Question about Honda Civic Coupe

1 Answer

Radiator problems Rad cap is broken on inside and overflow cap is missing. When i topped up coolant levels and let idle for 10min inside temp. gauge didnt come off of cold and the fan on the rad did not kick in.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Honda Master
  • 1,348 Answers

The radiator fan switch which drives the fan relay,needs to have hot coolant to operate properly,the temperature sending unit the same situation.you either have a thermostat that is stuck open,or alot of air circulating in the system.pressurize the system to 15 psi and see if it drops,if it does...you have a leak in it.my suggestion would be to fix the radiator properly.overheating that engine is going to result in needing a head gasket which is expensive.find a good used radiator.

Posted on May 26, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2002 Ford Explorer Sport no heat but the fan works,what could the problem be?


Could be that the thermostat has packed up...

Check all your coolant levels are correct and then take her for a good run out....keep your eyes on the temperature gauge,,if your temp gauge hardly moves then your thermostat is at fault....replace it.

If temp gauge works fine, you may be airlocked in your heater matrix... Try setting heater to full heat with fan on full power,, whilst car is ticking over, remove radiator / expansion bottle cap carefully and start squeezing your coolant pipes. This should force any air out through your rad/bottle top..

Please be aware that as your temperature rises in the engine. Your coolant will expand and start to flow out of the rad/expansion bottle..at this stage quickly replace the cap....check your heater...leave engine to cool....unscrew rad/bottle cap, check coolant levels, top up if necessary and squeeze pipes again..start car with heater/fan on full and repeat above.....

Hope this helps..

Nov 29, 2016 | 2002 Ford Explorer

1 Answer

How do i put water in my radiator?


you need to replace thermostat and radiator cap.look under hood around engine compartment.look for a radiator cap near radiator,add 50/50 antifreeze and water to coolant system to bring up boiling point.pure water will cause engine run hotter because water evaporate away,remove radiator pour coolant in the radiator until coolant stop dropping in the radiator now some vechicle pour coolant in the coolant overflow jug,pour coolant until coolant level stop dropping and the coolant level stay at cold full mark.start engie let idle few minutes, watch coolant level in radiator if coolant start dropping add more coolant, when coolant level stop dropping put radiator cap back on let engine idle until both top radaitor hose and bottom coolant hose get warm turn off engine wait until it get cool then take a large rag slightly open radiator just a litle at a time to keep from getting scaled.once radiator remove add more coolant if low,put radiator cap back on start the engine let it idle watch the temp gauge if temperature gauge going hot zone stop engine wait until cool then add more coolant,keep doing this until engine stop overheating going into hot zone and coolant level stop dropping,make the coolant overflow jug coolant level stay at full cold mark, dont let jug run empty if so air will get in the coolant system causing engine to overheat.

Jul 22, 2012 | 2000 Plymouth Breeze

1 Answer

No my alero is overheating. I have replaced the thermostat and waterpump and put a new cap on reservior and im losing coolant out the overflow


YOU NEED BLEED AIR OUT THE COOLING SYSTEM.WAIT TO ENGINE COOL DOWN.YOUR VECHICLE YOU HAVE TO POUR COOLANT IN THE COOLANT OVERFLOW JUG UNTIL COOLANT LEVEL STAY AT THE FULL COLD MARK.THEN START ENGINE LET IT IDLE A FEW MINUTES WATCH COOLANT IN THE OVERFLOW JUG WHEN IT DROPS ADD MORE COOLANT UNTIL COOLANT LEVEL STAY AT FULL COLD MARK.WHEN COOLANT LEVEL STOP DROPPING IN OVERFLOW JUG.SCREW RADIATOR CAP BACK ON OVERFLOW JUG WATCH ENGINE COOLANT TEMPERATURE GAUGE AS COOLANT TEMPERATURE START CLIMBING TURN OFF ENGINE LET IT SET A WHILE KEEP FROM GETTING SCALDED.TAKE LARGE RAG PLACE OVER COOLANT OVERFLOW JUG CAP SLOWLY OPEN RADIATOR CAP A LITTLE AT A TIME UNTIL PRESSURE RELEASE.REMOVE OVER FLOW JUG CAP.ADD MORE COOLANT UNTIL COOLANT LEVEL AT THE FUL COLD MARK ON THE OVERFLOW JUG.THEN SCREW CAP BACK ON THE OVERFLOW JUG.START ENGINE LET IT IDLE AGAIN WATCH ENGINE COOLANT TEMPERATURE GAUGE WHEN TEMPERATURE GAUGE START CLIMBING.TURN OFF ENGINE WAIT A WHILE.CHECK COOLANT LEVEL IN THE OVER FLOW JUG.DO THIS PROCEDURE UNTIL THE COOLANT LEVEL IN THE COOLANT OVERFLOW JUG STOP DROPPING AND STAY AT FULL COLD MARK,WHEN THE TOP RADIATOR HOSE GET HOT THERMOSTAT OPENING AIR IS OUT THE COOLANT SYSTEM. WHEN ENGINE COOLS DOWN.CHECK COOLANT OVERFLOW JUG COOLANT MUST BE IN THE COOLANT OVER FLOW JUG AT THE FULL COLD MARK WHEN ENGINE COLD. DONT .DONT OVERFILL COOLANT OVERFLOW JUG.KEEP COOLANT IN THE OVERFLOW JUG IF YOU LET COOLANT OVERFLOW JUG RUN DRY AIR WILL BE DRAW IN COOLANT SYSTEM CAUSE ENGINE TO OVERHEAT.

Aug 12, 2011 | 1999 Oldsmobile Alero

3 Answers

I replaced my radiator on my 2004 with a 2.2 and it seems like the thermostat is not opening. It can not get the air out. It seem to just to over heat and push the coolant out. Randy


REPLACE THERMOSTAT IF TOP COOLANT COOLANT HOSE GOING TO RADIATOR IS HOT TO TOUCH THERMOSTAT OPEN. TO BLEED COOLANT SYSTEM FIRST YOU NEED TO ADD COOLANT TO THE COOLANT OVER FLOW JUG UNTIL COOLANT LEVEL STOP DROPPING AND STAY AT FULL COLD MARK.WAIT 3 MINUTES IF COOLANT DROPS ADD MORE COOLANT UNTIL COOLANT STAY AT FULL COLD MARK.WITH RADIATOR OVER CAP OFF CRANK ENGINE FOR MINUTE WATCH COOLANT LEVEL AT OVERFLOW JUG.IF COOLANT DROPS ADD MORE COOLANT IN THE OVERFLOW JUG.WHEN COOLANT LEVEL STOP DROPPING IN OVERFLOW JUG.SCREW BACK ON THE RADIATOR CAP TO OVERFLOW JUG.WHILE ENGINE IDLING WATCH TEMPERATURE GAUGE WHEN TEMPERATURE START CLIMBING TURN OFF ENGINE WAIT A WHILE KEEP FROM GETTING SCALDED.WHEN COOLANT COOL DOWN SOME. PLACE A LARGE RAG OVER THE COOLANT OVERFLOW JUG OPEN CAP LITTLE AT A TIME UNTIL PRESSURE RELEASED, THEN REMOVE CAP ADD MORE COOLANT IN THE OVERFLOW JUG TO THE FULL COLD MARK.THEN REPEAT THE PROCESS SCREW BACK ON THE COOLANT OVERFLOW RADIATOR PRESSURE CAP.THEN START ENGINE WATCH TEMPERATURE GAUGE WATCH COOLANT TEMPERATURE GAUGE WHEN COOLANT TEMPERATURE START RISING TURN OFF ENGINE AGAIN WAIT UNTIL ENGINE COOL DOWN ENOUGH TO KEEP FROM GETTING SCALDED TAKE PLACE LARGE RAG OVER RADIATOR CAP WHICH IS THE COOLANT OVERFLOW JUG CAP OPEN CAP LITTLE AT A TIME UNTIL PRESSURE RELEASED ADD COOLANT UNTIL AT FULL COLD MARK. WHEN YOUR COOLANT LEVEL STOP DROPPING.AND TOP RADIATOR HOSE VERY HOT THERMOSTAT OPEN AND AIR IS OUT THE COOLANT SYSTEM. MAKE SURE YOUR COOLANT OVERFLOW JUG HAS COOLANT IN IT,WHEN ENGINE COOL DOWN CHECK COOLANT OVERFLOW JUG KEEP COOLANT LEVEL AT FULL COLD MARK.BECAUSE IF OVERFLOW JUG IS EMPTY THATS A SIGN RADIATOR COOLANT LEVEL LOW.WHEN OVERFLOW JUG EMPTY IT WILL ALLOW AIR GET IN THE COOLANT SYSTEM AND CAUSE CAR TO OVERHEAT.WHEN REPLACING THERMOSTAT ALSO REPLACE THE RADIATOR CAP ON THE COOLANT OVERFLOW JUG.

Aug 09, 2011 | 2004 Oldsmobile Alero

1 Answer

Need to know if i need to bleed the cooling system, after installing the radiator?


ADD COOLANT IN THE COOLANT OVERFLOW JUG UNTIL COOLANT LEVEL STOP DROPPING AND COOLANT LEVEL STAY AT THE FULL COLD MARK.PLACE COOLANT OVERFLOW JUG CAP BACK ON JUG.CRANK VECHICLE UNTIL ENGINE START WARMING UP. STOP ENGINE WAIT FOR A WHILE UNTIL COOLANT COOL DOWN TO KEEP FROM GETTING SCALDED. USE A LARGE RAG OVER THE OVERFLOW JUG CAP OPEN OVERFLOW JUG CAP A LITTLE AT A TIME REMOVE OVERJUG CAP CHECK COOLANT LEVEL ADD MORE. COOLANT IN THE OVERFLOW JUG.THEN START VECHICLE AGAIN.LET ENGINE IDLE UNTIL TOP RADIATOR GET HOT.THEN THERMOSTAT WILL BE OPEN.WHILE ENGINE IDLING WATCH THE TEMPERATURE GAUGE IN VECHICLE IF TEMPERATURE GAUGE START CLIMBING IN THE HOT ZONE.TURN OFF VECHICLE LET IT SET A WHILE THEN USE LARGE RAG REMOVE OVERFLOW JUG CAP.ADD MORE COOLANT, PLACE CAP BACK ON START VECHICLE AGAIN KEEP DOING THIS PROCEDURE UNTIL TEMPERATURE STOP CLIMBING HOT ZONE.AND WHEN COOLANT LEVEL STOP DROPPING IN THE COOLANT OVERFLOW JUG.AIR IS OUT THE SYSTEM, BUT KEEP COOLANT LEVEL IN THE COOLANT OVERFLOW JUG AT THE FULL COLD MARK.DONT OVERFILL.DONT LET COOLANT OVERFLOW JUG RUN DRY IF SO AIR WILL ENTER COOLANT SYSTEM BECAUSE COOLANT LEVEL WILL BE LOW ENGINE WILL START OVERHEATING.

Jul 24, 2011 | 2006 Dodge Grand Caravan

2 Answers

Changed thermostat. temp guage rising to "H" after about a week. little steam coming from radiator cap. reserve FULL and not going down. added coolant/water to radiator. temp gauge OK. could...


Hi,
If you are not seeing any leaks, most likely air in the coolant system, improper/weak coolant mixture, bad radiator cap, bad thermostat. Sounds more like the air and/or weak coolant to me.
Mike

Jun 20, 2011 | 1999 Chrysler Sebring

2 Answers

Having issues with a 2000 chevy impala overheating have changed the radiator and the thermostat fans seem to be working ok but overheats at idle in stop and go traffic, after a certain amount of time it...


YOU NEED BLEED COOLANT SYSTEM.CHECK COOLANT LEVEL IN RADIATOR.ADD MORE DEXCOOL UNTIL COOLANT LEVEL IS CLOSE TO RADIATOR SPOUT.CRANK ENGINE LET IDLE UNTIL TOP RADIATOR HOSE GET HOT.WATCH TEMPERATURE GAUGE.IF TEMPERATURE GAUGE START RISING TO HOT ZONE.TURN OFF ENGINE.LET COOL DOWN.USE LARGE RAG SLOWLY OPEN RADIATOR CAP A LITTLE AT A TIME UNTIL ALL PRESSURE RELIEVED.REMOVE RADIATOR CAP.ADD MORE COOLANT.CRANK CAR AGAIN LET IDLE UNTIL TOP RADIATOR GET HOT.KEEP EYE ON TEMP.GAUGE ALSO.WHEN TEMP.GAUGE STOP CLIMBING.YOUR COOLANT SYSTEM BLED.WHEN DONE LET CAR SET A WHILE CHECK COOLANT LEVEL.ALSO FIRST THING IN THE MORNING CHECK COOLANT LEVEL AGAIN.AND BESURE ADD COOLANT IN THE OVERFLOW JUG TO THE COLD MARK.DONT OVER FILL THE COOLANT RESERVOIR JUG.WORK SAFELY DONT GET SCALDED.

Feb 15, 2011 | 2000 Chevrolet Impala

1 Answer

How do i replace the water thmostat 99 6 cylider


WELL YOU NEED TO DRAIN COOLANT LEVEL BELOW THERMOSTAT LEVEL.YOU HAVE TO DISCONNECT MAF SENSOR LOOSEN AIRDUCT 2 LARGE CLAMPS LOOSEN REMOVE 4 SCREWS TO AIR FILTER COVER LIFT UP REMOVE COVER. THEN REMOVE AIR FILTER AND HOUSING, FIRST DISCONNECT MAF SENSOR.YOU HAVE TO DISCONNECT THROTTLE CABLE AND SHIFT CABLE.YOU HAVE TO DISCONNECT REMOVE THROTTLE BODY COOLANT HOSES DISCONNECT IDLE SPEED CONTROL VALVE CONNECTOR AND DISCONNECT TPS SENSOR CONNECTOR. THEN REMOVE THROTTLE BODY ASSEMBLY. YOU NEED TO BUY NEW THROTTLE BODY COOLANT HOSES AND NEW THROTTLE BODY GASKET FOLLOW TOP COOLANT HOSE TO ENGINE BLOCK.NOW YOU SEE CAN AND REMOVE THE THERMOSTAT HOUSING REPLACE THE THERMOSTAT.BESURE TO HAVE EXTRA COOLANT ON HAND.BLEED COOLANT SYSTEM WHEN DONE.TO BLEED COOLANT SYSTEM REMOVE RADIATOR CAP ON OVERFLOW JUG.THEN OPEN BLEED SCREW ON THE WATER PUMP BYPASS HOSE PIPE JUST A LITTLE.POUR COOLANT IN THE OVERFLOW JUG UNTIL LEVEL STOP DROPPING.STOP AT COLD MARK ON JUG.CLOSE BLEEDER SCREW ON WATER PUMP BYPASS HOSE PIPE.CRANK VECHICLE CHECK FOR LEAKS. START UP ENGINE LET IDLE FEW MINUTES THEN CHECK COOLANT LEVEL ADD MORE UNTIL UNTIL LEVEL STOP DROPPING.PUT RADIATOR CAP BACK ON OVERFLOW RESERVOIR. LET ENGINE IDLE WATCH COOLANT TEMPERATURE GAUGE.WHEN GAUGE START CLIMBING. TURN OFF ENGINE WAIT FEW MINUTES TAKE A LARGE RAG OPEN RADIATOR JUST A LITTLE YOU HEAR HISS NOISE.WHEN PRESSURE STABILIZE DONT GET SCALDED BECAREFUL.OPEN CAP LITTLE MORE.IF COOLANT PRESSURE STILL BOILS OUT WAIT 20 MINUTES ADD MORE COOLANT TO RADIATOR OVER FLOW WHEN COOLANT LEVEL STOP DROPPING.PUT RADIATOR CAP BACK ON START VECHICLE UP LET IDLE UNTIL THERMOSTAT OPEN. THEN FEEL TOP RADIATOR HOSE FEELS HOT THERMOSTAT OPEN WATCH TEMPERATURE GAUGE.IF GAUGE TEMP START CLIMBING TURN OFF ENGINE WAIT A WHILE.CHECK AND ADD MORE COOLANT.WHEN THE ENGINE CAN IDLE TEMP GAUGE STOP CLIMBING YOU HAVE BLEED COOLANT SYSTEM.KEEP CHECK ON COOLANT LEVEL.

Dec 29, 2010 | 1999 Oldsmobile Alero

4 Answers

I am putting in a new radiator on my 99 hyundai sonata 2.5 l how much radiator fluid do it hold


i do not know exactly but that size vehicle usually holds almost two gallons, fill it up, put the cap on the radiator, run the vehicle until the temp guage is at normal operating temp, then turn the vehicle off. after about a 15 min wait, use a rag and take the radiator cap off slowly and make sure there isn't any pressure behind it. after removing, top off the radiator again and fill the overflow tank to the max level. this should get all the air out and get you on the road again. check again everytime you get gas for a couple times making sure that the level is good.

Oct 16, 2009 | 1999 Hyundai Sonata

2 Answers

2004 impala coolant level


The coolant container (called the overflow reservoir) will be marked as to what constitutes MIN and MAX levels that should be in it. If it's low, add coolant.

As for what temperature it should run at, the gauge on the dash is just a general indication, but usually it runs close to the middle of the gauge's range.

Aug 08, 2008 | 2004 Chevrolet Impala

Not finding what you are looking for?
Honda Civic Coupe Logo

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...