Vibration through the car Transmission-motor Linkage?


Check to make sure both headlights are tight,,,when it rattles at idle go feel the headlight and hold it and see if the noise and vibration goes away,sometimes the headlight has too much clearance and causes a massive vibration,,if thats not it try...loosening all the motor mounts and rock the car back and forth and them retighten them,it reseetles the mounts and sometimes fixes the issue,,also check the lower engine and trans mounts for wear.

Oct 30, 2009 | Saturn SW2 Cars & Trucks

1 Answer

Motor mounts -frame mounts


Sure ,just save the mount from the chevy v-8 and they will bolt intp the frame!

Jun 24, 2009 | 1991 Chevrolet C1500

1 Answer

Replacing accessories belt 1997 bonneville (vin k)


on the 3.8 you have to take bolts out of motor mount and lift motor ...belt goes mount

Dec 10, 2008 | 1997 Pontiac Bonneville

Not finding what you are looking for?
2000 Dodge Neon Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...